scholarly journals Algebraically diverging modes upstream of a swept bluff body

2011 ◽  
Vol 683 ◽  
pp. 346-356 ◽  
Author(s):  
Dominik Obrist ◽  
Peter J. Schmid
Keyword(s):  
Boundary Layer ◽  
Bluff Body ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Base Flow ◽  
Algebraic Decay ◽  
Classical Stability ◽  
Dimensional Boundary ◽  
Valid Solution

AbstractClassical stability theory for swept leading-edge boundary layers predicts eigenmodes in the free stream with algebraic decay far from the leading edge. In this article, we extend the classical base flow solution by Hiemenz to a uniformly valid solution for the flow upstream of a bluff body, which includes a three-dimensional boundary layer, an inviscid stagnation-point flow and an outer parallel flow. This extended, uniformly valid base flow additionally supports modes which diverge algebraically outside the boundary layer. The theory of wave packet pseudomodes is employed to derive analytical results for the growth rates and for the eigenvalue spectra of this type of mode. The complete spectral analysis of the flow, including the algebraically diverging modes, will give a more appropriate basis for receptivity studies and will more accurately describe the interaction of perturbations in the free stream with disturbances in the boundary layer.

Receptivity mechanisms in three-dimensional boundary-layer flows

2009 ◽  
Vol 618 ◽  
pp. 209-241 ◽  
Author(s):  
LARS-UVE SCHRADER ◽  
LUCA BRANDT ◽  
DAN S. HENNINGSON
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Nonlinear Process ◽  
Transition To Turbulence ◽  
Boundary Layer Flows ◽  
Free Stream Turbulence ◽  
Dimensional Boundary ◽  
Layer Flow

Receptivity in three-dimensional boundary-layer flow to localized surface roughness and free-stream vorticity is studied. A boundary layer of Falkner–Skan–Cooke type with favourable pressure gradient is considered to model the flow slightly downstream of a swept-wing leading edge. In this region, stationary and travelling crossflow instability dominates over other instability types. Three scenarios are investigated: the presence of low-amplitude chordwise localized, spanwise periodic roughness elements on the plate, the impingement of a weak vortical free-stream mode on the boundary layer and the combination of both disturbance sources. Three receptivity mechanisms are identified: steady receptivity to roughness, unsteady receptivity to free-stream vorticity and unsteady receptivity to vortical modes scattered at the roughness. Both roughness and vortical modes provide efficient direct receptivity mechanisms for stationary and travelling crossflow instabilities. We find that stationary crossflow modes dominate for free-stream turbulence below a level of about 0.5%, whereas higher turbulence levels will promote the unsteady receptivity mechanism. Under the assumption of small amplitudes of the roughness and the free-stream disturbance, the unsteady receptivity process due to scattering of free-stream vorticity at the roughness has been found to give small initial disturbance amplitudes in comparison to the direct mechanism for free-stream modes. However, in many environments free-stream vorticity and roughness may excite interacting unstable stationary and travelling crossflow waves. This nonlinear process may rapidly lead to large disturbance amplitudes and promote transition to turbulence.

Stationary crossflow vortices near the leading edge of three-dimensional boundary layers: the role of non-parallelism and excitation by surface roughness

2018 ◽  
Vol 845 ◽  
pp. 93-140 ◽  
Author(s):  
Adam Butler ◽  
Xuesong Wu
Keyword(s):  
Boundary Layer ◽  
Growth Rate ◽  
Surface Roughness ◽  
Three Dimensional ◽  
Leading Edge ◽  
Base Flow ◽  
Leading Order ◽  
Roughness Elements ◽  
Dimensional Boundary ◽  
Lower Deck

Non-parallelism, i.e. the effect of the slow variation of the boundary-layer flow in the chordwise and spanwise directions, in general produces a higher-order correction to the growth rate of instability modes. Here we investigate stationary crossflow vortices, which arise due to the instability of the three-dimensional boundary layer over a swept wing, focusing on a region near the leading edge where non-parallelism plays a leading-order role in their development. In this regime, the vortices align themselves with the local wall shear at leading order, and so have a marginally separated triple-deck structure, consisting of the inviscid main boundary layer, an upper deck and a viscous sublayer. We find that the streamwise (and spanwise) variations of both the base flow and the modal shape must be accounted for. An explicit expression for the growth rate is derived that shows a neutral point occurs in this regime, downstream of which non-parallelism has a stabilising effect. Stationary crossflow vortices thus have a viscous and non-parallel genesis near the leading edge. If an ‘effective pressure minimum’ occurs within this region then the growth rate becomes unbounded, and so the previous analysis is regularised within a localised region around it. A new instability is identified. The mode maintains its three-tiered structure, but the pressure perturbation now plays a passive role. Downstream, the instability evolves into a Cowley, Hocking & Tutty (Phys. Fluids, vol. 28, 1985, pp. 441–443) instability associated with a critical layer located in the lower deck. Finally, we consider the receptivity of the flow in the non-parallel regime: generation of stationary crossflow modes by arrays of chordwise-localised, spanwise-periodic surface roughness elements. The flow responds differently to different Fourier spectral content of the roughness, giving the lower deck a two-part structure. We find that roughness elements with sharper edges generate stronger modes. For roughness elements of fairly moderate height, the resulting nonlinear forcing leads to the so-called super-linearity of receptivity, namely, the amplitude of the generated crossflow mode deviates from the linear dependence on the roughness height even though the perturbation in the boundary layer remains linear.

Experimental and Theoretical Investigation of the Supersonic Boundary Layer Stability on the Swept Wing

2008 ◽  
Vol 3 (3) ◽  
pp. 34-38
Author(s):  
Sergey A. Gaponov ◽  
Yuri G. Yermolaev ◽  
Aleksandr D. Kosinov ◽  
Nikolay V. Semionov ◽  
Boris V. Smorodsky
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Leading Edge ◽  
Supersonic Boundary Layer ◽  
Mean Flow ◽  
Swept Wing ◽  
Wing Model ◽  
Dimensional Boundary ◽  
The Stability ◽  
Good Agreement

Theoretical and an experimental research results of the disturbances development in a swept wing boundary layer are presented at Mach number М = 2. In experiments development of natural and small amplitude controllable disturbances downstream was studied. Experiments were carried out on a swept wing model with a lenticular profile at a zero attack angle. The swept angle of a leading edge was 40°. Wave parameters of moving disturbances were determined. In frames of the linear theory and an approach of the local self-similar mean flow the stability of a compressible three-dimensional boundary layer is studied. Good agreement of the theory with experimental results for transversal scales of unstable vertices of the secondary flow was obtained. However the calculated amplification rates differ from measured values considerably. This disagreement is explained by the nonlinear processes observed in experiment

Prediction of Steady Propeller Performance with a Nonlinear Slipstream and Boundary-Layer Effect

1995 ◽  
Vol 39 (04) ◽  
pp. 297-312
Author(s):  
You-Hua Liu
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Leading Edge ◽  
Viscous Drag ◽  
Viscous Effects ◽  
Lattice Method ◽  
Suction Force ◽  
Layer Effect ◽  
Dimensional Boundary ◽  
Propeller Performance

Both slipstream deformation and viscous effects are factors that affect the performance of a rotating marine propeller but neither of them has been properly treated in most of the current lifting-surface methods and surface panel theories. With the introduction of a partial roll-up wake model that is flexible to various cases of propeller geometry and loading condition, this paper presents a vortex-lattice method that can improve propeller performance prediction especially at heavy loading conditions. Some observations on the calculation of the blade leading-edge suction force and how to deduct it to account for the viscous drag increasing are given. The scale effect of propeller performance can be readily predicted by the quasi-three-dimensional boundary-layer calculation presented in this paper. Some patterns of the limiting streamlines on blade surfaces are also illustrated and compared with experimental results.

Leading-edge receptivity of a hypersonic boundary layer on a flat plate

2001 ◽  
Vol 426 ◽  
pp. 73-94 ◽  
Author(s):  
A. A. MASLOV ◽  
A. N. SHIPLYUK ◽  
A. A. SIDORENKO ◽  
D. ARNAL
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Inclination Angles ◽  
Tollmien Schlichting ◽  
Radiation Conditions

Experimental investigations of the boundary layer receptivity, on the sharp leading edge of a at plate, to acoustic waves induced by two-dimensional and three- dimensional perturbers, have been performed for a free-stream Mach number M∞ = 5.92. The fields of controlled free-stream disturbances were studied. It was shown that two-dimensional and three-dimensional perturbers radiate acoustic waves and that these perturbers present a set of harmonic motionless sources and moving sources with constant amplitude. The disturbances excited in the boundary layer were measured. It was found that acoustic waves impinging on the leading edge generate Tollmien–Schlichting waves in the boundary layer. The receptivity coefficients were obtained for several radiation conditions and intensities. It was shown that there is a dependence of receptivity coefficients on the wave inclination angles.

Mechanisms and passive control of crossflow-vortex-induced transition in a three-dimensional boundary layer

2002 ◽  
Vol 456 ◽  
pp. 49-84 ◽  
Author(s):  
PETER WASSERMANN ◽  
MARKUS KLOKER
Keyword(s):  
Boundary Layer ◽  
Passive Control ◽  
Three Dimensional ◽  
Plate Boundary ◽  
Secondary Instability ◽  
Base Flow ◽  
Transition Control ◽  
Dimensional Boundary ◽  
Layer Flow ◽  
Underlying Mechanisms

Crossflow-vortex-induced laminar breakdown in a three-dimensional flat-plate boundary-layer flow is investigated in detail by means of spatial direct numerical simulations. The base flow is generic for an infinite swept wing, with decreasing favourable chordwise pressure gradient. First, the downstream growth and nonlinear saturation states initiated by a crossflow-vortex-mode packet as well as by single crossflow-vortex modes with various spanwise wavenumbers are simulated. Second, the secondary instability of the flow induced by the saturated crossflow vortices is scrutinized, clearly indicating the convective nature of the secondary instability and strengthening knowledge of the conditions for its onset. Emphasis is on the effect of crossflow-vortex-mode packets and of the spanwise vortex spacing on the secondary stability properties of the saturation states. Saturated uniform crossflow vortices initiated by single crossflow-vortex modes turn out to be less unstable than vortices initiated by a packet of vortex modes, and closely spaced saturated vortices are even stable. Third, we investigate the transition control strategy of upstream flow deformation by appropriate steady nonlinear vortex modes as applied in wind tunnel experiments at the Arizona State University. A significant transition delay is shown in the base flow considered here, and the underlying mechanisms are specified.

Receptivity to free-stream vorticity of flow past a flat plate with elliptic leading edge

2010 ◽  
Vol 653 ◽  
pp. 245-271 ◽  
Author(s):  
L.-U. SCHRADER ◽  
L. BRANDT ◽  
C. MAVRIPLIS ◽  
D. S. HENNINGSON
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Free Stream ◽  
Three Dimensional ◽  
Low Frequency ◽  
Leading Edge ◽  
Sound Waves ◽  
Streamwise Vorticity ◽  
Low Frequencies ◽  
Free Stream Turbulence

Receptivity of the two-dimensional boundary layer on a flat plate with elliptic leading edge is studied by numerical simulation. Vortical perturbations in the oncoming free stream are considered, impinging on two leading edges with different aspect ratio to identify the effect of bluntness. The relevance of the three vorticity components of natural free-stream turbulence is illuminated by considering axial, vertical and spanwise vorticity separately at different angular frequencies. The boundary layer is most receptive to zero-frequency axial vorticity, triggering a streaky pattern of alternating positive and negative streamwise disturbance velocity. This is in line with earlier numerical studies on non-modal growth of elongated structures in the Blasius boundary layer. We find that the effect of leading-edge bluntness is insignificant for axial free-stream vortices alone. On the other hand, vertical free-stream vorticity is also able to excite non-modal instability in particular at zero and low frequencies. This mechanism relies on the generation of streamwise vorticity through stretching and tilting of the vertical vortex columns at the leading edge and is significantly stronger when the leading edge is blunt. It can thus be concluded that the non-modal boundary-layer response to a free-stream turbulence field with three-dimensional vorticity is enhanced in the presence of a blunt leading edge. At high frequencies of the disturbances the boundary layer becomes receptive to spanwise free-stream vorticity, triggering Tollmien–Schlichting (T-S) modes and receptivity increases with leading-edge bluntness. The receptivity coefficients to free-stream vortices are found to be about 15% of those to sound waves reported in the literature. For the boundary layers and free-stream perturbations considered, the amplitude of the T-S waves remains small compared with the low-frequency streak amplitudes.

The three-dimensional laminar boundary layer on a flat plate

1965 ◽  
Vol 22 (3) ◽  
pp. 587-598 ◽  
Author(s):  
L. Sowerby
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Three Dimensional ◽  
Leading Edge ◽  
Main Stream ◽  
Dimensional Parameter ◽  
Stress Components ◽  
Dimensional Boundary ◽  
Layer Flow ◽  
Limiting Streamlines

A series expansion is derived for the three-dimensional boundary-layer flow over a flat plate, arising from a general main-stream flow over the plate. The series involved are calculated as far as terms of order ξ2, where ξ is a non-dimensional parameter defining distance measured from the leading edge of the plate. The results are applied to an example in which the main stream arises from the disturbance of a uniform stream by a circular cylinder mounted downstream from the leading edge of the plate, the axis of the cylinder being normal to the plate. Calculations are made for shear stress components on the plate, and for the deviation of direction of the limiting streamlines from those in the main stream.

Reynolds stress development in pressure-driven three-dimensional turbulent boundary layers

1989 ◽  
Vol 202 ◽  
pp. 263-294 ◽  
Author(s):  
Shawn D. Anderson ◽  
John K. Eaton
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Reynolds Stress ◽  
Free Stream ◽  
Three Dimensional ◽  
Radius Of Curvature ◽  
Two Dimensional ◽  
Stress Vector ◽  
Dimensional Boundary ◽  
Cross Wire

The development of the Reynolds stress field was studied for flows in which an initially two-dimensional boundary layer was skewed sideways by a spanwise pressure gradient ahead of an upstream-facing wedge. Two different wedges were used, providing a variation in the boundary-layer skewing. Measurements of all components of the Reynolds stress tensor and all ten triple products were measured using a rotatable cross-wire anemometer. The results show the expected lag of the shear stress vector behind the strain rate. Comparison of the two present experiments with previous data suggests that the lag can be estimated if the radius of curvature of the free-stream streamline is known. The magnitude of the shear stress vector in the plane of the wall is seen to decrease rapidly as the boundary-layer skewing increases. The amount of decrease is apparently related to the skewing angle between the wall and the free stream. The triple products evolve rapidly and profiles in the three-dimensional boundary layer are considerably different than two-dimensional profiles, leaving little hope for gradient transport models for the Reynolds stresses. The simplified model presented by Rotta (1979) performs reasonably well providing that an appropriate value of the T-parameter is chosen.

Sign in / Sign up

Export Citation Format

Share Document