Receptivity of inviscid modes in supersonic boundary layers due to scattering of free-stream sound by localised wall roughness

2020 ◽  
Vol 896 ◽  
Author(s):  
Ming Dong ◽  
Yinhui Liu ◽  
Xuesong Wu
Keyword(s):  
Boundary Layers ◽  
Free Stream ◽  
Wall Roughness ◽  
Image Position

Effects of Embedded Vortices on Film-Cooled Turbulent Boundary Layers

1989 ◽  
Vol 111 (1) ◽  
pp. 71-77 ◽  
Author(s):  
P. M. Ligrani ◽  
A. Ortiz ◽  
S. L. Joseph ◽  
D. L. Evans
Keyword(s):  
Heat Transfer ◽  
Boundary Layers ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Behavior ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Turbulent Boundary Layers ◽  
Stream Velocity ◽  
Longitudinal Vortices

Heat transfer effects of longitudinal vortices embedded within film-cooled turbulent boundary layers on a flat plate were examined for free-stream velocities of 10 m/s and 15 m/s. A single row of film-cooling holes was employed with blowing ratios ranging from 0.47 to 0.98. Moderate-strength vortices were used with circulating-to-free stream velocity ratios of −0.95 to −1.10 cm. Spatially resolved heat transfer measurements from a constant heat flux surface show that film coolant is greatly disturbed and that local Stanton numbers are altered significantly by embedded longitudinal vortices. Near the downwash side of the vortex, heat transfer is augmented, vortex effects dominate flow behavior, and the protection from film cooling is minimized. Near the upwash side of the vortex, coolant is pushed to the side of the vortex, locally increasing the protection provided by film cooling. In addition, local heat transfer distributions change significantly as the spanwise location of the vortex is changed relative to film-cooling hole locations.

On the transient response of the turbulent boundary layer inception in compressible flows

2018 ◽  
Vol 850 ◽  
pp. 1117-1141 ◽  
Author(s):  
J. Saavedra ◽  
G. Paniagua ◽  
S. Lavagnoli
Keyword(s):  
Boundary Layer ◽  
Flow Control ◽  
Boundary Layers ◽  
Thermal Boundary Layer ◽  
Free Stream ◽  
Test Model ◽  
Additional Time ◽  
Time Required ◽  
Momentum Boundary Layer

The behavioural characteristics of thermal boundary layer inception dictate the efficiency of heat exchangers and the operational limits of fluid machinery. The specific time required by the thermal boundary layer to be established is vital to optimize flow control strategies, as well as the thermal management of systems exposed to ephemeral phenomena, typically on the millisecond scale. This paper presents the time characterization of the momentum and thermal boundary layer development in transient turbulent compressible air flows. We present a new framework to perform such estimations based on detailed unsteady Reynolds averaged Navier–Stokes simulations that may be extended to higher fidelity simulations. First of all, the aerodynamic boundary layer initiation is described using adiabatic simulations. Additional numerical calculations were then performed by setting the isothermal wall condition to evaluate the additional time required by the thermal boundary layer to establish after the aerodynamic boundary layer reaches its steady state. Finally, full conjugate simulations were executed to compute the warm up effect of the solid during the blowdown of a hot fluid over a colder metallic test model. The transient performance of the turbulent thermal and momentum boundary layers is quantified through numerical simulations of air blowdown over a flat plate for different mainstream flow conditions. The effects of Reynolds number, free stream velocity, transient duration, test article length and free stream temperature were independently assessed, to then define a mathematical expression of the momentum boundary layer settlement. This paper presents a novel numerical correlation of the additional time required by the thermal boundary layer to be stablished after the settlement of the momentum boundary layer. The time scales of the aerodynamic and thermal boundary layers are presented as a function of relevant non-dimensional numbers, as well as the description of the response of the near wall flow to sudden free stream changes. The characterization of the boundary layer mechanisms discussed in this paper contribute to the establishment of an evidence-based foundation for advances in the field of flow control.

Prediction of Turbulent Boundary Layers With a Second-Moment Closure: Part I—Effects of Periodic Pressure Gradient, Wall Transpiration, and Free-Stream Turbulence

1993 ◽  
Vol 115 (1) ◽  
pp. 56-63 ◽  
Author(s):  
N. Shima
Keyword(s):  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Moment Closure ◽  
Second Moment ◽  
Free Stream Turbulence ◽  
Periodic Pressure ◽  
Second Moment Closure ◽  
Oscillating Boundary ◽  
Present Part

The purpose of this two-part paper is to assess the performance of a second-moment closure applicable up to a wall. In the present part, the turbulence model is applied to the boundary layers with periodic pressure gradient, with wall transpiration and with free-stream turbulence. The predictions are shown to be in good agreement with experiments and a direct simulation. In particular, a tendency towards relaminarization and a subsequent retransition in the oscillating boundary layer are faithfully reproduced, and the effect of the length scale of free-stream turbulence is correctly captured.

Boundary layer development after a separated region

1998 ◽  
Vol 374 ◽  
pp. 91-116 ◽  
Author(s):  
IAN P. CASTRO ◽  
ELEANORA EPIK
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulence Models ◽  
Separated Flow ◽  
Leading Edge ◽  
Turbulence Structure ◽  
Outer Flow ◽  
Free Stream Turbulence ◽  
Layer Region

Measurements obtained in boundary layers developing downstream of the highly turbulent, separated flow generated at the leading edge of a blunt flat plate are presented. Two cases are considered: first, when there is only very low (wind tunnel) turbulence present in the free-stream flow and, second, when roughly isotropic, homogeneous turbulence is introduced. With conditions adjusted to ensure that the separated region was of the same length in both cases, the flow around reattachment was significantly different and subsequent differences in the development rate of the two boundary layers are identified. The paper complements, but is much more extensive than, the earlier presentation of some of the basic data (Castro & Epik 1996), confirming not only that the development process is very slow, but also that it is non-monotonic. Turbulence stress levels fall below those typical of zero-pressure-gradient boundary layers and, in many ways, the boundary layer has features similar to those found in standard boundary layers perturbed by free-stream turbulence. It is argued that, at least as far as the turbulence structure is concerned, the inner layer region develops no more quickly than does the outer flow and it is the latter which essentially determines the overall rate of development of the whole flow. Some numerical computations are used to assess the extent to which current turbulence models are adequate for such flows.

Sign in / Sign up

Export Citation Format

Share Document