scholarly journals Injection into boundary layers: solutions beyond the classical form

2017 ◽  
Vol 822 ◽  
pp. 617-639 ◽  
Author(s):  
R. E. Hewitt ◽  
P. W. Duck ◽  
A. J. Williams
Keyword(s):  
Boundary Layer ◽  
Numerical Study ◽  
Flow Direction ◽  
Three Dimensional ◽  
Boundary Region ◽  
Navier Stokes ◽  
Injection Velocity ◽  
Finite Width ◽  
Viscous Effects ◽  
New States

This theoretical and numerical study presents three-dimensional boundary-layer solutions for laminar incompressible flow adjacent to a semi-infinite flat plate, subject to a uniform free-stream speed and injection through the plate surface. The novelty in this case arises from a fully three-dimensional formulation, which also allows for slot injection over a spanwise length scale comparable to the boundary-layer thickness. This approach retains viscous effects in both the spanwise and transverse directions, and effectively results in a parabolised Navier–Stokes system (sometimes referred to as the ‘boundary-region equations’). Any injection profile can be described in this approach, but we restrict attention to three-dimensional states driven by a finite-width slot aligned with the flow direction and self-similar in their downstream development. The classical two-dimensional states are known to only exist up to a critical (‘blow off’) injection amplitude, but the three-dimensional solutions here appear possible for any injection velocity. These new states take the form of low-speed streamwise-aligned streaks whose geometry depends on the amplitude of injection and the spanwise width of the injection slot; intriguingly, although very low wall shear is typically obtained, streamwise flow reversal is not observed, however hard the blowing. Asymptotic descriptions are provided in the limit of increasing slot width and fixed injection velocity, which allow for classification of the solutions according to two bounding injection rates.

Potential Flow Field Generated by Downstream Moving Bars and Propagated on a Turbine Blade at Low Reynolds Number

2011 ◽  
Author(s):  
Ve´ronique Penin ◽  
Pascale Kulisa ◽  
Franc¸ois Bario
Keyword(s):  
Boundary Layer ◽  
Large Scale ◽  
Numerical Study ◽  
Three Dimensional ◽  
Potential Effect ◽  
Navier Stokes ◽  
Turbine Cascade ◽  
Wake Interaction ◽  
Rotor Stator Interaction ◽  
The Stability

During the last few decades, the size and weight of turbo-machinery have been continuously reduced. However, by decreasing the distance between rows, rotor-stator interaction is strengthened. Two interactions now have the same magnitude: wake interaction and potential effect. Studying this effect is essential to understand rotor-stator interactions. Indeed, this phenomenon influences the whole flow, including the boundary layer of the upstream and downstream blades, ergo the stability of the flow and the efficiency of the machine. A large scale turbine cascade followed by a specially designed rotating cylinder system is used. Synchronised velocity LDA measurements on the vane profile show the flow and boundary layer behavior due to the moving bars. To help the general understanding and to corroborate our experimental results, numerical investigations are carried out with an unsteady three dimensional Navier-Stokes code. Moreover, the numerical study informs about the potential disturbance to the whole flow of the cascade.

A Numerical Analysis of the Three-Dimensional Viscous Flow in a Transonic Compressor Rotor and Comparison With Experiment

1987 ◽  
Vol 109 (1) ◽  
pp. 83-90 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Boundary Layer ◽  
Numerical Analysis ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Viscous Effects ◽  
Transonic Compressor ◽  
Compressor Rotor

The numerical analysis of highly loaded transonic compressors continues to be of considerable interest. Although much progress has been made with inviscid analyses, viscous effects can be very significant, especially those associated with shock–boundary layer interactions. While inviscid analyses have been enhanced by the interactive inclusion of blade surf ace boundary layer calculations, it may be better in the long term to develop efficient algorithms to solve the full three-dimensional Navier–Stokes equations. Indeed, it seems that many phenomena of key interest, like tip clearance flows, may only be accessible to a Navier–Stokes solver. The present paper describes a computer program developed for solving the three-dimensional viscous compressible flow equations in turbomachine geometries. The code is applied to the study of the flowfield in an axial-flow transonic compressor rotor with an attempt to resolve the tip clearance flow. The predicted flow is compared with laser anemometry measurements and good agreement is found.

scholarly journals Numerical simulation on the development of periodic three-dimensional disturbances in a supersonic boundary layer

2019 ◽  
Vol 196 ◽  
pp. 00016
Author(s):  
Gleb Kolosov ◽  
Alexander Semenov ◽  
Alexey Yatskikh
Keyword(s):  
Boundary Layer ◽  
Mass Flow ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Small Diameter ◽  
Supersonic Boundary Layer ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Software Complex

The results of a numerical study of the development of periodic pulsations in a supersonic boundary layer on a flat plate are presented at a Mach number of 2.5 and a unit Reynolds number of 8×106 m–1. Using the software complex ANSYS, the complete Navier-Stokes equations were solved. Periodic mass flow disturbances with a frequency of 20 kHz were introduced into the boundary layer through a small-diameter hole on the surface of the model. Downstream the profiles of the longitudinal mass flow pulsations were recorded, and spectral analysis of the data was carried out. The main characteristics of the development of unstable disturbances in both physical and wave spaces are obtained.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

Direct simulation of evolution and control of three-dimensional instabilities in attachment-line boundary layers

1995 ◽  
Vol 291 ◽  
pp. 369-392 ◽  
Author(s):  
Ronald D. Joslin
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Plate Boundary ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Computationally Efficient ◽  
Simulation Results ◽  
Dimensional Simulation ◽  
Attachment Line

The spatial evolution of three-dimensional disturbances in an attachment-line boundary layer is computed by direct numerical simulation of the unsteady, incompressible Navier–Stokes equations. Disturbances are introduced into the boundary layer by harmonic sources that involve unsteady suction and blowing through the wall. Various harmonic-source generators are implemented on or near the attachment line, and the disturbance evolutions are compared. Previous two-dimensional simulation results and nonparallel theory are compared with the present results. The three-dimensional simulation results for disturbances with quasi-two-dimensional features indicate growth rates of only a few percent larger than pure two-dimensional results; however, the results are close enough to enable the use of the more computationally efficient, two-dimensional approach. However, true three-dimensional disturbances are more likely in practice and are more stable than two-dimensional disturbances. Disturbances generated off (but near) the attachment line spread both away from and toward the attachment line as they evolve. The evolution pattern is comparable to wave packets in flat-plate boundary-layer flows. Suction stabilizes the quasi-two-dimensional attachment-line instabilities, and blowing destabilizes these instabilities; these results qualitatively agree with the theory. Furthermore, suction stabilizes the disturbances that develop off the attachment line. Clearly, disturbances that are generated near the attachment line can supply energy to attachment-line instabilities, but suction can be used to stabilize these instabilities.

An Automated CFD Design and Analysis Tool for Inlet-Bleed Systems

1998 ◽  
Author(s):  
Tom I-P. Shih ◽  
Yu-Liang Lin ◽  
Andrew J. Flores ◽  
Mark A. Stephens ◽  
Mark J. Rimlinger ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Incident Shock ◽  
Navier Stokes ◽  
Oblique Shock Wave ◽  
Design Parameters ◽  
Analysis Tool ◽  
Cfd Analysis ◽  
Circular Holes ◽  
Embedded Grids

Abstract A pre-processor was developed to assist CFD experts and non-experts in performing steady, three-dimensional Navier-Stokes analysis of a class of inlet-bleed problems involving oblique shock-wave/ boundary-layer interactions on a flat plate with bleed into a plenum through rows of circular holes. With this pre-processor, once geometry (e.g., hole dimensions and arrangement) and flow conditions (e.g., Mach number, boundary-layer thickness, incident shock location) are inputted, it will automatically generate every file needed to perform a CFD analysis from the grid system to initial and boundary conditions. This is accomplished by accessing a knowledge base established by experts who understand both CFD and the class of problems being analyzed. For experts in CFD, this tool greatly reduces the amount of time and effort needed to setup a problem for CFD analysis. It also provides experts with knobs to make changes to the setup if desired. For non-experts in CFD, this tool enables reliable and correct usage of CFD. A typical session on a workstation from data input to the generation of all files needed to perform a CFD analysis involves less than ten minutes. This pre-processor, referred to as AUTOMAT-V2, is an improved version of a code called AUTOMAT. Improvements made include: (1) multi-block structured grids can be patched in addition to being overlapped; (2) embedded grids can be introduced near bleed holes to reduce the number of grid points/cells needed by a factor of up to four; (3) grid systems generated allow up to three levels of multigrid; (4) CFL3D is supported in addition to OVERFLOW, two well-known and highly regarded Navier-Stokes solvers developed at NASA’s Langley and Ames Research Centers; (5) all files needed to run RONNIE for patched grids and MAGGIE for overlapped grids are also generated; and (6) more design parameters can be investigated including the study of micro bleed and effects of flow/hole misalignments.

A CFD-Based Parametric Study on Modification of Discrete Sister Holes Location for the Film Cooling Flow

2014 ◽  
Author(s):  
Siavash Khajehhasani ◽  
Bassam Jubran
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Base Case ◽  
Spanwise Direction ◽  
Cooling Performance ◽  
Cooling Flow ◽  
Lift Off ◽  
The Individual

A numerical study on the effects of sister holes locations on film cooling performance is presented. This includes the change of the location of the individual discrete sister holes in the streamwise and spanwise directions, where each one of these directions includes 9 different locations, The simulations are performed using three-dimensional Reynolds-Averaged Navier Stokes analysis with the realizable k–ε model combined with the standard wall function. The variation of the sister holes in the streamwise direction provides similar film cooling performance as the base case for both blowing ratios of 0.5 and 1. On the other hand, the spanwise variation of the sister holes’ location has a more prominent effect on the effectiveness. In some cases, as a result of the anti-vortices generated from the sister holes and the repositioning of the sister holes in the spanwise direction, the jet lift-off effect notably decreases and more volume of coolant is distributed in the spanwise direction.

scholarly journals Choice and Limits of a Fluid Model for the Numerical Study in Dynamic Fluid Structure Interaction Problems

2003 ◽  
Author(s):  
Jean Franc¸ois Sigrist ◽  
Christian Laine ◽  
Dominique Lemoine ◽  
Bernard Peseux
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Model ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Linear Solution ◽  
Fluid Structure ◽  
Design Engineers ◽  
Inviscid Incompressible Fluid ◽  
Basic Fluid

This paper is related to the study of a nuclear propulsion reactor prototype for the French Navy. This prototype is built on ground and is to be dimensioned toward seismic loading. The dynamic analysis takes the coupled fluid structure analysis into account. The basic fluid models used by design engineers are inviscid incompressible or compressible. The fluid can be described in a bidimensional by slice or a three-dimensional approach. A numerical study is carried out on a generic problem for the linear FSI dynamic problem. The results of this study are presented and discussed. As a conclusion, the three-dimensional inviscid incompressible fluid appears to be the best compromise between the description of physical phenomena and the cost of modeling. The geometry of the reactor is such that large displacements of the structure in the fluid can occur. Therefore, the linearity hypothesis might not be longer valid. The case of large amplitude imposed oscillating motion of a cylinder in a confined fluid is numerically studied. A CFD code is used to investigate the fluid behavior solving the NAVIER-STOKES equations. The forces induced on the cylinder by the fluid are computed and compared to the linear solution. The limit of the linear model can then be exhibited.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

Turbine Airfoil Heat Transfer Predictions Using CFD

2005 ◽  
Author(s):  
Anil K. Tolpadi ◽  
James A. Tallman ◽  
Lamyaa El-Gabry
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulence Modeling ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Navier Stokes ◽  
Design System ◽  
Computational Fluid Dynamics Cfd ◽  
Turbine Airfoils ◽  
Typical Design

Conventional heat transfer design methods for turbine airfoils use 2-D boundary layer codes (BLC) combined with empiricism. While such methods may be applicable in the mid span of an airfoil, they would not be very accurate near the end-walls and airfoil tip where the flow is very three-dimensional (3-D) and complex. In order to obtain accurate heat transfer predictions along the entire span of a turbine airfoil, 3-D computational fluid dynamics (CFD) must be used. This paper describes the development of a CFD based design system to make heat transfer predictions. A 3-D, compressible, Reynolds-averaged Navier-Stokes CFD solver with k-ω turbulence modeling was used. A wall integration approach was used for boundary layer prediction. First, the numerical approach was validated against a series of fundamental airfoil cases with available data. The comparisons were very favorable. Subsequently, it was applied to a real engine airfoil at typical design conditions. A discussion of the features of the airfoil heat transfer distribution is included.

Sign in / Sign up

Export Citation Format

Share Document