scholarly journals Turbulent boundary layers over permeable walls: scaling and near-wall structure

2011 ◽  
Vol 687 ◽  
pp. 141-170 ◽  
Author(s):  
C. Manes ◽  
D. Poggi ◽  
L. Ridolfi

AbstractThis paper presents an experimental study devoted to investigating the effects of permeability on wall turbulence. Velocity measurements were performed by means of laser Doppler anemometry in open channel flows over walls characterized by a wide range of permeability. Previous studies proposed that the von Kármán coefficient associated with mean velocity profiles over permeable walls is significantly lower than the standard values reported for flows over smooth and rough walls. Furthermore, it was observed that turbulent flows over permeable walls do not fully respect the widely accepted paradigm of outer-layer similarity. Our data suggest that both anomalies can be explained as an effect of poor inner–outer scale separation if the depth of shear penetration within the permeable wall is considered as the representative length scale of the inner layer. We observed that with increasing permeability, the near-wall structure progressively evolves towards a more organized state until it reaches the condition of a perturbed mixing layer where the shear instability of the inflectional mean velocity profile dictates the scale of the dominant eddies. In our experiments such shear instability eddies were detected only over the wall with the highest permeability. In contrast attached eddies were present over all the other wall conditions. On the basis of these findings, we argue that the near-wall structure of turbulent flows over permeable walls is regulated by a competing mechanism between attached and shear instability eddies. We also argue that the ratio between the shear penetration depth and the boundary layer thickness quantifies the ratio between such eddy scales and, therefore, can be used as a diagnostic parameter to assess which eddy structure dominates the near-wall region for different wall permeability and flow conditions.

2012 ◽  
Vol 550-553 ◽  
pp. 2014-2018
Author(s):  
Xiao Lan Zhou ◽  
Cai Xi Liu ◽  
Yu Hong Dong

Electrochemical mass transfer in turbulent flows and binary electrolytes is investigated. The primary objective is to provide information about mass transfer in the near-wall region between a solid boundary and a turbulent fluid flow at different Schmidt numbers. Based on the computational fluid dynamics and electrochemistry theories, a model for turbulent electrodes channel flow is established. The turbulent mass transfer in electrolytic processes has been predicted by the direct numerical simulation method under limiting current and galvanostatic conditions, we investigate mean concentration and the structure of the concentration fluctuating filed for different Schmidt numbers from 0.1 to 100 .The effect of different concentration boundary conditions at the electrodes on the near-wall turbulence statistics is also discussed.


2017 ◽  
Vol 822 ◽  
pp. 186-201 ◽  
Author(s):  
Kazuhiko Suga ◽  
Yuka Nakagawa ◽  
Masayuki Kaneda

Spanwise flow field measurements are carried out for turbulent flows in channels with permeable bottom walls by particle image velocimetry (PIV) to understand the effects of the wall permeability on turbulence structure near porous walls. The porous media used are three kinds of foamed ceramics which have the same porosities (0.8) but different permeabilities. The turbulent flow fields in spanwise planes are discussed using instantaneous and statistical measurement data. At a small permeability Reynolds number ($Re_{K}$), low-speed and high-speed streaks, which are similar to those of solid-wall turbulence, are observed near the walls while at a large $Re_{K}$ the observed structure is very different from that of the solid-wall turbulence. It is found that the obtained spanwise scales of the structure can be reasonably correlated with the wall normal distance plus the zero-plane displacement which is estimated from the mean velocity profile. With the distribution profiles of the spanwise streak spacing and integral length scales, the transitional change of the turbulence structure over permeable walls is discussed.


2012 ◽  
Vol 699 ◽  
pp. 50-78 ◽  
Author(s):  
G. Sardina ◽  
P. Schlatter ◽  
L. Brandt ◽  
F. Picano ◽  
C. M. Casciola

AbstractWe study the two main phenomenologies associated with the transport of inertial particles in turbulent flows, turbophoresis and small-scale clustering. Turbophoresis describes the turbulence-induced wall accumulation of particles dispersed in wall turbulence, while small-scale clustering is a form of local segregation that affects the particle distribution in the presence of fine-scale turbulence. Despite the fact that the two aspects are usually addressed separately, this paper shows that they occur simultaneously in wall-bounded flows, where they represent different aspects of the same process. We study these phenomena by post-processing data from a direct numerical simulation of turbulent channel flow with different populations of inertial particles. It is shown that artificial domain truncation can easily alter the mean particle concentration profile, unless the domain is large enough to exclude possible correlation of the turbulence and the near-wall particle aggregates. The data show a strong link between accumulation level and clustering intensity in the near-wall region. At statistical steady state, most accumulating particles aggregate in strongly directional and almost filamentary structures, as found by considering suitable two-point observables able to extract clustering intensity and anisotropy. The analysis provides quantitative indications of the wall-segregation process as a function of the particle inertia. It is shown that, although the most wall-accumulating particles are too heavy to segregate in homogeneous turbulence, they exhibit the most intense local small-scale clustering near the wall as measured by the singularity exponent of the particle pair correlation function.


1995 ◽  
Vol 287 ◽  
pp. 317-348 ◽  
Author(s):  
James M. Hamilton ◽  
John Kim ◽  
Fabian Waleffe

Direct numerical simulations of a highly constrained plane Couette flow are employed to study the dynamics of the structures found in the near-wall region of turbulent flows. Starting from a fully developed turbulent flow, the dimensions of the computational domain are reduced to near the minimum values which will sustain turbulence. A remarkably well-defined, quasi-cyclic and spatially organized process of regeneration of near-wall structures is observed. This process is composed of three distinct phases: formation of streaks by streamwise vortices, breakdown of the streaks, and regeneration of the streamwise vortices. Each phase sets the stage for the next, and these processes are analysed in detail. The most novel results concern vortex regeneration, which is found to be a direct result of the breakdown of streaks that were originally formed by the vortices, and particular emphasis is placed on this process. The spanwise width of the computational domain corresponds closely to the typically observed spanwise spacing of near-wall streaks. When the width of the domain is further reduced, turbulence is no longer sustained. It is suggested that the observed spacing arises because the time scales of streak formation, breakdown and vortex regeneration become mismatched when the streak spacing is too small, and the regeneration cycle at that scale is broken.


2013 ◽  
Vol 723 ◽  
pp. 126-139 ◽  
Author(s):  
Farid Karimpour ◽  
Subhas K. Venayagamoorthy

AbstractIn this paper, we revisit the eddy viscosity formulation to highlight a number of important issues that have direct implications for the prediction of near-wall turbulence. For steady wall-bounded turbulent flows, we make the equilibrium assumption between rates of production ($P$) and dissipation ($\epsilon $) of turbulent kinetic energy ($k$) in the near-wall region to propose that the eddy viscosity should be given by ${\nu }_{t} \approx \epsilon / {S}^{2} $, where $S$ is the mean shear rate. We then argue that the appropriate velocity scale is given by $\mathop{(S{T}_{L} )}\nolimits ^{- 1/ 2} {k}^{1/ 2} $ where ${T}_{L} = k/ \epsilon $ is the turbulence (decay) time scale. The difference between this velocity scale and the commonly assumed velocity scale of ${k}^{1/ 2} $ is subtle but the consequences are significant for near-wall effects. We then extend our discussion to show that the fundamental length and time scales that capture the near-wall behaviour in wall-bounded shear flows are the shear mixing length scale ${L}_{S} = \mathop{(\epsilon / {S}^{3} )}\nolimits ^{1/ 2} $ and the mean shear time scale $1/ S$, respectively. With these appropriate length and time scales (or equivalently velocity and time scales), the eddy viscosity can be rewritten in the familiar form of the $k$–$\epsilon $ model as ${\nu }_{t} = \mathop{(1/ S{T}_{L} )}\nolimits ^{2} {k}^{2} / \epsilon $. We use the direct numerical simulation (DNS) data of turbulent channel flow of Hoyas & Jiménez (Phys. Fluids, vol. 18, 2006, 011702) and the turbulent boundary layer flow of Jiménez et al. (J. Fluid Mech. vol. 657, 2010, pp. 335–360) to perform ‘a priori’ tests to check the validity of the revised eddy viscosity formulation. The comparisons with the exact computations from the DNS data are remarkable and highlight how well the equilibrium assumption holds in the near-wall region. These findings could prove to be useful in near-wall modelling of turbulent flows.


2016 ◽  
Vol 796 ◽  
pp. 417-436 ◽  
Author(s):  
A. Cimarelli ◽  
E. De Angelis ◽  
J. Jiménez ◽  
C. M. Casciola

The present work describes the multidimensional behaviour of scale-energy production, transfer and dissipation in wall-bounded turbulent flows. This approach allows us to understand the cascade mechanisms by which scale energy is transmitted scale-by-scale among different regions of the flow. Two driving mechanisms are identified. A strong scale-energy source in the buffer layer related to the near-wall cycle and an outer scale-energy source associated with an outer turbulent cycle in the overlap layer. These two sourcing mechanisms lead to a complex redistribution of scale energy where spatially evolving reverse and forward cascades coexist. From a hierarchy of spanwise scales in the near-wall region generated through a reverse cascade and local turbulent generation processes, scale energy is transferred towards the bulk, flowing through the attached scales of motion, while among the detached scales it converges towards small scales, still ascending towards the channel centre. The attached scales of wall-bounded turbulence are then recognized to sustain a spatial reverse cascade process towards the bulk flow. On the other hand, the detached scales are involved in a direct forward cascade process that links the scale-energy excess at large attached scales with dissipation at the smaller scales of motion located further away from the wall. The unexpected behaviour of the fluxes and of the turbulent generation mechanisms may have strong repercussions on both theoretical and modelling approaches to wall turbulence. Indeed, actual turbulent flows are shown here to have a much richer physics with respect to the classical notion of turbulent cascade, where anisotropic production and inhomogeneous fluxes lead to a complex redistribution of energy where a spatial reverse cascade plays a central role.


2013 ◽  
Vol 715 ◽  
pp. 436-451 ◽  
Author(s):  
A. Cimarelli ◽  
E. De Angelis ◽  
C. M. Casciola

AbstractThe paper describes the energy fluxes simultaneously occurring in the space of scales and in the physical space of wall-turbulent flows. The unexpected behaviour of the energy fluxes consists of spiral-like paths in the combined physical/scale space where the controversial reverse energy cascade plays a central role. Two dynamical processes are identified as driving mechanisms for the fluxes, one in the near-wall region and a second one further away from the wall. The former, stronger, one is related to the dynamics involved in the near-wall turbulence regeneration cycle. The second suggests an outer self-sustaining mechanism which is asymptotically expected to take place in the eventual log layer and could explain the debated mixed inner/outer scaling of the near-wall statistics. The observed behaviour may have strong repercussions on both theoretical and modelling approaches to wall turbulence, as anticipated by a simple equation which is shown able to capture most of the rich dynamics of the shear-dominated region of the flow.


1991 ◽  
Vol 113 (1) ◽  
pp. 34-41 ◽  
Author(s):  
G. J. Yoo ◽  
R. M. C. So ◽  
B. C. Hwang

Internal rotating boundary-layer flows are strongly influenced by large circumferential strain and the turbulence field is anisotropic. This is especially true in the entry region of a rotating pipe where the flow is three dimensional, the centrifugal force due to fluid rotation is less important, and the circumferential strain created by surface rotation has a significant effect on the turbulence field near the wall. Consequently, viscous effects cannot be neglected in the near-wall region. Several low-Reynolds-number turbulence closures are proposed for the calculation of developing rotating pipe flows. Some are two-equation closures with and without algebraic stress correction, while others are full Reynolds-stress closures. It is found that two-equation closures with and without algebraic stress correction are totally inadequate for this three-dimensional flow, while Reynolds-stress closures give results that are in good agreement with measurements over a wide range of rotation numbers.


2019 ◽  
Vol 872 ◽  
pp. 367-406 ◽  
Author(s):  
Kee Onn Fong ◽  
Omid Amili ◽  
Filippo Coletti

We present experimental observations of the velocity and spatial distribution of inertial particles dispersed in turbulent downward flow through a vertical channel at friction Reynolds numbers $\mathit{Re}_{\unicode[STIX]{x1D70F}}=235$ and 335. The working fluid is air laden with size-selected glass microspheres, having Stokes numbers $St=\mathit{O}(10)$ and $\mathit{O}(100)$ when based on the Kolmogorov and viscous time scales, respectively. Cases at solid volume fractions $\unicode[STIX]{x1D719}_{v}=3\times 10^{-6}$ and $5\times 10^{-5}$ are considered. In the more dilute regime, the particle concentration profile shows near-wall and centreline maxima compatible with a turbophoretic drift down the gradient of turbulence intensity; the particles travel at speed similar to that of the unladen flow except in the near-wall region; and their velocity fluctuations generally follow the unladen flow level over the channel core, exceeding it in the near-wall region. The denser regime presents substantial differences in all measured statistics: the near-wall concentration peak is much more pronounced, while the centreline maximum is absent; the mean particle velocity decreases over the logarithmic and buffer layers; and particle velocity fluctuations and deposition velocities are enhanced. An analysis of the spatial distributions of particle positions and velocities reveals different behaviours in the core and near-wall regions. In the channel core, dense clusters form which are somewhat elongated, tend to be preferentially aligned with the vertical/streamwise direction and travel faster than the less concentrated particles. In the near-wall region, the particles arrange in highly elongated streaks associated with negative streamwise velocity fluctuations, several channel heights in length and spaced by $\mathit{O}(100)$ wall units, supporting the view that these are coupled to fluid low-speed streaks typical of wall turbulence. The particle velocity fields contain a significant component of random uncorrelated motion, more prominent for higher $St$ and in the near-wall region.


2019 ◽  
Vol 36 (1) ◽  
pp. 12-21 ◽  
Author(s):  
Xiaotong Cui ◽  
Nan Jiang ◽  
Xiaobo Zheng ◽  
Zhanqi Tang

Abstract This study experimentally investigates the impact of a single piezoelectric (PZT) actuator on a turbulent boundary layer from a statistical viewpoint. The working conditions of the actuator include a range of frequencies and amplitudes. The streamwise velocity signals in the turbulent boundary layer flow are measured downstream of the actuator using a hot-wire anemometer. The mean velocity profiles and other basic parameters are reported. Spectra results obtained by discrete wavelet decomposition indicate that the PZT vibration primarily influences the near-wall region. The turbulent intensities at different scales suggest that the actuator redistributes the near-wall turbulent energy. The skewness and flatness distributions show that the actuator effectively alters the sweep events and reduces intermittency at smaller scales. Moreover, under the impact of the PZT actuator, the symmetry of vibration scales’ velocity signals is promoted and the structural composition appears in an orderly manner. Probability distribution function results indicate that perturbation causes the fluctuations in vibration scales and smaller scales with high intensity and low intermittency. Based on the flatness factor, the bursting process is also detected. The vibrations reduce the relative intensities of the burst events, indicating that the streamwise vortices in the buffer layer experience direct interference due to the PZT control.


Sign in / Sign up

Export Citation Format

Share Document