Facile Fabrication of Multilayer Stretchable Electronics via a Two-mode Mechanical Cutting Process

ACS Nano ◽  
2021 ◽  
Author(s):  
Renxiao Xu ◽  
Peisheng He ◽  
Guangchen Lan ◽  
Kamyar Behrouzi ◽  
Yande Peng ◽  
...  
Keyword(s):  
Cutting Process ◽  
Stretchable Electronics ◽  
Facile Fabrication ◽  
Mechanical Cutting

Toward Data Assimilation in Mechanical Cutting Process

2019 ◽  
Vol 2019.32 (0) ◽  
pp. 248
Author(s):  
Takashi MISAKA ◽  
Jonny HERWAN ◽  
Oleg RYABOV ◽  
Seisuke KANO ◽  
Hiroyuki SAWADA ◽  
...  
Keyword(s):  
Data Assimilation ◽  
Cutting Process ◽  
Mechanical Cutting

Multiparameter modelling and analysis of mechanical cutting process of grain oriented silicon steel.

2021 ◽  
pp. 1-1
Author(s):  
Szymon Gontarz ◽  
Przemyslaw Szulim ◽  
Radoslaw Patyk ◽  
Lukasz Bohdal
Keyword(s):  
Silicon Steel ◽  
Cutting Process ◽  
Mechanical Cutting

Mechanical Cutting Process Trends for Difficult-to-Cut Materials : A Review

2018 ◽  
Vol 35 (3) ◽  
pp. 253-267 ◽  
Author(s):  
Myeong Gu Gang ◽  
Gyuho Kim ◽  
Kangwoo Shin ◽  
Anmok Jeong ◽  
Hyo-Young Kim ◽  
...  
Keyword(s):  
Cutting Process ◽  
Mechanical Cutting ◽  
Process Trends

Mechanical Cutting Process of Cutting Robot Based on CAD/CAM Integrated System

2014 ◽  
Vol 716-717 ◽  
pp. 1666-1670
Author(s):  
Jiu Nan Xu ◽  
Zhi Xin Hu ◽  
Ling Xiao Weng
Keyword(s):  
Integrated Control ◽  
Control Process ◽  
Integrated System ◽  
Cutting Process ◽  
Machining Process ◽  
Machining Accuracy ◽  
Cad Cam ◽  
Robot Machining ◽  
Mechanical Cutting ◽  
Cutting Path

Control problem of mechanical cutting is a development bottleneck of processing technology of robot. As compared to the simple mechanical process, the control process of automatic processing trajectory for cutting robot is relatively complex. This paper uses the CAD/CAM integrated control system to control the robot cutting process, which realizes the integration design of robot machining process. The extraction of G code is through the VC program, and then it uses MATLAB to do data analysis, which completes the design of process parameter for cutting path. Finally we use ADAMS simulation to forecaster the process parameters and machining process, through the analysis of the data it improves the machining accuracy. And it provides a theoretical reference for the research on mechanical automation process.

APPLICATION OF CASCADE REFRIGERATION SYSTEM WITH MIXING REFRIGERANT IN COLD AIR CUTTING

2005 ◽  
Vol 19 (01n03) ◽  
pp. 521-523
Author(s):  
Y. YANG ◽  
M. W. TONG ◽  
G. YANG ◽  
X. P. WANG
Keyword(s):  
High Efficiency ◽  
Cutting Process ◽  
Refrigeration System ◽  
Cascade System ◽  
Cold Air ◽  
High Efficient ◽  
Cascade Refrigeration System ◽  
Cascade Refrigeration ◽  
Mechanical Cutting ◽  
Optimal Mixing

In the mechanical cutting process, the replacement of traditional cutting solution with cold air can avoid the pollution of environment. In order to high efficient the refrigerating device and flexible adjust the temperature of cold air, it is necessary to use cascade refrigeration system to supply cool quantity for the compressed air. The introduction of a two-component non-azeotropic mixing refrigerant into the cryogenic part of the cascade system, can effectively solve the problems of the system working at too high pressure and the volume expanding of refrigerant in case of the cascade refrigeration sets closed down. However, the filling ratio of mixing refrigerants impact on the relationships among the closing down pressure, refrigerating output and refrigerating efficiency. On the basis of computing and experiment, the optimal mixing ratio of refrigerant R22/R13 and a low temperature of -60° were obtained in this study. A cold air injecting device possessing high efficiency in energy saving has also been designed and manufactured. The cold air, generated from this cascade system and employed in a cutting process, takes good comprehensive effects on machining and cutting.

scholarly journals Facile Fabrication of Stretchable Electrodes by Sedimentation of Ag Nanoparticles in PDMS Matrix

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Jae-Yeop Kim ◽  
Kwang-Suk Jang
Keyword(s):  
Electrical Conductivity ◽  
Ag Nanoparticles ◽  
High Performance ◽  
Surface Resistance ◽  
Volume Fraction ◽  
Stretchable Electronics ◽  
Fabrication Method ◽  
Composite Surface ◽  
Local Volume ◽  
Facile Fabrication

This study reports a facile fabrication method for highly conductive stretchable electrodes composed of a conductive 0D nanomaterial filler and an elastomer matrix. The local volume fraction of the Ag nanoparticles at the composite surface could be significantly increased by the sedimentation of Ag nanoparticles in uncured polydimethylsiloxane (PDMS) fluid. The stretchable electrodes had a surface resistance of 0.910±0.509 Ω/sq and were stretchable up to 100% of strain without the reduction of the electrical conductivity, demonstrating their potential as high-performance electrodes for applications in stretchable electronics.

scholarly journals Multiparameter Optimization of Mechanical Cutting Process of Grain Oriented Silicon Steel

2020 ◽  
Vol 137 (5) ◽  
pp. 930-932
Author(s):  
S. Gontarz ◽  
R. Patyk ◽  
L. Bohdal ◽  
D. Jackiewicz
Keyword(s):  
Silicon Steel ◽  
Cutting Process ◽  
Multiparameter Optimization ◽  
Mechanical Cutting

Method to evaluate residual stresses in the laser cutting process

2002 ◽  
Vol 12 (1) ◽  
pp. 27-41 ◽  
Author(s):  
Y. Zamachtchikov ◽  
F. Breaban ◽  
P. Vantomme ◽  
A. Deffontaine
Keyword(s):  
Residual Stresses ◽  
Laser Cutting ◽  
Cutting Process

Facile fabrication of ZrO 2 @PMMA@polysiloxane nanohybrids and their application for light diffusing films

2019 ◽  
Vol 14 (4) ◽  
pp. 349-352
Author(s):  
Xiaohai Bu ◽  
Dongxian Li ◽  
Zewu Zhang ◽  
Chaofeng Hong ◽  
Li Zhang ◽  
...  
Keyword(s):  
Facile Fabrication
Sign in / Sign up

Export Citation Format

Share Document