In-Operando AFM Characterization of Mechanical Property Evolution of Si Anode Binders in Liquid Electrolyte

2020 ◽  
Vol 3 (2) ◽  
pp. 1899-1907 ◽  
Author(s):  
Michael Lee ◽  
Rahul Kumar Raghava Reddi ◽  
Junbin Choi ◽  
Jian Liu ◽  
Xiaosong Huang ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Liquid Electrolyte ◽  
Si Anode ◽  
In Operando

Mechanical property and characterization of 7A04-T6 aluminum alloys bonded by friction stir welding

2020 ◽  
Vol 52 ◽  
pp. 263-269 ◽  
Author(s):  
Jianing Li ◽  
Molin Su ◽  
Wenjun Qi ◽  
Chen Wang ◽  
Peng Zhao ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Friction Stir

Mechanical property characterization of mouse zona pellucida

2003 ◽  
Vol 2 (4) ◽  
pp. 279-286 ◽  
Author(s):  
Yu Sun ◽  
Kai-Tak Wan ◽  
K.P. Roberts ◽  
J.C. Bischof ◽  
B.J. Nelson
Keyword(s):  
Mechanical Property ◽  
Zona Pellucida ◽  
Property Characterization

Characterization of mechanical property of magnesium AZ31 alloy sheets for warm temperature forming

2015 ◽  
Vol 93 ◽  
pp. 204-217 ◽  
Author(s):  
Youngwoo Koh ◽  
Daeyong Kim ◽  
Dong-Yoon Seok ◽  
Jeonghwan Bak ◽  
Sang-Woo Kim ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Az31 Alloy ◽  
Warm Temperature ◽  
Magnesium Az31

Mechanical Property and Oxidation Behavior of LPS-SiC Materials

2006 ◽  
Vol 321-323 ◽  
pp. 913-916
Author(s):  
Sang Ll Lee ◽  
Yun Seok Shin ◽  
Jin Kyung Lee ◽  
Jong Baek Lee ◽  
Jun Young Park
Keyword(s):  
Mechanical Property ◽  
Fracture Toughness ◽  
Oxidation Behavior ◽  
Elevated Temperatures ◽  
Indentation Test ◽  
Bending Test ◽  
Secondary Phases ◽  
Three Point Bending ◽  
Different Temperatures

The microstructure and the mechanical property of liquid phase sintered (LPS) SiC materials with oxide secondary phases have been investigated. The strength variation of LPS-SiC materials exposed at the elevated temperatures has been also examined. LPS-SiC materials were sintered at the different temperatures using two types of Al2O3/Y2O3 compositional ratio. The characterization of LPS-SiC materials was investigated by means of SEM with EDS, three point bending test and indentation test. The LPS-SiC material with a density of about 3.2 Mg/m3 represented a flexural strength of about 800 MPa and a fracture toughness of about 9.0 MPa⋅√m.

scholarly journals Solidifying behavior and Characterization of Al (LM6) +SICP Metal Matrix Composites

2019 ◽  
Vol 8 (6) ◽  
pp. 2397-2403 ◽  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Cooling Rate ◽  
Metal Matrix Composite ◽  
Metal Matrix ◽  
Matrix Composites ◽  
Liquid Temperature ◽  
Step Size ◽  
Different Parts

This paper presents the investigation of moderate properties of solidified Al (LM6)+SiCp metal matrix composite (AMMC). These AMMC is fabricated by considering five different parts of casting and different weight of SiCp for reinforcement. The SiCp wt. % is varied from 5 wt. % to 15 wt. % with a step size 5 %. During casting, temperature is measured using K-thermocouple and temperature vs. solidification curve is traced. These results are compared with the solidification results of Al (LM6) alloy. It is observed that the solidifying duration of AMMC increased as well as decreased liquid temperature by adding SiCp to it. The trend of the curve is also presented that the cooling rate and the duration of solidification are different for different part of casting. Mechanical property of the each five parts of casting is tabulated. It is observed from the properties that the mechanical properties of AMMC increased by increasing the wt. % of the reinforced particles SiCp.

Sign in / Sign up

Export Citation Format

Share Document