The Effect of Surface Roughness on Apparent Contact Angles and on Contact Angle Hysteresis. I. The system Paraffin–Water–Air

1953 ◽  
Vol 57 (2) ◽  
pp. 211-215 ◽  
Author(s):  
F. E. Bartell ◽  
J. W. Shepard
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Effect Of Surface

scholarly journals Effect of Surface Roughness on Contact Angle Hysteresis.

1991 ◽  
Vol 57 (544) ◽  
pp. 4124-4129 ◽  
Author(s):  
Kenji KATOH ◽  
Hideomi FUJITA ◽  
Masayoshi YAMAMOTO
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Effect Of Surface

WETTING OF ROUGH SURFACES

2004 ◽  
Vol 11 (01) ◽  
pp. 7-13 ◽  
Author(s):  
XINPING ZHANG ◽  
SIRONG YU ◽  
ZHENMING HE ◽  
YAOXIN MIAO
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Sessile Drop ◽  
Test Sample ◽  
Contact Angles ◽  
Sessile Drop Method ◽  
Equilibrium Contact Angle ◽  
Roughness Surface ◽  
Solid Substrates ◽  
Effect Of Surface

This paper focuses on effects of roughness on wettability. According to Wenzel's equation, the transition of theoretical wetting contact angles is 90°, whereas many experimental results have indicated that such a transition takes place at contact angles smaller than 90°. A new model of wetting on roughness surface is established in this paper. The model indicates that the influencing factors of wetting on roughness surface include not only equilibrium contact angle θ0 and surface roughness, but also the system of liquids and solid substrates. There is a corresponding transition angle for every surface roughness, and the transition angle is lower than 90°. Surface roughness is propitious to improve the contact angle only when θ0 is lower than the transition angle. The effect of surface roughness on the contact angle increases with the increase of rE. To engineer the surface with different roughnesses, a Ti test sample is polished with sandpaper with abrasive number 350, 500, 1000 and 2000; the contact angles of water on Ti are measured by the sessile drop method. The results of the theoretical analysis agree with experimental ones.

Roughness Effects on Continuous and Discrete Flows in Superhydrophobic Microchannels

2011 ◽  
Vol 9 (5) ◽  
pp. 1094-1105 ◽  
Author(s):  
Junfeng Zhang ◽  
Daniel Y. Kwok
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Slip Length ◽  
Contact Angle Hysteresis ◽  
Hydrophobic Surface ◽  
Contact Angles ◽  
Lattice Boltzmann Model ◽  
Roughness Effects ◽  
Apparent Slip ◽  
Velocity Changes

AbstractThe dynamic behaviors of continuous and discrete flows in superhydrophobic microchannels are investigated with a lattice Boltzmann model. Typical characters of the superhydrophobic phenomenon are well observed from our simulations, including air trapped in the surface microstructures, high contact angles, low contact angle hysteresis, and reduced friction to fluid motions. Increasing the roughness of a hydrophobic surface can produce a large flow rate through the channel due to the trapped air, implying less friction or large apparent slip. The apparent slip length appears to be independent to the channel width and could be considered as a surface property. For a moving droplet, its behavior is affected by the surface roughness from two aspects: the contact angle difference between its two ends and the surface-liquid interfacial friction. As a consequence, the resulting droplet velocity changes with the surface roughness as firstly decreasing and then increasing. Simulation results are also compared with experimental observations and better agreement has been obtained than that from other numerical method. The information from this study could be valuable for microfluidic systems.

scholarly journals Biomimetic Approach for the Elaboration of Highly Hydrophobic Surfaces: Study of the Links between Morphology and Wettability

Biomimetics ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 38
Author(s):  
Quentin Legrand ◽  
Stephane Benayoun ◽  
Stephane Valette
Keyword(s):  
Contact Angle ◽  
Ginkgo Biloba ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Textured Surfaces ◽  
Replication Process ◽  
Wetting Behavior ◽  
Static Contact ◽  
Biomimetic Approach ◽  
Highly Hydrophobic

This investigation of morphology-wetting links was performed using a biomimetic approach. Three natural leaves’ surfaces were studied: two bamboo varieties and Ginkgo Biloba. Multiscale surface topographies were analyzed by SEM observations, FFT, and Gaussian filtering. A PDMS replicating protocol of natural surfaces was proposed in order to study the purely morphological contribution to wetting. High static contact angles, close to 135∘, were measured on PDMS replicated surfaces. Compared to flat PDMS, the increase in static contact angle due to purely morphological contribution was around 20∘. Such an increase in contact angle was obtained despite loss of the nanometric scale during the replication process. Moreover, a significant decrease of the hysteresis contact angle was measured on PDMS replicas. The value of the contact angle hysteresis moved from 40∘ for flat PDMS to less than 10∘ for textured replicated surfaces. The wetting behavior of multiscale textured surfaces was then studied in the frame of the Wenzel and Cassie–Baxter models. Whereas the classical laws made it possible to describe the wetting behavior of the ginkgo biloba replications, a hierarchical model was developed to depict the wetting behavior of both bamboo species.

The Surface Modification with Fluorocarbon Thin Films for the Prevention of Stiction in Mems

1998 ◽  
Vol 518 ◽  
Author(s):  
Sang-Ho Lee ◽  
Myong-Jong Kwon ◽  
Jin-Goo Park ◽  
Yong-Kweon Kim ◽  
Hyung-Jae Shin
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Fluorocarbon Films ◽  
Perfluorodecanoic Acid ◽  
Large Hysteresis ◽  
Static Contact ◽  
Receding Contact ◽  
Highly Hydrophobic ◽  
Receding Contact Angle

AbstractHighly hydrophobic fluorocarbon films were prepared by the vapor phase (VP) deposition method in a vacuum chamber using both liquid (3M's FC40, FC722) and solid sources (perfluorodecanoic acid (CF3(CF2)8COOH), perfluorododecane (C12F26)) on Al, Si and oxide coated wafers. The highest static contact angles of water were measured on films deposited on aluminum substrate. But relatively lower contact angles were obtained on the films on Si and oxide wafers. The advancing and receding contact angle analysis using a captive drop method showed a large contact angle hysteresis (ΔH) on the VP deposited fluorocarbon films. AFM study showed poor film coverage on the surface with large hysteresis. FTIR-ATR analysis positively revealed the stretching band of CF2 groups on the VP deposited substrates. The thermal stability of films was measured at 150°C in air and nitrogen atmospheres as a function of time. The rapid decrease of contact angles was observed on VP deposited FC and PFDA films in air. However, no decrease of contact angle on them was observed in N2.

scholarly journals Amphiphobic Nanostructured Coatings for Industrial Applications

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 787 ◽  
Author(s):  
Federico Veronesi ◽  
Giulio Boveri ◽  
Mariarosa Raimondo
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Friction Reduction ◽  
Hybrid Coatings ◽  
Wetting Behavior ◽  
Wide Range ◽  
Solid Liquid

The search for surfaces with non-wetting behavior towards water and low-surface tension liquids affects a wide range of industries. Surface wetting is regulated by morphological and chemical features interacting with liquid phases under different ambient conditions. Most of the approaches to the fabrication of liquid-repellent surfaces are inspired by living organisms and require the fabrication of hierarchically organized structures, coupled with low surface energy chemical composition. This paper deals with the design of amphiphobic metals (AM) and alloys by deposition of nano-oxides suspensions in alcoholic or aqueous media, coupled with perfluorinated compounds and optional infused lubricant liquids resulting in, respectively, solid–liquid–air and solid–liquid–liquid working interfaces. Nanostructured organic/inorganic hybrid coatings with contact angles against water above 170°, contact angle with n-hexadecane (surface tension γ = 27 mN/m at 20 °C) in the 140–150° range and contact angle hysteresis lower than 5° have been produced. A full characterization of surface chemistry has been undertaken by X-ray photoelectron spectroscopy (XPS) analyses, while field-emission scanning electron microscope (FE-SEM) observations allowed the estimation of coatings thicknesses (300–400 nm) and their morphological features. The durability of fabricated amphiphobic surfaces was also assessed with a wide range of tests that showed their remarkable resistance to chemically aggressive environments, mechanical stresses and ultraviolet (UV) radiation. Moreover, this work analyzes the behavior of amphiphobic surfaces in terms of anti-soiling, snow-repellent and friction-reduction properties—all originated from their non-wetting behavior. The achieved results make AM materials viable solutions to be applied in different sectors answering several and pressing technical needs.

Dynamic contact angles and contact angle hysteresis

1977 ◽  
Vol 62 (2) ◽  
pp. 205-212 ◽  
Author(s):  
Rulon E Johnson ◽  
Robert H Dettre ◽  
Dale A Brandreth
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Dynamic Contact ◽  
Contact Angles

scholarly journals The Possibility of Changing the Wettability of Material Surface by Adjusting Gravity

Research ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Yong-Ming Liu ◽  
Zi-Qing Wu ◽  
Sheng Bao ◽  
Wei-Hong Guo ◽  
Da-Wei Li ◽  
...  
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Region ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Angle Measurement ◽  
Measured Parameter ◽  
Material Surface ◽  
Vapor Interface ◽  
Liquid Vapor

The contact angle, as a vital measured parameter of wettability of material surface, has long been in dispute whether it is affected by gravity. Herein, we measured the advancing and receding contact angles on extremely low contact angle hysteresis surfaces under different gravities (1-8G) and found that both of them decrease with the increase of the gravity. The underlying mechanism is revealed to be the contact angle hysteresis and the deformation of the liquid-vapor interface away from the solid surface caused by gradient distribution of the hydrostatic pressure. The real contact angle is not affected by gravity and cannot measured by an optical method. The measured apparent contact angles are angles of inclination of the liquid-vapor interface away from the solid surface. Furthermore, a new equation is proposed based on the balance of forces acting on the three-phase contact region, which quantitatively reveals the relation of the apparent contact angle with the interfacial tensions and gravity. This finding can provide new horizons for solving the debate on whether gravity affects the contact angle and may be useful for the accurate measurement of the contact angle and the development of a new contact angle measurement system.

Degradation of Hydrophobic Surface Coatings Under Water Exposure

2018 ◽  
Author(s):  
Matthew A. Trapuzzano ◽  
Rasim Guldiken ◽  
Andrés Tejada-Martínez ◽  
Nathan B. Crane
Keyword(s):  
Contact Angle ◽  
Material Selection ◽  
Contact Angle Hysteresis ◽  
Hydrophobic Surface ◽  
Contact Angles ◽  
Water Exposure ◽  
Angle Measurements ◽  
Degradation Rates ◽  
Contact Angle Measurements ◽  
Receding Contact

Many important processes depend on the wetting of liquids on surfaces. Wetting is commonly controlled through material selection, coatings, and/or surface texture, however these means are sensitive to environmental conditions. Some “hydrophobic” fluoropolymer coatings are sensitive to extended water exposure as evidenced by declining contact angles and increasing contact angle hysteresis. Understanding degradation of these coatings is critical to processes that employ them. To accomplish this, contact angle measurements were taken before, during, and after slides coated with FluoroSyl 3750 or Cytop were submerged in water, or vibrated while covered in water. Both methods demonstrated similar changes in advancing contact angle though vibration increased degradation rates significantly. However, it does not simply accelerate the process as different trends are apparent in receding contact angles. The FluoroSyl 3750 showed no clear degradation under either condition. Surface profilometry did not detect any surface morphology differences that might cause contact angle change.

Sign in / Sign up

Export Citation Format

Share Document