The effect of Reynolds number on mixing in Kelvin–Helmholtz billows

2014 ◽  
Vol 759 ◽  
pp. 612-641 ◽  
Author(s):  
M. Rahmani ◽  
G. A. Lawrence ◽  
B. R. Seymour
Keyword(s):  
Reynolds Number ◽  
Large Scale ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Mixing Efficiency ◽  
Laboratory Measurements ◽  
Flow Properties ◽  
Low Reynolds Numbers ◽  
Vortex Pairing ◽  
High Reynolds

AbstractMixing induced through the life-cycle of Kelvin–Helmholtz (KH) billows is studied for a range of low and intermediate Reynolds numbers using direct numerical simulations (DNS). The amount of stirring, and therefore mixing, is significantly controlled by the process of vortex pairing of two KH billows. For low Reynolds numbers, vortex pairing of the billows is complete in the pre-turbulent stage or early stages of turbulence, generating a high amount of stirring. At higher Reynolds numbers, vortex pairing is suppressed by the growth of three-dimensional instabilities, and the amount of stirring is significantly reduced. For single KH billows, as the Reynolds number increases, there is a transition in the characteristics of the mixing, similar to the laboratory measurements of Breidenthal (J. Fluid Mech., vol. 109, 1981, pp. 1–24) and Koochesfahani & Dimotakis (J. Fluid Mech., vol. 170, 1986, pp. 83–112). The transition in mixing is associated with the growth and sustainability of three-dimensional motions at sufficiently high Reynolds numbers. We examine this ‘mixing transition’ and the influence of vortex pairing on it by examining the flow properties at different stages and the exchange between the energy partitions. As the Reynolds number increases, three-dimensional motions develop over a wider range of length scales, and smaller scale eddies form. However, this does not necessarily result in a greater amount of mixing. The maximum total amount of mixing induced over the lifetime of a KH instability, for billows both with and without vortex pairing, occurs when the large-scale eddies that cause the stirring are the most energetic. The mixing efficiency reveals a non-monotonic dependence on the Reynolds number.

An Investigation of Factors Influencing the Calibration of Five-Hole Probes for Three-Dimensional Flow Measurements

1993 ◽  
Vol 115 (3) ◽  
pp. 513-519 ◽  
Author(s):  
R. G. Dominy ◽  
H. P. Hodson
Keyword(s):  
Reynolds Number ◽  
Large Scale ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Flow Measurements ◽  
Low Reynolds Numbers ◽  
Additional Information ◽  
Reynolds Number Effects ◽  
Low Speed Wind Tunnel ◽  
Probe Head

The effects of Reynolds number, Mach number, and turbulence on the calibrations of commonly used types of five-hole probe are discussed. The majority of the probes were calibrated at the exit from a transonic nozzle over a range of Reynolds numbers (7 × 103 < Re < 80 × 103 based on probe tip diameter) at subsonic and transonic Mach numbers. Additional information relating to the flow structure were obtained from a large-scale, low-speed wind tunnel. The results confirmed the existence of two distinct Reynolds number effects. Flow separation around the probe head affects the calibrations at relatively low Reynolds numbers while changes in the detailed structure of the flow around the sensing holes affects the calibrations even when the probe is nulled. Compressibility is shown to have little influence upon the general behavior of these probes in terms of Reynolds number sensitivity but turbulence can affect the reliability of probe calibrations at typical test Reynolds numbers.

Turbulent flow between counter-rotating concentric cylinders: a direct numerical simulation study

2008 ◽  
Vol 615 ◽  
pp. 371-399 ◽  
Author(s):  
S. DONG
Keyword(s):  
Turbulent Flow ◽  
Large Scale ◽  
Outer Cylinder ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Taylor Vortex ◽  
Small Scale ◽  
Mean Flow ◽  
Concentric Cylinders ◽  
High Reynolds

We report three-dimensional direct numerical simulations of the turbulent flow between counter-rotating concentric cylinders with a radius ratio 0.5. The inner- and outer-cylinder Reynolds numbers have the same magnitude, which ranges from 500 to 4000 in the simulations. We show that with the increase of Reynolds number, the prevailing structures in the flow are azimuthal vortices with scales much smaller than the cylinder gap. At high Reynolds numbers, while the instantaneous small-scale vortices permeate the entire domain, the large-scale Taylor vortex motions manifested by the time-averaged field do not penetrate a layer of fluid near the outer cylinder. Comparisons between the standard Taylor–Couette system (rotating inner cylinder, fixed outer cylinder) and the counter-rotating system demonstrate the profound effects of the Coriolis force on the mean flow and other statistical quantities. The dynamical and statistical features of the flow have been investigated in detail.

Experimental characterization of three-dimensional corner flows at low Reynolds numbers

2012 ◽  
Vol 707 ◽  
pp. 37-52 ◽  
Author(s):  
J. Sznitman ◽  
L. Guglielmini ◽  
D. Clifton ◽  
D. Scobee ◽  
H. A. Stone ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Channel Cross Section ◽  
Experimental Characterization ◽  
Low Reynolds Numbers ◽  
Low Reynolds

AbstractWe investigate experimentally the characteristics of the flow field that develops at low Reynolds numbers ($\mathit{Re}\ll 1$) around a sharp $9{0}^{\ensuremath{\circ} } $ corner bounded by channel walls. Two-dimensional planar velocity fields are obtained using particle image velocimetry (PIV) conducted in a towing tank filled with a silicone oil of high viscosity. We find that, in the vicinity of the corner, the steady-state flow patterns bear the signature of a three-dimensional secondary flow, characterized by counter-rotating pairs of streamwise vortical structures and identified by the presence of non-vanishing transverse velocities (${u}_{z} $). These results are compared to numerical solutions of the incompressible flow as well as to predictions obtained, for a similar geometry, from an asymptotic expansion solution (Guglielmini et al., J. Fluid Mech., vol. 668, 2011, pp. 33–57). Furthermore, we discuss the influence of both Reynolds number and aspect ratio of the channel cross-section on the resulting secondary flows. This work represents, to the best of our knowledge, the first experimental characterization of the three-dimensional flow features arising in a pressure-driven flow near a corner at low Reynolds number.

Reynolds Number Effects on the Freewheeling Behavior of a High Solidity Vertical River Kinetic Turbine

2010 ◽  
Author(s):  
Amir Hossein Birjandi ◽  
Eric Bibeau
Keyword(s):  
Reynolds Number ◽  
Reynolds Numbers ◽  
Speed Ratio ◽  
Stream Velocity ◽  
Blade Profile ◽  
Low Reynolds Numbers ◽  
Tip Speed Ratio ◽  
Reynolds Number Effects ◽  
High Reynolds ◽  
The University

A four-bladed, squirrel-cage, and scaled vertical kinetic turbine was designed, instrumented and tested in the water tunnel facilities at the University of Manitoba. With a solidity of 1.3 and NACA0021 blade profile, the turbine is classified as a high solidity model. Results were obtained for conditions during freewheeling at various Reynolds numbers. In this study, the freewheeling tip speed ratio, which relates the ratio of maximum blade speed to the free stream velocity at no load, was divided into three regions based on the Reynolds number. At low Reynolds numbers, the tip speed ratio was lower than unity and blades were in a stall condition. At the end of the first region, there was a sharp increase of the tip speed ratio so the second region has a tip speed ratio significantly higher than unity. In this region, the tip speed ratio increases almost linearly with Reynolds number. At high Reynolds numbers, the tip speed ratio is almost independent of Reynolds number in the third region. It should be noted that the transition between these three regions is a function of the blade profile and solidity. However, the three-region behavior is applicable to turbines with different profiles and solidities.

Coherent structures in coflowing jets and wakes

1978 ◽  
Vol 88 (3) ◽  
pp. 451-463 ◽  
Author(s):  
A. E. Perry ◽  
T. T. Lim
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Glass Tube ◽  
Reynolds Numbers ◽  
Reynolds Number Flow ◽  
Naturally Occurring ◽  
Number Flow ◽  
High Reynolds ◽  
Scale Motion

By applying small lateral oscillations to a glass tube from which smoke was issuing, perfectly periodic coflowing jets and wake structures were produced at Reynolds numbers of order 300-1000. These structures remained coherent over long streamwise distances and appeared to be perfectly frozen when viewed under stroboscopic light which was synchronized with the disturbing oscillation. By the use of strobing laser beams, longitudinal sections of the structures were photographed and an account of the geometry of these structures is reported.When the tube was unforced, similar structures occurred but they modulated in scale and frequency, and their orientation was random.A classification of structures is presented and examples are demonstrated in naturally occurring situations such as smoke from a cigarette, the wake behind a three-dimensional blunt body, and the high Reynolds number flow in a plume from a chimney. It is suggested that an examination of these structures may give some insight into the large-scale motion in fully turbulent flow.

On High-Performance Airfoil at Very Low Reynolds Number

2016 ◽  
Vol 28 (3) ◽  
pp. 273-285
Author(s):  
Katsuya Hirata ◽  
◽  
Ryo Nozawa ◽  
Shogo Kondo ◽  
Kazuki Onishi ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
High Performance ◽  
Low Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Slow Flow ◽  
Low Reynolds Numbers ◽  
Low Reynolds

[abstFig src='/00280003/02.jpg' width=""300"" text='Iso-Q surfaces of very-slow flow past an iNACA0015' ] The airfoil is often used as the elemental device for flying/swimming robots, determining its basic performances. However, most of the aerodynamic characteristics of the airfoil have been investigated at Reynolds numbers Re’s more than 106. On the other hand, our knowledge is not enough in low Reynolds-number ranges, in spite of the recent miniaturisation of robots. In the present study, referring to our previous findings (Hirata et al., 2011), we numerically examine three kinds of high-performance airfoils proposed for very-low Reynolds numbers; namely, an iNACA0015 (the NACA0015 placed back to front), an FPBi (a flat plate blended with iNACA0015 as its upper half) and an FPBN (a flat plate blended with the NACA0015 as its upper half), in comparison with such basic airfoils as a NACA0015 and an FP (a flat plate), at a Reynolds number Re = 1.0 × 102 using two- and three-dimensional computations. As a result, the FPBi shows the best performance among the five kinds of airfoils.

Flow separation on a spheroid at incidence

1979 ◽  
Vol 92 (4) ◽  
pp. 643-657 ◽  
Author(s):  
Taeyoung Han ◽  
V. C. Patel
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Inviscid Flow ◽  
Reynolds Numbers ◽  
Surface Flow ◽  
Laminar Separation ◽  
Low Reynolds Numbers ◽  
Turbulent Separation

Surface streamline patterns on a spheroid have been examined at several angles of attack. Most of the tests were performed at low Reynolds numbers in a hydraulic flume using coloured dye to make the surface flow visible. A limited number of experiments was also carried out in a wind tunnel, using wool tufts, to study the influence of Reynolds number and turbulent separation. The study has verified some of the important qualitative features of three-dimensional separation criteria proposed earlier by Maskell, Wang and others. The observed locations of laminar separation lines on a spheroid at various incidences have been compared with the numerical solutions of Wang and show qualitative agreement. The quantitative differences are attributed largely to the significant viscous-inviscid flow interaction which is present, especially at large incidences.

Low Reynolds numbers flow past an ellipsoid of revolution of large aspect ratio

1965 ◽  
Vol 23 (4) ◽  
pp. 657-671 ◽  
Author(s):  
Yun-Yuan Shi
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Three Dimensional ◽  
Major Axis ◽  
Reynolds Numbers ◽  
The Body ◽  
Large Aspect Ratio ◽  
Low Reynolds Numbers ◽  
Ellipsoid Of Revolution ◽  
Limiting Case

The results of Proudman & Pearson (1957) and Kaplun & Lagerstrom (1957) for a sphere and a cylinder are generalized to study an ellipsoid of revolution of large aspect ratio with its axis of revolution perpendicular to the uniform flow at infinity. The limiting case, where the Reynolds number based on the minor axis of the ellipsoid is small while the other Reynolds number based on the major axis is fixed, is studied. The following points are deduced: (1) although the body is three-dimensional the expansion is in inverse power of the logarithm of the Reynolds number as the case of a two-dimensional circular cylinder; (2) the existence of the ends and the variation of the diameter along the axis of revolution have no effect on the drag to the first order; (3) a formula for drag is obtained to higher order.

scholarly journals Reynolds number trend of hierarchies and scale interactions in turbulent boundary layers

2017 ◽  
Vol 375 (2089) ◽  
pp. 20160077 ◽  
Author(s):  
W. J. Baars ◽  
N. Hutchins ◽  
I. Marusic
Keyword(s):  
Reynolds Number ◽  
Large Scale ◽  
Reynolds Numbers ◽  
Shear Layers ◽  
Wall Turbulence ◽  
Small Scale ◽  
Velocity Fluctuations ◽  
Scale Interaction ◽  
High Reynolds ◽  
Near Wall

Small-scale velocity fluctuations in turbulent boundary layers are often coupled with the larger-scale motions. Studying the nature and extent of this scale interaction allows for a statistically representative description of the small scales over a time scale of the larger, coherent scales. In this study, we consider temporal data from hot-wire anemometry at Reynolds numbers ranging from Re τ ≈2800 to 22 800, in order to reveal how the scale interaction varies with Reynolds number. Large-scale conditional views of the representative amplitude and frequency of the small-scale turbulence, relative to the large-scale features, complement the existing consensus on large-scale modulation of the small-scale dynamics in the near-wall region. Modulation is a type of scale interaction, where the amplitude of the small-scale fluctuations is continuously proportional to the near-wall footprint of the large-scale velocity fluctuations. Aside from this amplitude modulation phenomenon, we reveal the influence of the large-scale motions on the characteristic frequency of the small scales, known as frequency modulation. From the wall-normal trends in the conditional averages of the small-scale properties, it is revealed how the near-wall modulation transitions to an intermittent-type scale arrangement in the log-region. On average, the amplitude of the small-scale velocity fluctuations only deviates from its mean value in a confined temporal domain, the duration of which is fixed in terms of the local Taylor time scale. These concentrated temporal regions are centred on the internal shear layers of the large-scale uniform momentum zones, which exhibit regions of positive and negative streamwise velocity fluctuations. With an increasing scale separation at high Reynolds numbers, this interaction pattern encompasses the features found in studies on internal shear layers and concentrated vorticity fluctuations in high-Reynolds-number wall turbulence. This article is part of the themed issue ‘Toward the development of high-fidelity models of wall turbulence at large Reynolds number’.

The Effect of Reynolds Number on the Performance of a Tangential-Flow Turbine

1965 ◽  
Author(s):  
Robert G. Adams
Keyword(s):  
Reynolds Number ◽  
Power Systems ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Theoretical Determination ◽  
Low Reynolds Numbers ◽  
Tangential Flow ◽  
Circulatory Flow ◽  
Reasonable Prediction

The tangential-flow turbine, which was developed from the drag turbine in an effort to take advantage of the circulatory flow in the drag-turbine passages, frequently has been proposed for use in power systems characterized by low specific speeds. Since such systems often operate with low exhaust pressures which lead to low Reynolds numbers in turbine passages, it is of interest to determine the effect of Reynolds number on the performance of this type of machine. Theoretical determination of the effect is made difficult by the complex three-dimensional nature of the flow in this type of turbine. This paper describes a program of tests which was run on a tangential-flow turbine to investigate the effect of Reynolds number, and presents a simplified theoretical approach to the Reynolds-number effect which is shown to give a reasonable prediction of the trend of the effect.

Sign in / Sign up

Export Citation Format

Share Document