scholarly journals Interparticle Adhesion Regulates the Surface Roughness of Growing Dense Three-Dimensional Active Particle Aggregates

2021 ◽  
Author(s):  
Sumit Sinha ◽  
Abdul N Malmi-Kakkada
Keyword(s):  
Surface Roughness ◽  
Three Dimensional ◽  
Active Particle ◽  
Particle Aggregates

Enhancement of Heat Transfer Performance in Nuclear Fuel Rod Using Nanofluids and Surface Roughness Technique

2015 ◽  
Author(s):  
Kang Liu ◽  
Titan C. Paul ◽  
Leo A. Carrilho ◽  
Jamil A. Khan
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Nuclear Fuel ◽  
Three Dimensional ◽  
Pressurized Water ◽  
Bulk Fluid ◽  
Fuel Rod ◽  
Dimensional Surface

The experimental investigations were carried out of a pressurized water nuclear reactor (PWR) with enhanced surface using different concentration (0.5 and 2.0 vol%) of ZnO/DI-water based nanofluids as a coolant. The experimental setup consisted of a flow loop with a nuclear fuel rod section that was heated by electrical current. The fuel rod surfaces were termed as two-dimensional surface roughness (square transverse ribbed surface) and three-dimensional surface roughness (diamond shaped blocks). The variation in temperature of nuclear fuel rod was measured along the length of a specified section. Heat transfer coefficient was calculated by measuring heat flux and temperature differences between surface and bulk fluid. The experimental results of nanofluids were compared with the coolant as a DI-water data. The maximum heat transfer coefficient enhancement was achieved 33% at Re = 1.15 × 105 for fuel rod with three-dimensional surface roughness using 2.0 vol% nanofluids compared to DI-water.

scholarly journals Dimensional Accuracy of Dental Models for Three-Unit Prostheses Fabricated by Various 3D Printing Technologies

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1550
Author(s):  
Soo-Yeon Yoo ◽  
Seong-Kyun Kim ◽  
Seong-Joo Heo ◽  
Jai-Young Koak ◽  
Joung-Gyu Kim
Keyword(s):  
Surface Roughness ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
3D Analysis ◽  
Digital Light Processing ◽  
Test Models ◽  
Reference File ◽  
Significant Difference ◽  
Jet Printing ◽  
3D Printed

Previous studies on accuracy of three-dimensional (3D) printed model focused on full arch measurements at few points. The aim of this study was to examine the dimensional accuracy of 3D-printed models which were teeth-prepped for three-unit fixed prostheses, especially at margin and proximal contact areas. The prepped dental model was scanned with a desktop scanner. Using this reference file, test models were fabricated by digital light processing (DLP), Multi-Jet printing (MJP), and stereo-lithography apparatus (SLA) techniques. We calculated the accuracy (trueness and precision) of 3D-printed models on 3D planes, and deviations of each measured points at buccolingual and mesiodistal planes. We also analyzed the surface roughness of resin printed models. For overall 3D analysis, MJP showed significantly higher accuracy (trueness) than DLP and SLA techniques; however, there was not any statistically significant difference on precision. For deviations on margins of molar tooth and distance to proximal contact, MJP showed significantly accurate results; however, for a premolar tooth, there was no significant difference between the groups. 3D color maps of printed models showed contraction buccolingually, and surface roughness of the models fabricated by MJP technique was observed as the lowest. The accuracy of the 3D-printed resin models by DLP, MJP, and SLA techniques showed a clinically acceptable range to use as a working model for manufacturing dental prostheses

A test of airborne, side-looking synthetic-aperture radar in central Newfoundland for geological reconnaissance

1991 ◽  
Vol 28 (2) ◽  
pp. 257-265 ◽  
Author(s):  
D. F. Graham ◽  
D. R. Grant
Keyword(s):  
Surface Roughness ◽  
Synthetic Aperture Radar ◽  
Three Dimensional ◽  
Synthetic Aperture ◽  
Structural Elements ◽  
Terrain Classification ◽  
Regional Trends ◽  
Valuable Complement ◽  
Wide Swath ◽  
Aperture Radar

Side-looking, C-band synthetic-aperture radar (SAR) penetrates cloud and fog, and operates day or night, to produce pseudo-three-dimensional terrain images with enhanced topography and surface roughness. The images, which have a 20 m resolution and cover large areas, have been used to map the regional trends, patterns of lineaments, and terrain types over a 6200 km2 area of complex lithology, structure, and drift cover. Four lineament classes are differentiated. Glacial trends are clear, and bedrock structures (faults, fractures, joints, foliation, and folded bedding) with relief expression at the surface show through the drift as lineaments. They accurately reproduce most known features when compared with bedrock and Quatenary geology maps. Hitherto unrecognized structural elements are revealed. Tones and textures reflect minute surface roughness variations useful in terrain classification. SAR wide-swath-mode imagery is thus a valuable complement to aerial photography, and is superior in revealing hummocky moraine, ribbed moraine, boulder fields and stony till. Wider use of this imagery is encouraged.

Acoustic receptivity and evolution of two-dimensional and oblique disturbances in a Blasius boundary layer

2001 ◽  
Vol 432 ◽  
pp. 69-90 ◽  
Author(s):  
RUDOLPH A. KING ◽  
KENNETH S. BREUER
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Acoustic Wave ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Surface Waviness ◽  
S Wave ◽  
Boundary Layer Instability ◽  
Blasius Boundary Layer ◽  
Tollmien Schlichting

An experimental investigation was conducted to examine acoustic receptivity and subsequent boundary-layer instability evolution for a Blasius boundary layer formed on a flat plate in the presence of two-dimensional and oblique (three-dimensional) surface waviness. The effect of the non-localized surface roughness geometry and acoustic wave amplitude on the receptivity process was explored. The surface roughness had a well-defined wavenumber spectrum with fundamental wavenumber kw. A planar downstream-travelling acoustic wave was created to temporally excite the flow near the resonance frequency of an unstable eigenmode corresponding to kts = kw. The range of acoustic forcing levels, ε, and roughness heights, Δh, examined resulted in a linear dependence of receptivity coefficients; however, the larger values of the forcing combination εΔh resulted in subsequent nonlinear development of the Tollmien–Schlichting (T–S) wave. This study provides the first experimental evidence of a marked increase in the receptivity coefficient with increasing obliqueness of the surface waviness in excellent agreement with theory. Detuning of the two-dimensional and oblique disturbances was investigated by varying the streamwise wall-roughness wavenumber αw and measuring the T–S response. For the configuration where laminar-to-turbulent breakdown occurred, the breakdown process was found to be dominated by energy at the fundamental and harmonic frequencies, indicative of K-type breakdown.

Color Reproduction Accuracy Promotion of 3D-Printed Surfaces Based on Microscopic Image Analysis

2019 ◽  
Vol 34 (01) ◽  
pp. 2054004 ◽  
Author(s):  
Xiaochun Wang ◽  
Chen Chen ◽  
Jiangping Yuan ◽  
Guangxue Chen
Keyword(s):  
Surface Roughness ◽  
Image Analysis ◽  
Three Dimensional ◽  
Prediction Method ◽  
Chromatic Aberration ◽  
Optimization Methods ◽  
Experimental Models ◽  
Microscopic Image ◽  
Color Reproduction ◽  
Microscopic Image Analysis

Full-color three-dimensional (3D) printing technology is a powerful process to manufacture intelligent customized colorful objects with improved surface qualities; however, poor surface color optimization methods are the main impeding factors for its commercialization. As such, the paper explored the correlation between microstructure and color reproduction, then an assessment and prediction method of color optimization based on microscopic image analysis was proposed. The experimental models were divided into 24-color plates and 4-color cubes printed by ProJet 860 3D printer, then impregnated according to preset parameters, at last measured by a spectrophotometer and observed using both a digital microscope and a scanning electron microscope. The results revealed that the samples manifested higher saturation and smaller chromatic aberration ([Formula: see text]) after postprocessing. Moreover, the brightness of the same color surface increased with the increasing soaked surface roughness. Further, reduction in surface roughness, impregnation into surface pores, and enhancement of coating transparency effectively improved the accuracy of color reproduction, which could be verified by the measured values. Finally, the chromatic aberration caused by positioning errors on different faces of the samples was optimized, and the value of [Formula: see text] for a black cube was reduced from 8.12 to 0.82, which is undetectable to human eyes.

Simulation of Plasto-Elastohydrodynamic Lubrication in Line Contacts of Infinite and Finite Length

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Tao He ◽  
Jiaxu Wang ◽  
Zhanjiang Wang ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Finite Length ◽  
3D Model ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Axial Direction ◽  
Contact Length ◽  
Line Contact ◽  
Line Contacts ◽  
3D Surface Topography

Line contact is common in many machine components, such as various gears, roller and needle bearings, and cams and followers. Traditionally, line contact is modeled as a two-dimensional (2D) problem when the surfaces are assumed to be smooth or treated stochastically. In reality, however, surface roughness is usually three-dimensional (3D) in nature, so that a 3D model is needed when analyzing contact and lubrication deterministically. Moreover, contact length is often finite, and realistic geometry may possibly include a crowning in the axial direction and round corners or chamfers at two ends. In the present study, plasto-elastohydrodynamic lubrication (PEHL) simulations for line contacts of both infinite and finite length have been conducted, taking into account the effects of surface roughness and possible plastic deformation, with a 3D model that is needed when taking into account the realistic contact geometry and the 3D surface topography. With this newly developed PEHL model, numerical cases are analyzed in order to reveal the PEHL characteristics in different types of line contact.

EFFECT OF ABRASIVE TYPE ON THE SURFACE ROUGHNESS AND MRR IN MAF OF AISI 304 STEEL

2021 ◽  
Author(s):  
MAHMUT ÇELIK ◽  
HAKAN GÜRÜN ◽  
ULAŞ ÇAYDAŞ
Keyword(s):  
Surface Roughness ◽  
Removal Rate ◽  
Three Dimensional ◽  
Steel Plates ◽  
304 Stainless Steel ◽  
Average Surface Roughness ◽  
Machining Time ◽  
Aisi 304 ◽  
Average Surface ◽  
Different Levels

In this study, the effects of experimental parameters on average surface roughness and material removal rate (MRR) were experimentally investigated by machining of AISI 304 stainless steel plates by magnetic abrasive finishing (MAF) method. In the study in which three different abrasive types were used (Al2O3, B4C, SiC), the abrasive grain size was changed in two different levels (50 and 80[Formula: see text][Formula: see text]m), while the machining time was changed in three different levels (30, 45, 60[Formula: see text]min). Surface roughness values of finished surfaces were measured by using three-dimensional (3D) optical surface profilometer and surface topographies were created. MRRs were measured with the help of precision scales. The abrasive particles’ condition before and after the MAF process was examined and compared using a scanning electron microscope. As a result of the study, the surface roughness values of plates were reduced from 0.106[Formula: see text][Formula: see text]m to 0.028[Formula: see text][Formula: see text]m. It was determined that the best parameters in terms of average surface roughness were 60[Formula: see text]min machining time with 50[Formula: see text][Formula: see text]m B4C abrasives, while the best result in terms of MRR was taken in 30[Formula: see text]min with 50[Formula: see text][Formula: see text]m SiC abrasives.

Obtaining the thermal resistance of air enclosed at the interface of multilayer fabrics by simulation

2018 ◽  
Vol 89 (15) ◽  
pp. 3178-3188 ◽  
Author(s):  
Hua Shen ◽  
Lexi Tu ◽  
Xiaofei Yan ◽  
Sachiko Sukigara
Keyword(s):  
Finite Element Method ◽  
Surface Roughness ◽  
Thermal Resistance ◽  
Three Dimensional ◽  
Estimating Equation ◽  
Experimental Result ◽  
Dimensional Finite Element ◽  
Experimental Values ◽  
Three Dimensional Finite Element ◽  
Method Model

An air layer enclosed at the interface was largely responsible for the insulation results of multilayer fabrics obtained from experiments. In this study, a three-dimensional finite element method model, in which the air layer enclosed at the interface of multilayer fabrics was ignored, was developed to calculate the fabric thermal resistance, and the result obtained from the fabric model was independent of the air. A Thermolab II Tester KES-F7 was also used to measure the thermal resistance of fabrics, and the experimental results were influenced by the air layer. By comparing the simulation and experimental result, the air layer thermal resistance was determined, and then an estimating equation, which can be used to estimate the fabric and air layer thermal resistance for multilayer fabrics, was proposed. The results suggested that the surface roughness of fabrics was strongly related to the air layer thermal resistance, with a linear relationship between them. Moreover, for multiple layers stacked by different fabrics, the air layer thermal resistance at the interface was mainly decided by the fabric with the rougher surface. An estimating equation was also developed to predict the thermal resistance of multilayer fabrics and good correlation between predicted and experimental values was observed.

Sign in / Sign up

Export Citation Format

Share Document