Hydrothermal Reactions between Calcium Hydroxide and Amorphous Silica: the Reactions between 180 and 220°

1957 ◽  
Vol 61 (4) ◽  
pp. 473-479 ◽  
Author(s):  
Gunnar O. Assarsson
Keyword(s):  
Calcium Hydroxide ◽  
Amorphous Silica ◽  
Hydrothermal Reactions

Study of the Interaction between Calcium Hydroxide and Amorphous Silica Obtained from Serpentinites

2019 ◽  
Vol 93 (5) ◽  
pp. 924-931
Author(s):  
H. A. Beglaryan ◽  
N. H. Zulumyan ◽  
A. R. Isahakyan ◽  
S. A. Melikyan ◽  
A. M. Terzyan
Keyword(s):  
Calcium Hydroxide ◽  
Amorphous Silica

THE HYDRATION OF THE ALUMINATES OF CALCIUM: IV. HYDROTHERMAL REACTIONS OF TRICALCIUM ALUMINATE AND ITS HYDRATES

1943 ◽  
Vol 21b (4) ◽  
pp. 65-72 ◽  
Author(s):  
G. M. Harris ◽  
W. G. Schneider ◽  
T. Thorvaldson
Keyword(s):  
Calcium Hydroxide ◽  
Rectangular Plate ◽  
Hydrothermal Treatment ◽  
Saturated Steam ◽  
Partial Hydrolysis ◽  
Portland Cement Concrete ◽  
Steam Curing ◽  
Hydrated Alumina ◽  
Hydrothermal Reactions ◽  
Tricalcium Aluminate

A study was made of the hydrothermal reactions of tricalcium aluminate and its hydrates between 120° and 350 °C. Homogeneous samples of the hexahydrate of tricalcium aluminate may be prepared by treatment of the aluminate or its hexagonal hydrate in saturated steam at temperatures up to 150 °C. At temperatures of 250 °C. and above, under conditions favouring rapid hydrolysis, such as the addition of water to the anhydrous aluminate or hydroaluminate before autoclaving and rapid elevation of the temperature of the autoclave, crystals of calcium hvdroxide and of a hydroaluminate of lower lime–alumina ratio appear, usually mixed with the isometric hexahydrate. The new hydroaluminate occurs as rectangular, elongated, prismatic plates of low birefringence, refractive index 1.627, and has a lime–alumina ratio probably lower than 1.5. The hexagonal hydrate of tricalcium aluminate gives on hydrothermal treatment a better yield of the low-limed hydroaluminate than does the anhydrous aluminate. Only partial hydrolysis of the hexahydrate was obtained under any of the conditions used, but the hexagonal hydrate, autoclaved for 12 hr. at 350 °C., gave products composed almost entirely of the rectangular plate hydroaluminate and calcium hydroxide. No free hydrated alumina was found in the hydrothermal products.The rectangular plate hydroaluminate of calcium may also be prepared by the action of calcium hydroxide on hydrated alumina in saturated steam at 350 °C. It is therefore a stable product under those conditions.At temperatures below 250 °C. birefringent crystalline material is also formed on autoclaving tricalcium aluminate or its hydrates under conditions favouring hydrolysis. The experimental evidence indicates that one of the products is the birefringent calcium hydroaluminate formed on autoclaving the lower calcium aluminates at temperatures of 105 to 150 °C. (5).Precast Portland cement concrete products, when subjected to steam-curing, normally contain an excess of water, and the conditions for the formation of these birefringent hydroaluminates of calcium are therefore present. The same applies to the commercial steam-curing of other materials containing free lime and hydrated alumina. The formation of these hydroaluminates may explain the peculiar effect on the tensile and compressive strength of mortar and concrete test pieces produced by hydrothermal treatment at temperatures above 150 °C. (9).

Amorphous silica coating on α-alumina particles

1995 ◽  
Vol 53 ◽  
pp. 210-211
Author(s):  
J. W. Mellowes ◽  
C. M. Chun ◽  
I. A. Aksay
Keyword(s):  
Amorphous Silica ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Silica Coating ◽  
Full Density ◽  
Optimal Conditions ◽  
Fine Grained ◽  
Alumina Particles ◽  
Complete Mullitization ◽  
Powder Compacts

Mullite (3Al2O32SiO2) can be fabricated by transient viscous sintering using composite particles which consist of inner cores of a-alumina and outer coatings of amorphous silica. Powder compacts prepared with these particles are sintered to almost full density at relatively low temperatures (~1300°C) and converted to dense, fine-grained mullite at higher temperatures (>1500°C) by reaction between the alumina core and the silica coating. In order to achieve complete mullitization, optimal conditions for coating alumina particles with amorphous silica must be achieved. Formation of amorphous silica can occur in solution (homogeneous nucleation) or on the surface of alumina (heterogeneous nucleation) depending on the degree of supersaturation of the solvent in which the particles are immersed. Successful coating of silica on alumina occurs when heterogeneous nucleation is promoted and homogeneous nucleation is suppressed. Therefore, one key to successful coating is an understanding of the factors such as pH and concentration that control silica nucleation in aqueous solutions. In the current work, we use TEM to determine the optimal conditions of this processing.

Sign in / Sign up

Export Citation Format

Share Document