Determination of temperature rise time and temperature profiles for three commercial pyrolyzer sample holders

1982 ◽  
Vol 54 (14) ◽  
pp. 2620-2622 ◽  
Author(s):  
John J. R. Mertens ◽  
Eddy. Jacobs ◽  
Andre J. A. Callaerts ◽  
A. Buekens
Keyword(s):  
Temperature Rise ◽  
Rise Time ◽  
Temperature Profiles

Cathodoluminescence of SiO2/Si System

2009 ◽  
Vol 156-158 ◽  
pp. 487-492 ◽  
Author(s):  
M.V. Zamoryanskaya
Keyword(s):  
Activation Energy ◽  
Electron Beam ◽  
Rise Time ◽  
Silicon Oxide ◽  
Beam Current ◽  
Electron Beam Current ◽  
Electron Traps ◽  
Definition Of ◽  
Luminescent Centers

In this paper the new method for determination of luminescent centers concentration are discussed. While the possibility of electron traps determination and definition of its activation energy are suggested. The cathodoluminescent (CL) method was used. The determination of luminescent centers concentration in silicon oxide is based on the measurements of dependences of CL intensity on electron beam current. The presence and energy of activation of electron traps were studied by measurement of rise time and decay of luminescent band during the stationary irradiation of silica by electron beam.

Determination of source parameters of small earthquakes from P-wave rise time

1973 ◽  
Vol 63 (2) ◽  
pp. 599-614 ◽  
Author(s):  
M. E. O'Neill ◽  
J. H. Healy
Keyword(s):  
Rise Time ◽  
Source Parameters ◽  
P Wave ◽  
Simple Method ◽  
Zero Crossing ◽  
Basic Measurement ◽  
Earthquake Source Parameters ◽  
Short Period ◽  
Stress Drops

abstract A simple method of estimating source dimensions and stress drops of small earthquakes is presented. The basic measurement is the time from the first break to the first zero crossing on short-period seismograms. Graphs relating these measurements to rise time as a function of Q and instrument response permit an estimate of earthquake source parameters without the calculation of spectra. Tests on data from Rangely, Colorado, and Hollister, California, indicate that the method gives reasonable results.

scholarly journals SANDWICH PANELS – BEHAVIOR IN FIRE BASED ON FIRE RESISTANCE TESTS

2016 ◽  
Author(s):  
Paweł Roszkowski ◽  
Paweł Sulik
Keyword(s):  
Thermal Insulation ◽  
Fire Resistance ◽  
Temperature Rise ◽  
Sandwich Panel ◽  
Sandwich Panels ◽  
And Behavior ◽  
In Fire ◽  
Resistance Tests ◽  
Building Elements

<p>Sandwich panel is the material that is easy and quickly to install. Basing on a great experience in the area of determination of the fire resistance class of construction building elements the authors describe the properties and behavior of building elements made of the sandwich panels exposed to fire. The article presents the results of fire resistance tests carried out in accordance with EN 1364-1 non-bearing walls made of sandwich panels with use of different cores.</p>The following parameters were analyzed: temperature rise on unexposed side (I – thermal insulation), integrity (E) depending on the orientations and on the width of the sandwich panels, deflection depending on the thickness of the boards. Conclusions were made on the base of the analysis from fire resistance tests.

Numerical Verification of the Thermodynamic Determination of the Hydraulic Efficiency of Radial Fans

2019 ◽  
Author(s):  
Philipp Epple ◽  
Manuel Fritsche ◽  
Felix Reinker ◽  
Stefan aus der Wiesche
Keyword(s):  
Temperature Rise ◽  
Pressure Rise ◽  
Inlet Temperature ◽  
Numerical Verification ◽  
Hydraulic Efficiency ◽  
Hydraulic Power ◽  
The Real ◽  
Shaft Power ◽  
Real Temperature

Abstract For fans without cooling it is possible to determine the hydraulic efficiency measuring the pressure and the temperature rise through the fan. The shaft work can be determined according applying the first law of thermodynamics for an open system. Without any losses the change of state would be isotropic and the work done equal to the specific heat at constant pressure of the fluid times the isentropic temperature rise in the impeller. Due to the losses, however, the real temperature at the exit of the impeller will be higher than the isentropic temperature since the real process is polytropic. The isentropic temperature at the exit of the impeller can be computed by the isentropic relations with the inlet temperature and the pressure rise. The hydraulic efficiency can be computed as the ratio of the isentropic temperature rise divided by the real temperature rise. In order to verify this thermodynamic approach for the determination of the hydraulic efficiency CFD simulations of a radial fan were performed. In the CFD simulation the hydraulic power, the shaft power, the pressure rise and the temperature rise can be read out and computed directly. In such a way the hydraulic efficiency computed by the ratio of the hydraulic power by the shaft power can be compared by the thermodynamically computed efficiency. In this work this comparison has been performed and the results and the precision of the thermodynamically predicted efficiency are presented and discussed in detail.

Determination of temperature profiles in microcircuits

1962 ◽  
Author(s):  
M. Walker ◽  
J. Roschen ◽  
E. Schlegel
Keyword(s):  
Temperature Profiles
Sign in / Sign up

Export Citation Format

Share Document