scholarly journals Surface Conditions That Constrain Alkane Oxidation on Perovskites

ACS Catalysis ◽  
2020 ◽  
Vol 10 (13) ◽  
pp. 7007-7020 ◽  
Author(s):  
Gregor Koch ◽  
Michael Hävecker ◽  
Detre Teschner ◽  
Spencer J. Carey ◽  
Yuanqing Wang ◽  
...  
Keyword(s):  
Alkane Oxidation ◽  
Surface Conditions

The oxidation of Inconel alloy MA754 at low oxidation potential

1983 ◽  
Vol 41 ◽  
pp. 218-219
Author(s):  
D. N. Braski ◽  
P. D. Goodell ◽  
J. V. Cathcart ◽  
R. H. Kane
Keyword(s):  
Surface Layer ◽  
Oxidation Potential ◽  
Metal Interface ◽  
Elevated Temperature Strength ◽  
Surface Conditions ◽  
Inconel Alloy ◽  
Inco Alloy ◽  
Resistance To Oxidation ◽  
Oxide Particles ◽  
Cold Worked

It has been known for some time that the addition of small oxide particles to an 80 Ni—20 Cr alloy not only increases its elevated-temperature strength, but also markedly improves its resistance to oxidation. The mechanism by which the oxide dispersoid enhances the oxidation resistance is being studied collaboratively by ORNL and INCO Alloy Products Company.Initial experiments were performed using INCONEL alloy MA754, which is nominally: 78 Ni, 20 Cr, 0.05 C, 0.3 Al, 0.5 Ti, 1.0 Fe, and 0.6 Y2O3 (wt %).Small disks (3 mm diam × 0.38 mm thick) were cut from MA754 plate stock and prepared with two different surface conditions. The first was prepared by mechanically polishing one side of a disk through 0.5 μm diamond on a syntron polisher while the second used an additional sulfuric acid-methanol electropolishing treatment to remove the cold-worked surface layer. Disks having both surface treatments were oxidized in a radiantly heated furnace for 30 s at 1000°C. Three different environments were investigated: hydrogen with nominal dew points of 0°C, —25°C, and —55°C. The oxide particles and films were examined in TEM by using extraction replicas (carbon) and by backpolishing to the oxide/metal interface. The particles were analyzed by EDS and SAD.

EFFECT OF SURFACE CONDITIONS ON COERCIVITIES FOR Nd-Fe-B MAGNETS

1988 ◽  
Vol 49 (C8) ◽  
pp. C8-641-C8-642
Author(s):  
Y. Otani ◽  
H. Miyajima ◽  
S. Chikazumi ◽  
S. Hirosawa ◽  
M. Sagawa
Keyword(s):  
Surface Conditions ◽  
Effect Of Surface

scholarly journals A Newn-Alkane Oxidation System fromPseudomonas aeruginosaS7B1

1981 ◽  
Vol 45 (1) ◽  
pp. 9-14
Author(s):  
Hidetoshi Matsuyama ◽  
Tadaatsu Nakahara ◽  
Yasuji Minoda
Keyword(s):  
Alkane Oxidation ◽  
Oxidation System

scholarly journals Spectral albedo of coastal landfast sea ice in Prydz Bay, Antarctica

2020 ◽  
pp. 1-11
Author(s):  
Guanghua Hao ◽  
Roberta Pirazzini ◽  
Qinghua Yang ◽  
Zhongxiang Tian ◽  
Changwei Liu
Keyword(s):  
Sea Ice ◽  
Near Infrared ◽  
Elevation Angle ◽  
Early Summer ◽  
Prydz Bay ◽  
Katabatic Wind ◽  
Surface Conditions ◽  
Zhongshan Station ◽  
Landfast Sea Ice ◽  
Two Phases

Abstract The surface spectral albedo was measured over coastal landfast sea ice in Prydz Bay (off Zhongshan Station), East Antarctica from 5 October to 26 November of 2016. The mean albedo decreased from late-spring to early-summer, mainly responding to the change in surface conditions from dry (phase I) to wet (phase II). The evolution of the albedo was strongly influenced by the surface conditions, with alternation of frequent snowfall events and katabatic wind that induce snow blowing at the surface. The two phases and day-to-day albedo variability were more pronounced in the near-infrared albedo wavelengths than in the visible ones, as the near-infrared photons are more sensitive to snow metamorphism, and to changes in the uppermost millimeters and water content of the surface. The albedo diurnal cycle during clear sky conditions was asymmetric with respect to noon, decreasing from morning to evening over full and patchy snow cover, and decreasing more rapidly in the morning over bare ice. We conclude that snow and ice metamorphism and surface melting dominated over the solar elevation angle dependency in shaping the albedo evolution. However, we realize that more detailed surface observations are needed to clarify and quantify the role of the various surface processes.

Sign in / Sign up

Export Citation Format

Share Document