scholarly journals Anti-icing performance of hydrophobic material used for electromechanical drill applied in ice core drilling

2020 ◽  
Vol 66 (258) ◽  
pp. 618-626 ◽  
Author(s):  
Pinlu Cao ◽  
Zhuo Chen ◽  
Hongyu Cao ◽  
Baoyi Chen ◽  
Zhichuan Zheng
Keyword(s):  
Shear Strength ◽  
Ice Core ◽  
Water Repellency ◽  
Contact Angles ◽  
Curved Surface ◽  
Coating Materials ◽  
Water Contact ◽  
Hydrophobic Coating ◽  
Main Challenge ◽  
Ice Adhesion

AbstractUsing an anti-icing coating to prevent ice accretion on the drill surface is a feasible solution to address the drilling difficulties in warm ice. In this study, four types of commercially available hydrophobic coating materials were tested to evaluate their water repellency and anti-icing properties, namely, a mixture of silica and fluorocarbon resin with polytrifluoroethylene, modified Teflon, silica-based emulsion and an acrylic-based copolymer. Their water contact angles are ~107°, 101°, 114° and 95°, respectively. All these hydrophobic coatings can significantly reduce the strength of the ice adhesion within a temperature range of −10 to −30°C on a planar or curved surface. The coating of an acrylic-based copolymer, in particular, can reduce the average tensile strength and the shear strength of the ice adhesion by 87.08 and 97.11% on planar surfaces at −30°C, and by 98.06 and 96.15% on a curved surface, respectively. The main challenge in the practical application of these coatings is their durability. An acrylic-based copolymer coating will lose its water repellency performance after 140 cycles of abrasion. The shear strength of ice adhered on curved surfaces coated with this material will approach that achieved on uncoated surfaces after 11 cycles of icing and de-icing tests.

scholarly journals Water modulates the lamellar structure and interlayer correlation of poly(perfluorooctyl acrylate) films: a specular and off-specular neutron scattering study

2021 ◽  
Author(s):  
Akihisa Yamamoto ◽  
Yuji Higaki ◽  
Judith Thoma ◽  
Esther Kimmle ◽  
Ryohei Ishige ◽  
...  
Keyword(s):  
Neutron Scattering ◽  
Osmotic Pressure ◽  
Correlation Length ◽  
Ethyl Acrylate ◽  
Contact Angles ◽  
Water Repellent ◽  
Water Molecules ◽  
Coating Materials ◽  
Water Contact ◽  
Vertical Correlation

AbstractComb-like polymers with pendant-like perfluorocarbon side chains self-assemble into smectic lamellae and have been extensively used as water-repellent, hydrophobic coating materials characterized by large water contact angles (θ > 120°). As poly(perfluorooctyl acrylate) films are “apparently hydrophobic” (θ > 120°), the interaction of such materials and water molecules has been largely overlooked. To unravel the molecular-level interactions between water and apparently hydrophobic polymers, specular and off-specular neutron scattering experiments were conducted at defined osmotic pressure ΠH2O. The poly{2-[(perfluorooctylethyl)carbamate]ethyl} acrylate (PFAUr-C8), which had a carbamate linker, transitioned to another lamellar phase at 89 °C. At T = 25 °C; the lamellar periodicity of PFAUr-C8 slightly increased with decreasing osmotic pressure, while the vertical correlation length increased. However, the poly[(perfluorooctyl)ethyl] acrylate (PFA-C8) that did not contain a carbamate linker directly transitioned to a disordered phase at 84 °C. The lamellar periodicity of PFA-C8 was largely independent of the osmotic pressure, suggesting that PFA-C8 was poorly hydrated. Remarkably, the vertical correlation length decreased with decreasing osmotic pressure. Because hydration facilitated by the linker modulated the smectic lamellae of the poly(perfluoroalkyl acrylate), water molecules could be used to optimize the self-assembly of apparently hydrophobic liquid crystalline polymers.

scholarly journals Crystallization Behavior of Phosphate Glasses with Hydrophobic Coating Materials

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Jaeyeop Chung ◽  
Bongki Ryu
Keyword(s):  
Crystallization Behavior ◽  
Glass Frit ◽  
Contact Angles ◽  
Exothermic Peak ◽  
Phosphate Glasses ◽  
Coating Materials ◽  
Hydrophobic Coating ◽  
Coated Surface ◽  
Diffraction Peaks ◽  
Strong Exothermic Peak

We analyzed the effect of the addition of Li2O3, TiO2, and Fe2O3on the crystallization behavior of P2O5–CaO–SiO2–K2O glasses and the effect of the crystallization behavior on the roughness and hydrophobicity of the coated surface. Exothermic behavior, including a strong exothermic peak in the 833–972 K temperature range when Fe2O3, TiO2, or Li2O3was added, was confirmed by differential thermal analysis. The modified glass samples (PFTL1–3) showed diffraction peaks when heated at 1073 and 1123 K for 5 min; the crystallized phase corresponds to Fe3(PO4)2, that is, graftonite. We confirmed that the intensity of the diffraction peaks increases at high temperatures and with increasing Li2O3content. In the case of the PFTL3 glass, a Li3Fe2(PO4)2phase, that is, trilithium diiron(III) tris[phosphate(V)], was observed. Through scanning electron microscopy and the contact angles of the surfaces with water, we confirmed that the increase in surface roughness, correlated to the crystallization of the glass frit, increases hydrophobicity of the surface. The calculated values of the local activation energies for the growth of Fe3(PO4)2on the PTFL1, PTFL2, and PFTL3 glass were 237–292 kJ mol−1, 182–258 kJ mol−1, and 180–235 kJ mol−1.

Water Shedding Properties of Oil Impregnated Hydrophobic Soils

2020 ◽  
Author(s):  
Rebecca McCerery ◽  
John Woodward ◽  
Glen McHale ◽  
Kate Winter
Keyword(s):  
Soil Water ◽  
Silicone Oil ◽  
Water Repellency ◽  
Contact Angles ◽  
Water Infiltration ◽  
Natural Soil ◽  
Particle Sizes ◽  
Soil Water Repellency ◽  
Water Contact ◽  
Naturally Occurring

<p>Hydrophobic soils and sediments have gained significant interest in soil science due to negatively influencing biomass production and as drivers of landslides and enhanced erosion. Whilst natural and fire-induced soil water repellency have been studied, little work has considered how the sediment-water interaction with naturally occurring hydrophobic sediments might change in the presence of oil. Recent advances in materials physics have shown bio-inspired slippery liquid infused porous surfaces (SLIPS) and lubricant impregnated surfaces (LIS) can produce super slippery surfaces with excellent water shedding properties. Here we apply this new understanding to the physics of soil water repellency and address how the presence of oil, whether from contamination or otherwise, might influence water infiltration. We hypothesise that oil impregnating a hydrophobic soil may create stable oil coatings and/or layers that create soil surfaces resistant to water infiltration and with enhanced run-off of water. Using monolayers of sand, silt and clay particles treated with a commercial hydrophobising agent and silicone oil, we created model (oil-free) hydrophobic and oil impregnated hydrophobic soils. Static water contact angles and droplet sliding angles were used to classify their degree of hydrophobicity and ability to shed water. Our results show that in the absence of oil, model hydrophobic soil surfaces with particle sizes below 63μm are superhydrophobic with water droplet contact angles above 150 degrees. In the presence of oil, we observed a sediment-based SLIP/LI surface on particle sizes below 63μm with water contact angles of 90 degrees and droplet sliding angles of below 5 degrees. We also achieved reduced sliding angles compared to the oil-free surfaces, and a conformal layer of oil on all particle sizes. These results support our hypothesis that SLIPS/LIS may occur in natural soil systems. These results have implications for soil water repellency, oil clean up from soil and for processes occurring in other sedimentary environments caused by both naturally occurring and anthropogenic contamination of oils.</p>

scholarly journals Fluorosilane Water-Repellent Coating for the Protection of Marble, Wood and Other Materials

Heritage ◽  
2021 ◽  
Vol 4 (4) ◽  
pp. 2668-2675
Author(s):  
Fotios G. Adamopoulos ◽  
Evangelia C. Vouvoudi ◽  
Dimitris S. Achilias ◽  
Ioannis Karapanagiotis
Keyword(s):  
Polymer Networks ◽  
Treated Wood ◽  
Water Repellency ◽  
Contact Angles ◽  
Water Repellent ◽  
Capillary Absorption ◽  
Durability Test ◽  
Water Contact ◽  
Produce Water ◽  
The Aesthetic

The preservation of cultural heritage monuments and artifacts requires the development of methods to produce water-repellent materials, which can offer protection against the effects of atmospheric water. Fluorosilanes are a very promising class of materials, as they act as precursors for the formation of low surface energy polymer networks. 1H,1H,2H,2H-perfluorooctyl-triethoxysilane is applied on marble, wood and the surfaces of other materials, such as glass, silicon wafer, brass, paper and silk. According to the measurements of static water contact angles, it is reported that superhydrophobicity and enhanced hydrophobicity are achieved on the surfaces of coated marble and wood, respectively. Hydrophobicity and hydrophilicity were observed on the treated surfaces of the other materials. More important, water repellency is achieved on any hydrophobic or superhydrophobic surface, as revealed by the very low sliding angles of water drops. The study is accompanied by colorimetric measurements to evaluate the effects of the treatment on the aesthetic appearances of the investigated materials. Finally, the capillary absorption test and a durability test are applied on treated wood and marble, respectively. 

scholarly journals Influence of organic manure amendments on water repellency, water entry value, and water retention of soil samples from a tropical Ultisol

2016 ◽  
Vol 64 (2) ◽  
pp. 160-166 ◽  
Author(s):  
T.D.P. Liyanage ◽  
D.A.L. Leelamanie
Keyword(s):  
Organic Matter ◽  
Soil Water ◽  
Water Retention ◽  
Water Repellency ◽  
Water Entry ◽  
Contact Angles ◽  
Organic Manure ◽  
Water Repellent ◽  
Water Contact ◽  
In Series

AbstractLowered stability of soil aggregates governed by insufficient organic matter levels has become a major concern in Sri Lanka. Although the use of organic manure with water repellent properties lowers the wetting rates and improves the stability of soil aggregates, its effects on soil hydrophysical properties are still not characterized. Therefore, the objective of this study was to examine the relation of water repellency induced by organic manure amendments to the water entry value and water retention of a Sri Lankan Ultisol. The soil was mixed with ground powders of cattle manure (CM), goat manure (GM),Gliricidia maculata(GL) and hydrophobicCasuarina equisetifolia(CE) leaves to obtain samples ranging from non-repellent to extremely water repellent, in two series. Series I was prepared by mixing GL and CE with soil (5, 10, 25, 50%). Series II consisted of 5% CM, GM, and GL, with (set A) and without (set B) intermixed 2% CE. Water repellency, water entry value, and water retention of samples were determined in the laboratory. Soil-water contact angle increased with increasing organic matter content in all the samples showing positive linear correlations. Although the samples amended with CE showed high soil-water contact angles in series I, set A (without 2% CE) and set B (with 2% CE) in series II did not show a noticeable difference, where >80% of the samples had soil-water contact angles <90°. Water entry value (R2= 0.83–0.92) and the water retention at 150 cm suction (R2= 0.69–0.8) of all the samples increased with increasing soil-water contact angles showing moderate to strong positive linear correlations. However, set A (without 2% CE) and set B (with 2% CE) in series II did not differ noticeably. Water entry value of about 60% the samples was <2.5 cm. Mixing of a small amount (2%) of hydrophobic organic matter with commonly used organic manures slightly increased the water repellency of sample soils, however not up to detrimental levels. It did not generate adverse effects on water entry and increased the water retention. It was clear that intermixing of small quantities of hydrophobic organic manure with organic manures commonly used in Sri Lankan agriculture, would not generate unfavorable impacts on soils.

scholarly journals 698 PB 306 WETTABILITY AND SURFACE TENSION OF FRUIT SURFACES

HortScience ◽  
1994 ◽  
Vol 29 (5) ◽  
pp. 533a-533 ◽  
Author(s):  
L. Cisneros-Zevallos ◽  
M. E. Saltveit ◽  
J. M Krochta
Keyword(s):  
Surface Tension ◽  
Water Repellency ◽  
High Water ◽  
Contact Angles ◽  
Stone Fruits ◽  
Water Contact ◽  
Wetting Behavior ◽  
Apple Cultivars ◽  
Chemical Groups ◽  
Apple Fruits

Nettability is an important factor to be considered in postharvest treatments such as washing, aqueous dippings, coatings, etc. Pome fruits (ten apple and four pear cultivars) and stone fruits (nectarine and plums) were evaluated for wetting behavior and surface tension at room temperature. Nettability was assessed by measuring contact angles of water. Surface tension was calculated by measuring contact angles of methylene iodide and water or by a series of pure surfactants using Zisman's method. Wetting behavior on apple fruits depended on cultivar, with water contact angles ranging from 75° to 131°. For pear fruits, wetting also depended on cultivar. Calculated surface tensions of pear fruits were in general higher than most apple cultivars tested. In stone fruits, plums presented a high water-repellency with a contact angle of 137°. The wetting of fruit surfaces seems to be governed by the nature of the chemical groups exposed on the surface of the cuticle and also by the surface roughness, as evidenced by tire high values of some contact angles.

scholarly journals Siloxane-Starch-Based Hydrophobic Coating for Multiple Recyclable Cellulosic Materials

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4977
Author(s):  
Tomasz Ganicz ◽  
Krystyna Rózga-Wijas
Keyword(s):  
High Surface ◽  
Barrier Properties ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Recycling Process ◽  
Water Contact ◽  
Cellulosic Materials ◽  
Circulating Water ◽  
Hydrophobic Coating ◽  
Aqueous Mixture

The results of the application of a new hydrophobization agent based on a triethoxymethylsilane and standard starch aqueous mixture for mass-produced cellulosic materials—printing paper, paperboard, and sack paper—have been evaluated to examine whether such a mixture can be used in industrial practice. The application of this agent on laboratory sheets prepared in a repetitive recycling process was performed to investigate its influence on the formation and properties of the products, as well as the contamination of circulating water. Measurements of the water contact angle, Cobb tests, and water penetration dynamics (PDA) were performed to test the barrier properties of the resulting materials. The effects of the applied coatings and recycling process on the paper’s tensile strength, tear index, roughness, air permeance, and ISO brightness were studied. Studies have proven that this formulation imparts relatively high surface hydrophobicity to all materials tested (contact angles above 100°) and a significant improvement in barrier properties while maintaining good mechanical and optical performance. The agent also does not interfere with the pulping and re-forming processes during recycling and increases circulation water contamination to an acceptable degree. Attenuated total reflectance Fourier-transform infrared (FT-IR) spectra of the paper samples revealed the presence of a polysiloxane network on the surface.

scholarly journals Super-Hydrophobic Co–Ni Coating with High Abrasion Resistance Prepared by Electrodeposition

Coatings ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 232 ◽  
Author(s):  
Yanpeng Xue ◽  
Shuqiang Wang ◽  
Peng Bi ◽  
Guochen Zhao ◽  
Ying Jin
Keyword(s):  
Carbon Steel ◽  
Steel Substrate ◽  
Low Cost ◽  
Applied Pressure ◽  
Cobalt Content ◽  
Contact Angles ◽  
Water Contact ◽  
Practical Utilization ◽  
Electrochemical Tests ◽  
Hydrophobic Coating

Although super-hydrophobic surfaces have great application prospects in industry, their preparation cost and mechanical durability have limited their practical utilization. In this work, we presented a new low-cost process preparation for super-hydrophobic Co–Ni coating on carbon steel substrate via an electrodeposition route. The deposited Co–Ni coating with cauliflower-shaped micro-nano structures exhibited high super-hydrophobic properties with water contact angles over 161° after modification with 1H,1H,2H,2H-Perfluorooctyltrichlorosilane (PFTEOS). Evaluated by the linear abrasion methods, the super-hydrophobic coating can maintain super-hydrophobicity after abrasion distance of 12 m under the applied pressure of 5 kPa, which was attributed to the high cobalt content of the Co–Ni coating. Moreover, electrochemical tests showed that the super-hydrophobic Co–Ni coatings exhibited a good anti-corrosion performance thus providing an adequate protection to the carbon steel substrates.

scholarly journals Durable and Superhydrophobic Aluminium Alloy with Microscale Hierarchical Structures and Anti-Drag Function Inspired by Diving Bell Spider

Coatings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1146
Author(s):  
You Chen ◽  
Zijing Quan ◽  
Yuhan Sun ◽  
Deqiang Chi ◽  
Delei Liu ◽  
...  
Keyword(s):  
Aluminium Alloy ◽  
Hierarchical Structures ◽  
Strong Acid ◽  
Contact Angles ◽  
Hierarchical Architecture ◽  
Viscous Drag ◽  
Microfluidic Chips ◽  
Coating Materials ◽  
Water Contact ◽  
Paint Systems

Coating materials with special surface wettability are widely applied in marine paint systems used in the naval industry to reduce the corrosion and viscous drag of seawater. However, traditional coatings are inefficient and limited, either by poor durability or insufficient anti-drag capacity. Here, inspired by the diving bell spider, a bionic superhydrophobic coating with multiscale hierarchical architecture was successfully prepared on the surface of aluminium alloy. It possesses excellent mechanical abrasion durability, chemical durability, and low adhesion. Remarkably, the water contact angles could remain over 150.9° after more than 15 abrasion cycles or strong acid/alkali conditions. In addition, the impacting water droplet lifted off the surface of bionic superhydrophobic aluminium alloy (BSAA) within 13 ms, illustrating an excellent low adhesion property. In fact, when the BSAA is immersed in water, it could absorb bubbles and form a gas membrane. The existence of the gas membrane could prevent water and anaerobic organisms from contacting and even corroding the BSAA. Meanwhile, the gas membrane acts as a lubricant and significantly deceases friction at the solid–liquid interface, reducing the drag for BSAA. The BSAA proposed in this work has broad application prospects, such as medical devices, microfluidic chips, gas separation and collection in water.

scholarly journals Effect of Sanding and Plasma Treatment of 3D-Printed Parts on Bonding to Wood with PVAc Adhesive

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1211
Author(s):  
Mirko Kariž ◽  
Daša Krapež Tomec ◽  
Sebastian Dahle ◽  
Manja Kitek Kuzman ◽  
Milan Šernek ◽  
...  
Keyword(s):  
Shear Strength ◽  
Plasma Treatment ◽  
Polylactic Acid ◽  
Wood Flour ◽  
Surface Preparation ◽  
Contact Angles ◽  
Fused Deposition Modelling ◽  
Water Contact ◽  
Fused Deposition ◽  
3D Printed

Additive manufacturing is becoming increasingly important for manufacturing end products, not just prototyping. However, the size of 3D-printed products is limited due to available printer sizes and other technological limitations. For example, making furniture from 3D-printed parts and wooden elements requires adequate adhesive joints. Since materials for 3D printing usually do not bond very well with adhesives designed for woodworking, they require special surface preparation to improve adhesion. In this study, fused deposition modelling (FDM) 3D-printed parts made of polylactic acid (PLA), polylactic acid with wood flour additive (Wood-PLA), and acrylonitrile-butadiene-styrene (ABS) polymers were bonded to wood with polyvinyl acetate (PVAc) adhesive. The surfaces of the samples were bonded as either non-treated, sanded, plasma treated, or sanded and plasma treated to evaluate the effect of each surface preparation on the bondability of the 3D-printed surfaces. Different surface preparations affected the bond shear strength in different ways. The plasma treatment significantly reduced water contact angles on all tested printing materials and increased the bond tensile shear strength of the adhesive used. The increase in bond strength was highest for the surfaces that had been both sanded and plasma treated. The highest increase was found for the ABS material (untreated 0.05 MPa; sanded and plasma treated 4.83 MPa) followed by Wood-PLA (from 0.45 MPa to 3.96 MPa) and PLA (from 0.55 MPa to 3.72 MPa). Analysis with a scanning electron microscope showed the smooth surfaces of the 3D-printed parts, which became rougher with sanding with more protruded particles, but plasma treatment partially melted the surface structures on the thermoplastic polymer surfaces.

Sign in / Sign up

Export Citation Format

Share Document