Turbulent horizontal convection under spatially periodic forcing: a regime governed by interior inertia

2017 ◽  
Vol 831 ◽  
pp. 491-523 ◽  
Author(s):  
Madelaine G. Rosevear ◽  
Bishakhdatta Gayen ◽  
Ross W. Griffiths

Differential heating applied at a single horizontal boundary forces ‘horizontal convection’, even when there is no net heat flux through the boundary. However, almost all studies of horizontal convection have been limited to a special class of problem in which temperature or heat flux differences were applied in only one direction and over the horizontal length of a box (the Rossby problem; Rossby, Deep-Sea Res., vol. 12, 1965, pp. 9–16). These conditions strongly constrain the flow. Here we report laboratory experiments and direct numerical simulations (DNS) extending the results of Griffiths & Gayen (Phys. Rev. Lett., vol. 115, 2015, 204301) for horizontal convection forced by boundary conditions imposed in a two-dimensional periodic array at a horizontal boundary. The experiments use saline and freshwater fluxes at a permeable base with the imposed boundary salinity having a horizontal length scale one quarter of the width of the box. The flow reaches a state in which the net boundary buoyancy flux vanishes and the bulk of the fluid shows an inertial range of turbulence length scales. A regime transition is seen for increasing water depth, from an array of individual coherent plumes on the forcing scale to convection dominated by emergent larger scales of overturning. The DNS explore the analogous thermally forced case with sinusoidal boundary temperature of wavenumber $n=4$, and are used to examine the Rayleigh number ($Ra$) dependence for shallow- and deep-water cases. For shallow water the flow transitions with increasing $Ra$ from laminar to turbulent boundary layer regimes that are familiar from the Rossby problem and which have normalised heat transport scaling as $Nu\sim Ra^{1/5}$ and $Nu\sim (Ra\,Pr)^{1/5}$, with $Nu$ the Nusselt number and $Pr$ the Prandtl number, in this case maintaining a stable array of coherent turbulent plumes. For deep-water and large $Ra$ the laminar scaling transitions to $Nu\sim (Ra\,Pr)^{1/4}$, with the scales of turbulence extending to the dimensions of the box. The $1/4$ power law regime is explained in terms of the momentum of symmetric, inviscid large scales of motion in the interior coupled to diffusive loss of heat through stabilised parts of the boundary layer. The turbulence production is predominantly by shear instability rather than convection, with viscous dissipation distributed throughout the bulk of the fluid. These conditions are not seen in the highly asymmetric flow in the Rossby problem even at Rayleigh numbers up to six orders of magnitude greater than the transition found here. The new inertial interior regime has the rate of supply of available potential energy, and its removal by mixing of density, increasing as $Ra^{5/4}$, which is faster than $Ra^{6/5}$ in the Rossby problem. Irreversible mixing is confined close to the forcing boundary and is very much larger than the viscous dissipation, which is proportional to $Ra$.

2017 ◽  
Vol 823 ◽  
pp. 57-99 ◽  
Author(s):  
Catherine A. Vreugdenhil ◽  
Ross W. Griffiths ◽  
Bishakhdatta Gayen

Convection in a rotating rectangular basin with differential thermal forcing at one horizontal boundary is examined using laboratory experiments. The experiments have an imposed heat flux boundary condition, are at large values of the flux Rayleigh number ($Ra_{F}\sim O(10^{13}{-}10^{14})$ based on the box length $L$), use water with Prandtl number $Pr\approx 4$ and have a small depth to length aspect ratio. The results show the conditions for transition from non-rotating horizontal convection governed by an inertial–buoyancy balance in the thermal boundary layer, to circulation governed by geostrophic flow in the boundary layer. The geostrophic balance constrains mean flow and reduces the heat transport as Nusselt number $Nu\sim (Ra_{F}Ro)^{1/6}$, where $Ro=B^{1/2}/f^{3/2}L$ is the convective Rossby number, $B$ is the imposed buoyancy flux and $f$ is the Coriolis parameter. Thus flow in the geostrophic boundary layer regime is governed by the relative roles of horizontal convective accelerations and Coriolis accelerations, or buoyancy and rotation, in the boundary layer. Experimental evidence suggests that for more rapid rotation there is another transition to a regime in which the momentum budget is dominated by fluctuating vertical accelerations in a region of vortical plumes, which we refer to as a ‘chimney’ following related discussion of regions of deep convection in the ocean. Coupling of the chimney convection in the region of destabilising boundary flux to the diffusive boundary layer of horizontal convection in the region of stabilising boundary flux gives heat transport independent of rotation in this ‘inertial chimney’ regime, and the new scaling $Nu\sim Ra_{F}^{1/4}$. Scaling analysis predicts the transition conditions observed in the experiments, as well as a further ‘geostrophic chimney’ regime in which the vertical plumes are controlled by local geostrophy. When $Ro<10^{-1}$, the convection is also observed to produce a set of large basin-scale gyres at all depths in the time-averaged flow.


2007 ◽  
Vol 581 ◽  
pp. 251-276 ◽  
Author(s):  
G. O. HUGHES ◽  
R. W. GRIFFITHS ◽  
J. C. MULLARNEY ◽  
W. H. PETERSON

We present a simple flow model and solution to describe ‘horizontal convection’ driven by a gradient of temperature or heat flux along one horizontal boundary of a rectangular box. Following laboratory observations of the steady-state convection, the model is based on a localized vertical turbulent plume from a line or point source that is located anywhere within the area of the box and that maintains a stably stratified interior. In contrast to the ‘filling box’ process, the convective circulation involves vertical diffusion in the interior and a stabilizing buoyancy flux distributed over the horizontal boundary. The stabilizing flux forces the density distribution to reach a steady state. The model predictions compare well with previous laboratory data and numerical solutions. In the case of a point source for the plume (the case which best mimics the localized sinking in the large-scale ocean overturning) the thermal boundary layer is much thicker than that given by the two-dimensional boundary layer scaling of H. T. Rossby (Tellus, vol. 50, 1965, p. 242).


2021 ◽  
Vol 11 (6) ◽  
pp. 2593
Author(s):  
Yasir Al-Okbi ◽  
Tze Pei Chong ◽  
Oksana Stalnov

Leading edge serration is now a well-established and effective passive control device for the reduction of turbulence–leading edge interaction noise, and for the suppression of boundary layer separation at high angle of attack. It is envisaged that leading edge blowing could produce the same mechanisms as those produced by a serrated leading edge to enhance the aeroacoustics and aerodynamic performances of aerofoil. Aeroacoustically, injection of mass airflow from the leading edge (against the incoming turbulent flow) can be an effective mechanism to decrease the turbulence intensity, and/or alter the stagnation point. According to classical theory on the aerofoil leading edge noise, there is a potential for the leading edge blowing to reduce the level of turbulence–leading edge interaction noise radiation. Aerodynamically, after the mixing between the injected air and the incoming flow, a shear instability is likely to be triggered owing to the different flow directions. The resulting vortical flow will then propagate along the main flow direction across the aerofoil surface. These vortical flows generated indirectly owing to the leading edge blowing could also be effective to mitigate boundary layer separation at high angle of attack. The objectives of this paper are to validate these hypotheses, and combine the serration and blowing together on the leading edge to harvest further improvement on the aeroacoustics and aerodynamic performances. Results presented in this paper strongly indicate that leading edge blowing, which is an active flow control method, can indeed mimic and even enhance the bio-inspired leading edge serration effectively.


2017 ◽  
Vol 837 ◽  
pp. 341-380 ◽  
Author(s):  
Peter P. Sullivan ◽  
James C. McWilliams

The evolution of upper ocean currents involves a set of complex, poorly understood interactions between submesoscale turbulence (e.g. density fronts and filaments and coherent vortices) and smaller-scale boundary-layer turbulence. Here we simulate the lifecycle of a cold (dense) filament undergoing frontogenesis in the presence of turbulence generated by surface stress and/or buoyancy loss. This phenomenon is examined in large-eddy simulations with resolved turbulent motions in large horizontal domains using${\sim}10^{10}$grid points. Steady winds are oriented in directions perpendicular or parallel to the filament axis. Due to turbulent vertical momentum mixing, cold filaments generate a potent two-celled secondary circulation in the cross-filament plane that is frontogenetic, sharpens the cross-filament buoyancy and horizontal velocity gradients and blocks Ekman buoyancy flux across the cold filament core towards the warm filament edge. Within less than a day, the frontogenesis is arrested at a small width,${\approx}100~\text{m}$, primarily by an enhancement of the turbulence through a small submesoscale, horizontal shear instability of the sharpened filament, followed by a subsequent slow decay of the filament by further turbulent mixing. The boundary-layer turbulence is inhomogeneous and non-stationary in relation to the evolving submesoscale currents and density stratification. The occurrence of frontogenesis and arrest are qualitatively similar with varying stress direction or with convective cooling, but the detailed evolution and flow structure differ among the cases. Thus submesoscale filament frontogenesis caused by boundary-layer turbulence, frontal arrest by frontal instability and frontal decay by forward energy cascade, and turbulent mixing are generic processes in the upper ocean.


Sign in / Sign up

Export Citation Format

Share Document