Three-dimensional organization and dynamics of vortices in multichannel swirling jets

2018 ◽  
Vol 843 ◽  
pp. 180-210 ◽  
Author(s):  
Andrea Ianiro ◽  
Kyle P. Lynch ◽  
Daniele Violato ◽  
Gennaro Cardone ◽  
Fulvio Scarano
Keyword(s):  
Flow Field ◽  
Shear Layer ◽  
Vortex Core ◽  
Vortex Breakdown ◽  
Three Dimensional ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Flow Topology ◽  
Swirl Number ◽  
Initial Development

The unsteady three-dimensional flow organization of jets issued from a duct with swirl vanes at Reynolds number equal to 1000 and swirl number $S$ ranging between 0 and 0.8 is investigated. Time-resolved tomographic particle image velocimetry returns the instantaneous flow structure and its evolution by visualization of velocity and vortical features. The most relevant coherent motions are identified and characterized with the aid of dynamic mode decomposition. The time-averaged flow topology indicates that the vanes used to impart the swirling motion have a significant impact on the azimuthal modulation of momentum, with the jet exhibiting four sectors separated by a thin cross-like wake resulting from the boundary layer developed along the vane walls. The flow field is thus characterized by inner and outer shear regions. An increase in swirl, up to moderate levels ($S=0.4$), causes larger jet spreading angles. Further increase of the swirl number is accompanied by the appearance of a central recirculation zone due to vortex breakdown at $S=0.6$ which increases in size and is triggered upstream for increasing $S$. Although no shear layer instability development is observed at $S=0$, already at $S=0.2$ the swirling motion promotes the growth of helical vortices appearing as Kelvin–Helmholtz waves that deform the outer axial shear layer. The downstream evolution features successive pairing, which is observed for all the considered swirl numbers. The initial development of the instability is independent for each vane, whereas a mutual interaction between the vanes occurs after the vortex pairing. The reconnection from the four sectors vortices induces a significant increase of azimuthal vorticity, which affects the dynamical behaviour of the precessing vortex core. The latter is visualized by a low-order spatio-temporal reconstruction based on few dynamical modes. At a higher swirl number ($S\geqslant 0.6$), the axial vorticity component dominates the flow field; it interacts with the azimuthal vorticity, which penetrates inward through the meanders of the vane wakes and forces the vortex core precession and breakdown.

A numerical study of shear layer characteristics of low-speed transverse jets

2016 ◽  
Vol 790 ◽  
pp. 275-307 ◽  
Author(s):  
Prahladh S. Iyer ◽  
Krishnan Mahesh
Keyword(s):  
Velocity Profile ◽  
Shear Layer ◽  
Convective Instability ◽  
Numerical Study ◽  
Velocity Ratio ◽  
Mixing Layer ◽  
Three Dimensional ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Dominant Frequencies

Direct numerical simulation (DNS) and dynamic mode decomposition (DMD) are used to study the shear layer characteristics of a jet in a crossflow. Experimental observations by Megerian et al. (J. Fluid Mech., vol. 593, 2007, pp. 93–129) at velocity ratios ($R=\overline{v}_{j}/u_{\infty }$) of 2 and 4 and Reynolds number ($Re=\overline{v}_{j}D/{\it\nu}$) of 2000 on the transition from absolute to convective instability of the upstream shear layer are reproduced. Point velocity spectra at different points along the shear layer show excellent agreement with experiments. The same frequency ($St=0.65$) is dominant along the length of the shear layer for $R=2$, whereas the dominant frequencies change along the shear layer for $R=4$. DMD of the full three-dimensional flow field is able to reproduce the dominant frequencies observed from DNS and shows that the shear layer modes are dominant for both the conditions simulated. The spatial modes obtained from DMD are used to study the nature of the shear layer instability. It is found that a counter-current mixing layer is obtained in the upstream shear layer. The corresponding mixing velocity ratio is obtained, and seen to delineate the two regimes of absolute or convective instability. The effect of the nozzle is evaluated by performing simulations without the nozzle while requiring the jet to have the same inlet velocity profile as that obtained at the nozzle exit in the simulations including the nozzle. The shear layer spectra show good agreement with the simulations including the nozzle. The effect of shear layer thickness is studied at a velocity ratio of 2 based on peak and mean jet velocity. The dominant frequencies and spatial shear layer modes from DNS/DMD are significantly altered by the jet exit velocity profile.

Temporal and spatial evolution of cavitating bubbles and coherent structures in a confined submerged jet shear layer

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Runqiang Zhang ◽  
Guoyong Sun ◽  
Yuchuan Wang ◽  
Sebastián Leguizamón
Keyword(s):  
Shear Layer ◽  
Coherent Structures ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Content Type ◽  
Cavitation Inception ◽  
Mode Decomposition ◽  
The Relationship

PurposeThe study aims to display the bubbles' evolution in the shear layer and their relationship with the pressure fluctuations. Furthermore, the coherent structures of the first six modes are extracted, in order to provide insight into their temporal and spatial evolution and determine the relationship between cavitating bubbles and coherent structures.Design/methodology/approachIn the present study, numerical simulations of submerged jet cavitating flow were carried out at a cavitation inception condition inside an axisymmetric cavity using the large eddy simulation (LES) turbulence model and the Schnerr–Sauer (S–S) cavitation model. Based on snapshots produced by the numerical simulation, dynamic mode decomposition (DMD) was performed to extract the three-dimensional coherent structures of the first six modes in the shear layer.FindingsThe cavitating bubbles in the shear layer are deformed to elongated ellipsoid shapes by shear forces. The significant pressure fluctuations are induced by the collapse of the biggest bubble in the group. The first mode illustrates the mean characteristics of the flow field. The flow in the peripheral region of the shear layer is mainly dominated by large-scale coherent structures revealed by the second and third modes, while different small-scale coherent structures are contained in the central region. The cavitating bubbles are associated with small size coherent structures as the sixth or higher modes.Practical implicationsThis work demonstrates the feasibility of LES for high Reynolds number shear layer flow. The dynamic mode decomposition method is a novel method to extract coherent structures and obtain their dynamic information that will help us to optimize and control the flow.Originality/value(1) This paper first displays the three-dimensional coherent structures and their characteristics in the shear layer of confined jet flow. (2) The relationship of bubbles shape and pressure fluctuations is illustrated. (3) The visualization of coherent structures benefits the understanding of the mixing process and cavitation inception in jet shear layers.

scholarly journals Analysis of transonic buffet using dynamic mode decomposition

2021 ◽  
Vol 62 (4) ◽  
Author(s):  
Antje Feldhusen-Hoffmann ◽  
Christian Lagemann ◽  
Simon Loosen ◽  
Pascal Meysonnat ◽  
Michael Klaas ◽  
...  
Keyword(s):  
Shock Wave ◽  
Flow Field ◽  
Acoustic Waves ◽  
Feedback Loop ◽  
Measurement Data ◽  
Dynamic Mode Decomposition ◽  
Recirculation Region ◽  
Dynamic Mode ◽  
Mode Decomposition ◽  
Transonic Buffet

AbstractThe buffet flow field around supercritical airfoils is dominated by self-sustained shock wave oscillations on the suction side of the wing. Theories assume that this unsteadiness is driven by a feedback loop of disturbances in the flow field downstream of the shock wave whose upstream propagating part is generated by acoustic waves. High-speed particle-image velocimetry measurements are performed to investigate this feedback loop in transonic buffet flow over a supercritical DRA 2303 airfoil. The freestream Mach number is $$M_{\infty } = 0.73$$ M ∞ = 0.73 , the angle of attack is $$\alpha = 3.5^{\circ }$$ α = 3 . 5 ∘ , and the chord-based Reynolds number is $${\mathrm{Re}}_{c} = 1.9\times 10^6$$ Re c = 1.9 × 10 6 . The obtained velocity fields are processed by sparsity-promoting dynamic mode decomposition to identify the dominant dynamic features contributing strongest to the buffet flow field. Two pronounced dynamic modes are found which confirm the presence of two main features of the proposed feedback loop. One mode is related to the shock wave oscillation frequency and its shape includes the movement of the shock wave and the coupled pulsation of the recirculation region downstream of the shock wave. The other pronounced mode represents the disturbances which form the downstream propagating part of the proposed feedback loop. The frequency of this mode corresponds to the frequency of the acoustic waves which are generated by these downstream traveling disturbances and which form the upstream propagating part of the proposed feedback loop. In this study, the post-processing, i.e., the DMD, is highlighted to substantiate the existence of this vortex mode. It is this vortex mode that via the Lamb vector excites the shock oscillations. The measurement data based DMD results confirm numerical findings, i.e., the dominant buffet and vortex modes are in good agreement with the feedback loop suggested by Lee. Graphic abstract

scholarly journals Analysis of V-Gutter Reacting Flow Dynamics Using Proper Orthogonal and Dynamic Mode Decompositions

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4886 ◽  
Author(s):  
Yang Yang ◽  
Xiao Liu ◽  
Zhihao Zhang
Keyword(s):  
Shear Layer ◽  
Large Scale ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Reacting Flow ◽  
Eddy Simulation ◽  
Mode Decomposition ◽  
Wake Instability ◽  
Shedding Frequency ◽  
Proper Orthogonal

The current work is focused on investigating the potential of data-driven post-processing techniques, including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) for flame dynamics. Large-eddy simulation (LES) of a V-gutter premixed flame was performed with two Reynolds numbers. The flame transfer function (FTF) was calculated. The POD and DMD were used for the analysis of the flame structures, wake shedding frequency, etc. The results acquired by different methods were also compared. The FTF results indicate that the flames have proportional, inertial, and delay components. The POD method could capture the shedding wake motion and shear layer motion. The excited DMD modes corresponded to the shear layer flames’ swing and convect motions in certain directions. Both POD and DMD could help to identify the wake shedding frequency. However, this large-scale flame oscillation is not presented in the FTF results. The negative growth rates of the decomposed mode confirm that the shear layer stabilized flame was more stable than the flame possessing a wake instability. The corresponding combustor design could be guided by the above results.

Unravelling the large-scale circulation modes in turbulent Rayleigh–Bénard convection

2021 ◽  
Author(s):  
Susanne Horn ◽  
Peter J. Schmid ◽  
Jonathan M. Aurnou
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Mean Flow ◽  
Large Scale Circulation ◽  
Convective Systems ◽  
Aspect Ratios ◽  
Mode Decomposition ◽  
Coherent Flow Structure

Abstract The large-scale circulation (LSC) is the most fundamental turbulent coherent flow structure in Rayleigh-B\'enard convection. Further, LSCs provide the foundation upon which superstructures, the largest observable features in convective systems, are formed. In confined cylindrical geometries with diameter-to-height aspect ratios of Γ ≅ 1, LSC dynamics are known to be governed by a quasi-two-dimensional, coupled horizontal sloshing and torsional (ST) oscillatory mode. In contrast, in Γ ≥ √2 cylinders, a three-dimensional jump rope vortex (JRV) motion dominates the LSC dynamics. Here, we use dynamic mode decomposition (DMD) on direct numerical simulation data of liquid metal to show that both types of modes co-exist in Γ = 1 and Γ = 2 cylinders but with opposite dynamical importance. Furthermore, with this analysis, we demonstrate that ST oscillations originate from a tilted elliptical mean flow superposed with a symmetric higher order mode, which is connected to the four rolls in the plane perpendicular to the LSC in Γ = 1 tanks.

Analysis of dynamic stall flow field of high bypass fan rotor based on airworthiness certification

2020 ◽  
Vol 234 (11) ◽  
pp. 1757-1769
Author(s):  
Kai Zhang ◽  
AJ Wang
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Field Data ◽  
Decomposition Methods ◽  
Modal Identification ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Complex Flow ◽  
Mode Decomposition ◽  
Proper Orthogonal

In order to ensure flight safety, the stall test is one of the most important steps in the airworthiness certification phase of civil aircraft. The twisted-swept fan is one of the most important components of the high bypass ratio engine. The unsteady flow field of the fan rotor stall condition is obtained by numerical simulation. At the same time, the time series flow field data of the stall condition flow field is acquired. The modal analysis of the unsteady flow field at stall condition was performed using the dynamic mode decomposition and proper orthogonal decomposition methods. Through modal identification of a large number of unsteady flow field data, the eigenvalues and corresponding modal information about the unsteady flow field change process are obtained. Finally, the evolution process of the unsteady flow field of the fan rotor under stall condition is visually demonstrated, and the coherent structures of different scales in the complex flow field under stall condition are revealed.

scholarly journals Simultaneous Measurement of Free Surface Elevation and Three-Component Velocity Field Around a Translating Surface-Piercing Foil

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
James Schock ◽  
Jason Dahl
Keyword(s):  
Particle Image Velocimetry ◽  
Free Surface ◽  
Velocity Field ◽  
Numerical Methods ◽  
Flow Field ◽  
Particle Image ◽  
Laser Sheet ◽  
Three Dimensional ◽  
Dynamic Mode ◽  
Image Velocimetry

Two methods are investigated to simultaneously obtain both three-dimensional (3D) velocity field and free surface elevations (FSEs) measurements near a surface piercing foil, while limiting the equipment. The combined velocity field and FSE measurements are obtained specifically for the validation of numerical methods requiring simultaneous field data and free surface measurements for a slender body shape. Both methods use stereo particle image velocimetry (SPIV) to measure three component velocities in the flow field and both methods use an off the shelf digital camera with a laser intersection line to measure FSEs. The first method is performed using a vertical laser sheet oriented parallel to the foil chord line. Through repetition of experiments with repositioning of the laser, a statistical representation of the three-dimensional flow field and surface elevations is obtained. The second method orients the vertical laser sheet such that the foil chord line is orthogonal to the laser sheet. A single experiment is performed with this method to measure the three-dimensional three component (3D3C) flow field and free surface, assuming steady flow conditions, such that the time dimension is used to expand the flow field in 3D space. The two methods are compared using dynamic mode decomposition and found to be comparable in the primary mode. Utilizing these methods produces results that are acceptable for use in numerical methods verification, at a fraction of the capital and computing cost associated with two plane or tomographic particle image velocimetry (PIV).

Three-dimensional flow within shallow, narrow cavities

2013 ◽  
Vol 735 ◽  
pp. 587-612 ◽  
Author(s):  
Sarah D. Crook ◽  
Timothy C. W. Lau ◽  
Richard M. Kelso
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Particle Image Velocimetry Data ◽  
Cavity Flow ◽  
Dimensional Structure ◽  
Back Surface ◽  
Flow Topology ◽  
Open Type ◽  
Flow Features ◽  
Cavity Opening

AbstractThe three-dimensional structure of incompressible flow in a narrow, open rectangular cavity in a flat plate was investigated with a focus on the flow topology of the time-averaged flow. The ratio of cavity length (in the direction of the flow) to width to depth was $l{: }w{: }d= 6{: }2{: }1$. Experimental surface pressure data (in air) and particle image velocimetry data (in water) were obtained at low speed with free-stream Reynolds numbers of ${\mathit{Re}}_{l} = 3. 4\times 1{0}^{5} $ in air and ${\mathit{Re}}_{l} = 4. 3\times 1{0}^{4} $ in water. The experimental results show that the three-dimensional cavity flow is of the ‘open’ type, with an overall flow structure that bears some similarity to the structure observed in nominally two-dimensional cavities, but with a high degree of three-dimensionality both in the flow near the walls and in the unsteady behaviour. The defining features of an open-type cavity flow include a shear layer that traverses the entire cavity opening ultimately impinging on the back surface of the cavity, and a large recirculation zone within the cavity itself. Other flow features that have been identified in the current study include two vortices at the back of the cavity, of which one is barely visible, a weak vortex at the front of the cavity, and a pair of counter-rotating streamwise vortices along the sides of the cavity near the cavity opening. These vortices are generally symmetric about the cavity centre-plane. However, the discovery of a single tornado vortex, located near the cavity centreline at the front of the cavity, indicated that the flow within the cavity is asymmetric. It is postulated that the observed asymmetry in the time-averaged flow field is due to the asymmetry in the instantaneous flow field, which switches between two extremes at large time scales.

Physics of Tip Clearance Flow in Turbomachinery (Keynote Paper)

2002 ◽  
Author(s):  
Masahiro Inoue ◽  
Masato Furukawa
Keyword(s):  
Flow Field ◽  
Physical Interpretation ◽  
Vortex Core ◽  
Vortical Structure ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Flow Phenomena

In a recent advanced aerodynamic design of turbomachinery, the physical interpretation of three-dimensional flow field obtained by a numerical simulation is important for iterative modifications of the blade or impeller geometry. This paper describes an approach to the physical interpretation of the tip clearance flow in turbomachinery. First, typical flow phenomena of the tip clearance flow are outlined for axial and radial compressors, pumps and turbines to help comprehensive understanding of the tip clearance flow. Then, a vortex-core identification method which enables to extract the vortical structure from the complicated flow field is introduced, since elucidation of the vortical structure is essential to the physical interpretation of the tip clearance flow. By use of the vortex-core identification, some interesting phenomena of the tip clearance flows are interpreted, especially focussing on axial flow compressors.

Three Components- and Tomographic-PIV Measurements of a Cyclone Cooling Flow in a Swirl Tube

2013 ◽  
Author(s):  
Christoph Biegger ◽  
Bernhard Weigand ◽  
Alice Cabitza
Keyword(s):  
Flow Field ◽  
Vortex Breakdown ◽  
Tracer Particle ◽  
Three Dimensional ◽  
Axial Flow ◽  
Leading Edge ◽  
Generic Model ◽  
Tube Axis ◽  
Tomographic Piv ◽  
Order Of Magnitude

Swirl cooling is a very efficient method for turbine blade cooling. However, the flow in such a system is quite complicated. In order to gain understanding of the flow structure, the velocity field in a leading edge swirl cooling chamber with two tangential inlet ducts is experimentally studied via Particle Image Velocimetry (PIV). The examined swirl tube is 1 m long and has a diameter of 50 mm. It represents an upscaled generic model of a leading edge swirl chamber. The Reynolds number, defined by the bulk velocity and the swirl tube diameter, ranges from 10,000 to 40,000, and the swirl number is 5.3. Velocity fields are measured in the center plane of the tube axis with stereo- and tomographic-PIV using two and four CCD cameras respectively. Tomographic-PIV is a three-dimensional PIV technique relying on the illumination, recording, reconstruction and cross correlation of a tracer particle distribution in a measurement volume opposed to a plane in stereo-PIV. For statistical analysis 2,000 vector maps are calculated and evaluations show a sample size of 1,000 ensembles is sufficient. Our experiment showed, that the flow field is characterized by a vortex system around the tube axis. Near the tube wall we observed an axial flow towards the outlet with a circumferential velocity component in the same order of magnitude. In contrast the vortex core consists of an axial backflow (vortex breakdown). The gained understanding of the flow field allows to predict regions of enhanced heat transfer in swirl chambers.

Sign in / Sign up

Export Citation Format

Share Document