Improvement of Centrifugal Pump Performance by Using Different Impeller Diffuser Angles with and Without Vanes

2018 ◽  
Vol 35 (4) ◽  
pp. 577-589 ◽  
Author(s):  
D. Khoeini ◽  
E. Shirani ◽  
M. Joghataei
Keyword(s):  
Centrifugal Pump ◽  
Experimental Studies ◽  
High Flow ◽  
Divergence Angle ◽  
Centrifugal Pumps ◽  
Pump Impeller ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Operating Region ◽  
Overall Efficiency

ABSTRACTThis study aims at improving the performance of a centrifugal pump by using different angular diffusers on the downstream side of the centrifugal pump impeller. Numerical and experimental studies have been carried out on different vaned and non-vaned diffuser with three different wall divergence angle (α) of 0°, 5° and 10° to achieve that purpose. The data analyses show good agreement between the numerical and experimental results. They reveal profound effect of the divergence angle (α) of angular vaned diffuser on the head and overall efficiency of centrifugal pumps especially at high flow rates as they broaden operating region of the centrifugal pump. In fact it is found that the head and overall efficiency of impeller with vaned diffuser α = 10° enhance by 15.4 and 9 percent respectively compared to that of centrifugal pump with no vaned diffuser at high flow rates. Furthermore the head and overall efficiency of impeller with vaned diffuser α = 10° increase by 5.7 and 7 percent respectively in comparison with the impeller with vaned diffuser α = 0°.

Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump

2019 ◽  
Vol 36 (4) ◽  
pp. 401-410 ◽  
Author(s):  
Xiao-Qi Jia ◽  
Bao-Ling Cui ◽  
Zu-Chao Zhu ◽  
Yu-Liang Zhang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
High Flow ◽  
Low Flow ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Pressure Distributions ◽  
Blade Passing Frequency

Abstract Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.

Comparison of Inlet Curved Disk Arrangements for Suppression of Recirculation in Centrifugal Pump Impellers

2016 ◽  
Author(s):  
Munther Y. Hermez ◽  
Badih A. Jawad ◽  
Liping Liu ◽  
Vernon Fernandez ◽  
Kingman Yee ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Operating Cost ◽  
Three Dimensional ◽  
Centrifugal Pumps ◽  
Unstable Flow ◽  
Pump Impeller ◽  
Flow Rates ◽  
Flow Recirculation ◽  
Flow Field Characteristics

The present work aims to numerically study the inlet flow recirculation and modified impeller interaction in a centrifugal pump. An optimization of modified shrouded impeller with curved disk arrangement to suppress the unsteady flow recirculation is pursued. This modification will enhance the impeller characteristics with a wider operation range at both low and high flow rates in a high speed centrifugal pump type. The unstable flow in the centrifugal pumps is a common problem that leads to damage in the pump’s internal parts, consequently increases the operating cost. At certain flow rates, generally below the Best Efficiency Point (BEP), all centrifugal pumps are subject to internal recirculation occurs at the suction and discharge areas of the impeller. For decades, experimental work has been done to investigate the complex three-dimensional flow within centrifugal pumps impellers, before computational work gains momentum due to advancement of computing power and improved numerical codes. In this study the impeller with a curved disk arrangement has been investigated by using a three-dimensional Navier-Stokes code with a standard k-ε turbulence model. The purpose is to evaluate and select the optimum impeller modification that would increase the pump suction flow rate range. Three-dimensional numerical Computational Fluid Dynamics (CFD) tools are used to simulate flow field characteristics inside the centrifugal pump and provide critical hydraulic design information. In the present work, ANSYS v.16.1 Fluent solver is used to analyze the pressure and velocity distributions inside impeller suction and discharge passages. The ultimate goal of this study is to manufacture and validate the most optimized and efficient centrifugal pump impeller with a curved disk. The best case curve identifies the highest increase of total pressure difference by 22.1%, and highest efficiency by 92.3% at low flowrates.

scholarly journals Investigation on centrifugal pump performance degradation under air-water inlet two-phase flow conditions

2018 ◽  
pp. 41-48 ◽  
Author(s):  
Qiaorui Si ◽  
Qianglei Cui ◽  
Keyu Zhang ◽  
Jianping Yuan ◽  
Gérard Bois
Keyword(s):  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Flow Characteristics ◽  
Performance Degradation ◽  
Inlet Pressure ◽  
Pulsation Frequency ◽  
Centrifugal Pumps ◽  
Two Phase ◽  
Flow Rates ◽  
Pump Performance

In order to study the flow characteristics of centrifugal pumps when transporting the gas-liquid mixture, water and air were chosen as the working medium. Both numerical simulation and experimental tests were conducted on a centrifugal pump under different conditions of inlet air volume fraction (IAVF). The calculation used URANS k-epsilon turbulence model combined with the Euler-Euler inhomogeneous two-phase model. The air distribution and velocity streamline inside the impeller were obtained to discuss the flow characteristics of the pump. The results show that air concentration is high at the inlet pressure side of the blade, where the vortex will exist, indicating that the gas concentration have a great relationship with the vortex aggregation in the impeller passages. In the experimental works, pump performances were measured at different IAVF and compared with numerical results. Contributions to the centrifugal pump performance degradations were analyzed under different air-water inlet flow condition such as IAVF, bubble size, inlet pressure. Results show that pump performance degradation is more pronounced for low flow rates compared to high flow rates. Finally, pressure pulsation and vibration experiments of the pump model under different IAVF were also conducted. Inlet and outlet transient pressure signals under four IAVF were investigated and pressure pulsation frequency of the monitors is near the blade passing frequency at different IAVF, and when IAVF increased, the lower frequency signal is more and more obvious. Vibration signals at five measuring points were also obtained under different IAVF for various flow rates.

Optimal Design and Experimental Study on 500SM35 Type Centrifugal Pump

2010 ◽  
Vol 29-32 ◽  
pp. 1003-1007
Author(s):  
Ming Wei Hou
Keyword(s):  
Centrifugal Pump ◽  
Optimization Design ◽  
High Efficiency ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Multi Objective Optimization ◽  
Centrifugal Pumps ◽  
Design Specification ◽  
Turbulence Flow ◽  
Hydraulic Design

To make the high efficiency and energy-saving centrifugal pump, using multi-objective optimization design to make hydraulic design of the 500SM35 centrifugal pumps, using CFD technology to simulate the three-dimensional turbulence flow in pump, also make performance experiment and cavitation experiment of the 500SM35 centrifugal pump that have been self-developed. Experimental studies have shown that: the 500SM35 centrifugal pump’s prototype performance parameters all beyond design specification.

scholarly journals Optimization and Analysis of Centrifugal Pump considering Fluid-Structure Interaction

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Yu Zhang ◽  
Sanbao Hu ◽  
Yunqing Zhang ◽  
Liping Chen
Keyword(s):  
Centrifugal Pump ◽  
Fluid Structure Interaction ◽  
Kriging Model ◽  
Geometrical Parameters ◽  
Centrifugal Pumps ◽  
Transient Vibration ◽  
Pump Impeller ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Vibration Performance

This paper presents the optimization of vibrations of centrifugal pump considering fluid-structure interaction (FSI). A set of centrifugal pumps with various blade shapes were studied using FSI method, in order to investigate the transient vibration performance. The Kriging model, based on the results of the FSI simulations, was established to approximate the relationship between the geometrical parameters of pump impeller and the root mean square (RMS) values of the displacement response at the pump bearing block. Hence, multi-island genetic algorithm (MIGA) has been implemented to minimize the RMS value of the impeller displacement. A prototype of centrifugal pump has been manufactured and an experimental validation of the optimization results has been carried out. The comparison among results of Kriging surrogate model, FSI simulation, and experimental test showed a good consistency of the three approaches. Finally, the transient mechanical behavior of pump impeller has been investigated using FSI method based on the optimized geometry parameters of pump impeller.

The effect of wear ring clearance on flow field in the impeller sidewall gap and efficiency of a low specific speed centrifugal pump

2017 ◽  
Vol 232 (17) ◽  
pp. 3062-3073 ◽  
Author(s):  
M DaqiqShirazi ◽  
R Torabi ◽  
A Riasi ◽  
SA Nourbakhsh
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Volumetric Efficiency ◽  
Centrifugal Pumps ◽  
Disk Friction ◽  
Low Specific Speed ◽  
Overall Efficiency ◽  
Specific Speed

In this paper, the flow in the impeller sidewall gap of a low specific speed centrifugal pump is analyzed to study the effect of wear ring clearance and the resultant through-flow on flow field in this cavity and investigate the overall efficiency of the pump. Centrifugal pumps are commonly subject to a reduction in the flow rate and volumetric efficiency due to abrasive liquids or working conditions, since the wear rings are progressively worn, the internal leakage flow is increased. In the new operating point, the overall efficiency of the pump cannot be predicted simply by using the pump characteristic curves. The flow field is simulated with the use of computational fluid dynamics and the three-dimensional full Navier–Stokes equations are solved using CFX software. In order to verify the numerical simulations, static pressure field in volute casing and pump performance curves are compared with the experimental measurements. The results show that, for the pump with minimum wear ring clearance, the disk friction efficiency is the strongest factor that impairs the overall efficiency. Therefore, when the ring clearance is enlarged more than three times, although volumetric efficiency decreases effectively but the reduction in overall efficiency is remarkably smaller due to improvement in the disk friction losses.

Numerical Simulation of Hysteresis on Head/Discharge Characteristics of a Centrifugal Pump

2003 ◽  
Author(s):  
Masamichi Iino ◽  
Kazuhiro Tanaka ◽  
Kazuyoshi Miyagawa ◽  
Takeshi Okubo
Keyword(s):  
Numerical Simulation ◽  
Hysteresis Loop ◽  
Centrifugal Pump ◽  
Characteristic Curve ◽  
Swirl Flow ◽  
Centrifugal Pumps ◽  
Pump Impeller ◽  
Discharge Characteristics ◽  
Discharge Characteristic ◽  
Partial Load

The objectives of the present study were to investigate influences of fins, set in a suction part, on the positive slope and hysteresis loop in head/discharge characteristic curves of centrifugal pumps in the experiment as well as in the numerical prediction. The fins were located in upstream side of a pump impeller to suppress swirl flow occurring before the impeller inlet at partial load operation. We had two kinds of centrifugal pump with/without the fins, the number of which is 16. These two centrifugal pumps had a shrouded impeller with 7 blades and a diffuser with 20 guide vanes with the same configuration. In the experiment, the pump with them had a large hysteresis loop at partial load operation in the head/discharge characteristic curve, although the pump without them had no hysteresis loop. In the numerical simulation based on periodic flow, the incompressible turbulent flow field was calculated for partial blade-passages with periodic boundary conditions. As a result, the simulated characteristics had the same tendencies as the experimental results. Furthermore, the causes of the discontinuous head/discharge characteristics depending on the direction of partial load operation were clarified through calculating and comparing the internal flow fields in the cases with/without the fins. The pumps had the large backflow and recirculation areas in two places, one of which was near the shroud at the impeller inlet including the fins area and another near the central part of the diffuser. The difference in the hysteresis loop between with and without the fins was caused by the existence of the fins, which suppressed or promoted the backflow at the impeller.

scholarly journals CFD simulation on centrifugal pump impeller with splitter blades

2020 ◽  
Vol 24 (1) ◽  
pp. 3-7 ◽  
Author(s):  
Henrique M. P. Rosa ◽  
Bruno S. Emerick
Keyword(s):  
Centrifugal Pump ◽  
Cfd Simulation ◽  
Computational Simulations ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Flow Rates ◽  
Computational Fluids Dynamics ◽  
Ansys Cfx ◽  
Computational Fluids ◽  
Centrifugal Pump Impeller

ABSTRACT The present paper aims to present the analysis and comparison of results of computational simulations using Computational Fluids Dynamics (CFD) in impellers of centrifugal pump. Three impellers were simulated: 1) original impeller, 2) original impeller with splitter blades at outlet; 3) original impeller with splitter blades at inlet. The splitters occupied 30% of the length of the main blades. They were simulated using the ANSYS-CFX software system in 1500 rpm rotational speed and at different flow rates. The turbulence model assumed was the Shear Stress Transport (SST). The results were used to build impeller blade head curves, besides the presentation of pressure distribution and streamline behaviour inside the impeller. It was verified that the insertion of the splitter blades reduced the impeller blade head, mainly the impeller with outlet splitter, whose reduction was more intense.

Effect of vaned diffuser clocking position on hydraulic performance and pressure pulsation of centrifugal pump

2020 ◽  
pp. 095765092096724
Author(s):  
Hongyu Guan ◽  
Wei Jiang ◽  
Yuchuan Wang ◽  
Gaoyang Hou ◽  
Xiangyuan Zhu ◽  
...  
Keyword(s):  
Energy Loss ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Guide Vane ◽  
Hydraulic Performance ◽  
Design Flow ◽  
Maximum Difference ◽  
Centrifugal Pumps ◽  
Vaned Diffuser ◽  
Diffuser Flow

The clocking position of the vaned diffuser, the circumferential position of the vaned diffuser relative to the volute, has a certain effect on the performance of the centrifugal pump. Therefore, this paper studies the guide vane centrifugal pump from the aspects of pressure pulsation, hydraulic performance, and energy loss. The maximum difference in efficiency is 3.4% under the design flow rate, and the maximum difference in the head coefficient is 4.7%. The hydraulic performance and pressure pulsation present different trends with the increase of the vaned diffuser clock angle. When the hydraulic performance and pressure pulsation are relatively good, the circumferential distance between the tongue and the upstream vaned diffuser blade is 3/4 of the diffuser flow path. In addition, the recommended vaned diffuser installation location may also be suitable for centrifugal pumps of similar construction. The energy loss was visualized using the theory of entropy production. The distributions of energy loss and flow field indicate that the energy loss of impeller and vaned diffuser changes little. The change of the vortex in the tongue and outlet area will cause a significant change in the energy loss of the volute, which is the main reason that the hydraulic performance of the centrifugal pump is affected by the clocking position of the vaned diffuser.

Design and Analysis of Airfoil-Shaped Impeller Blades of Centrifugal Pump

2016 ◽  
Vol 852 ◽  
pp. 539-544
Author(s):  
Parth Shah ◽  
M. Ashwin Ganesh ◽  
Thundil Kuruppa Raj
Keyword(s):  
Centrifugal Pump ◽  
Transport Model ◽  
Turbulence Models ◽  
Suction Side ◽  
3D Analysis ◽  
Centrifugal Pumps ◽  
Pump Impeller ◽  
Outlet Pressure ◽  
Shear Stress Transport Model ◽  
Centrifugal Pump Impeller

This paper deals with a comparative study of the outlet pressure-energy between a conventional and normal blade impeller and an airfoil-shaped blade impeller of a centrifugal pump. Although the volute casing is an important component along with an impeller [1], the present comparative analysis makes the volute casing redundant to the study, hence neglected. All centrifugal pumps are usually designed and manufactured using backward swept blades with equal camber on the top and bottom sides. An increased camber on the top side is an ideal trait for a lift generating airfoil. The purpose is to implement the principle of lift generation of airfoil for centrifugal pumps. As a result, a local suction side and pressure side can be visualized using CFX-post processor. The 3D analysis of such a centrifugal pump impeller is designed in SOLIDWORKS® and analyzed using ANSYS® CFX. The SST (Menter’s Shear Stress Transport) model is used as it combines both the k-ω and k-ε turbulence models.

Sign in / Sign up

Export Citation Format

Share Document