Phase-Inversion Poly(ether imide) Membranes Prepared from Water-Miscible/Immiscible Mixture Solvents

1999 ◽  
Vol 38 (7) ◽  
pp. 2650-2658 ◽  
Author(s):  
Jyh-Jeng Shieh ◽  
Tai-Shung Chung
Keyword(s):  
Phase Inversion ◽  
Immiscible Mixture

Phase Inversion Tape Casting and Electrochemical Performance of Solid Oxide Fuel Cell Anode

2015 ◽  
Vol 30 (12) ◽  
pp. 1291
Author(s):  
ZHANG Yu-Yue ◽  
LIN Jie ◽  
MIAO Guo-Shuan ◽  
GAO Jian-Feng ◽  
CHEN Chu-Sheng ◽  
...  
Keyword(s):  
Fuel Cell ◽  
Electrochemical Performance ◽  
Solid Oxide Fuel Cell ◽  
Phase Inversion ◽  
Tape Casting ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Cell Anode ◽  
Fuel Cell Anode

TEST-CASE NO 15: PHASE INVERSION IN A CLOSED BOX (PC)

2004 ◽  
Vol 16 (1-3) ◽  
pp. 101-104 ◽  
Author(s):  
S. Vincent ◽  
J.-P. Caltagirone ◽  
D. Jamet
Keyword(s):  
Phase Inversion ◽  
Test Case

Microporous Membranes from an Insoluble Polyimide

1995 ◽  
Vol 60 (10) ◽  
pp. 1741-1746
Author(s):  
Jan Schauer ◽  
Miroslav Marek
Keyword(s):  
Acetic Anhydride ◽  
Phase Inversion ◽  
Amic Acid ◽  
Microporous Membranes ◽  
Inversion Process ◽  
Phase Inversion Process ◽  
Ultrafiltration Process

Poly(amic acid) prepared from 3,3',4,4'-benzophenonetetracarboxylic dianhydride and bis(4-aminophenyl) ether was used for preparation of microporous membranes by the phase inversion process. Membranes coagulated in acetic anhydride were brittle but usable for ultrafiltration. Coagulation of the poly(amic acid) in water or lower alcohols and subsequent thermal cyclocondensation led to extremely brittle polyimides, which limits their use for ultrafiltration process.

Phase Inversion in Two-Phase Liquid Systems

1992 ◽  
Vol 57 (7) ◽  
pp. 1419-1423
Author(s):  
Jindřich Weiss
Keyword(s):  
Interfacial Tension ◽  
Phase Inversion ◽  
Continuous Phase ◽  
Considerable Effect ◽  
Weak Dependence ◽  
Dispersed Phase ◽  
Two Phase ◽  
Liquid Systems ◽  
Phase Liquid

New data on critical holdups of dispersed phase were measured at which the phase inversion took place. The systems studied differed in the ratio of phase viscosities and interfacial tension. A weak dependence was found of critical holdups on the impeller revolutions and on the material contactor; on the contrary, a considerable effect of viscosity was found out as far as the viscosity of continuous phase exceeded that of dispersed phase.

scholarly journals Modification of PLA Scaffold Surface for Medical Applications

2021 ◽  
Vol 11 (4) ◽  
pp. 1815
Author(s):  
Michał Młotek ◽  
Agnieszka Gadomska-Gajadhur ◽  
Aleksandra Sobczak ◽  
Aleksandra Kruk ◽  
Michalina Perron ◽  
...  
Keyword(s):  
Dielectric Barrier Discharge ◽  
Phase Inversion ◽  
Barrier Discharge ◽  
Polar Component ◽  
Medical Applications ◽  
Specific Chemical ◽  
Dielectric Barrier ◽  
Angle Measurements ◽  
Wet Phase Inversion ◽  
Materials Used

Materials used for medical applications (e.g., the cellular scaffold) should have not only the specific chemical composition, but the surface layer properties as well. For this reason, a method which enables an increase in the number of pores, wettability of the surface, and improvement the conditions of nutrient transportation into the membrane is being studied. The plasma of a dielectric barrier discharge was applied for the surface modification of polylactide obtained by dry or wet phase inversion. The plasma-modified surface was analyzed by contact angle measurements with water and diiodomethane. The surface free energy (SFE) was calculated by the Owens–Wendt method. The highest SFE and its polar component (67.6 mJ/m2 and 39.5 mJ/m2, respectively) were received when the process was conducted in an Ar + CO2 gas mixture with a discharge power of 20 W. The purpose of this research was to increase the wettability and porosity of the membrane’s surface. It can be concluded that the dielectric barrier discharge can effectively change the surface of the polylactide membranes, and that the structure of the modified membranes was not damaged during modification. The process of modification was easier for the membranes made by dry phase inversion. These materials had higher SFE values after the modification.

scholarly journals Catastrophic Phase Inversion in High-Reynolds-Number Turbulent Taylor-Couette Flow

2021 ◽  
Vol 126 (6) ◽  
Author(s):  
Dennis Bakhuis ◽  
Rodrigo Ezeta ◽  
Pim A. Bullee ◽  
Alvaro Marin ◽  
Detlef Lohse ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Couette Flow ◽  
Phase Inversion ◽  
High Reynolds Number ◽  
Taylor Couette ◽  
High Reynolds ◽  
Taylor Couette Flow

Fabrication of the narrow size nano curcuminoids emulsion by combining phase inversion temperature and ultrasonication: preparation and bioactivity

2021 ◽  
Author(s):  
Quang Hieu Tran ◽  
Thuy Thanh Ho ◽  
Tu Thanh Nguyen
Keyword(s):  
Energy Method ◽  
Phase Inversion ◽  
Curcuma Longa ◽  
High Energy ◽  
Low Energy ◽  
Inversion Temperature ◽  
Comprehensive Study ◽  
Phase Inversion Temperature

A comprehensive study from Curcuma longa to powder nano curcuminoids has been carried out. Combining of both low energy method (Phase Inversion Temperature) and high-energy method (Ultrasonication), a series of...

Sign in / Sign up

Export Citation Format

Share Document