scholarly journals The effect of Y on the microstructure and mechanical performance of an Mg-Al-Y casting alloy

2021 ◽  
Vol 2 ◽  
Author(s):  
K. Korgiopoulos ◽  
M. Pekguleryuz
Keyword(s):  
Mechanical Performance ◽  
Tensile Ductility ◽  
Close Association ◽  
X Rays ◽  
Structural Components ◽  
Electric Cars ◽  
Automotive Body ◽  
Β Phase ◽  
Compression Strain ◽  
The Matrix

Abstract Environmental gains of electric cars can be optimized with the use of lightweight and recyclable magnesium in the vehicle’s structural components. Ductility improvement of low-density Mg-Al alloys will extend their use in automotive body applications. The authors achieved 63% ductility improvement in Mg-6wt%Al with trace Y (1.5 ppm) due to the β-phase refinement and predicted that higher levels would not perform as well. As predicted, 0.3wt% of Y addition investigated in this study led to lower mechanical performance and β-phase refinement than those obtained with trace additions. The tensile ductility and yield strength increased by ~13% and 16%, respectively, and the compression strain to fracture by ~22%. Scanning electron and optical microscopy, X-Rays diffraction, mechanical testing and thermodynamic calculations were used to investigate the effect of 0.3wt% Y on the microstructure of Mg-6wt%Al. The matrix dissolution revealed the close association of the Al2Y and the β-Mg17Al12 phases.

Improving x-ray map resolution with image restoration techniques

1996 ◽  
Vol 54 ◽  
pp. 598-599
Author(s):  
Richard B. Mott ◽  
John J. Friel ◽  
Charles G. Waldman
Keyword(s):  
Image Restoration ◽  
Hubble Space Telescope ◽  
Extensive Literature ◽  
Small Object ◽  
X Rays ◽  
X Ray ◽  
Mapping Parameters ◽  
The Matrix ◽  
The 1960S ◽  
Map Resolution

X-rays are emitted from a relatively large volume in bulk samples, limiting the smallest features which are visible in X-ray maps. Beam spreading also hampers attempts to make geometric measurements of features based on their boundaries in X-ray maps. This has prompted recent interest in using low voltages, and consequently mapping L or M lines, in order to minimize the blurring of the maps.An alternative strategy draws on the extensive work in image restoration (deblurring) developed in space science and astronomy since the 1960s. A recent example is the restoration of images from the Hubble Space Telescope prior to its new optics. Extensive literature exists on the theory of image restoration. The simplest case and its correspondence with X-ray mapping parameters is shown in Figures 1 and 2.Using pixels much smaller than the X-ray volume, a small object of differing composition from the matrix generates a broad, low response. This shape corresponds to the point spread function (PSF). The observed X-ray map can be modeled as an “ideal” map, with an X-ray volume of zero, convolved with the PSF. Figure 2a shows the 1-dimensional case of a line profile across a thin layer. Figure 2b shows an idealized noise-free profile which is then convolved with the PSF to give the blurred profile of Figure 2c.

scholarly journals Preparation of Long Sisal Fiber-Reinforced Polylactic Acid Biocomposites with Highly Improved Mechanical Performance

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1124
Author(s):  
Zhifang Liang ◽  
Hongwu Wu ◽  
Ruipu Liu ◽  
Caiquan Wu
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Performance ◽  
Tensile Elongation ◽  
Sisal Fiber ◽  
Fiber Reinforced ◽  
Impact Performance ◽  
The Matrix ◽  
Blending Process ◽  
Extension Direction

Green biodegradable plastics have come into focus as an alternative to restricted plastic products. In this paper, continuous long sisal fiber (SF)/polylactic acid (PLA) premixes were prepared by an extrusion-rolling blending process, and then unidirectional continuous long sisal fiber-reinforced PLA composites (LSFCs) were prepared by compression molding to explore the effect of long fiber on the mechanical properties of sisal fiber-reinforced composites. As a comparison, random short sisal fiber-reinforced PLA composites (SSFCs) were prepared by open milling and molding. The experimental results show that continuous long sisal fiber/PLA premixes could be successfully obtained from this pre-blending process. It was found that the presence of long sisal fibers could greatly improve the tensile strength of LSFC material along the fiber extension direction and slightly increase its tensile elongation. Continuous long fibers in LSFCs could greatly participate in supporting the load applied to the composite material. However, when comparing the mechanical properties of the two composite materials, the poor compatibility between the fiber and the matrix made fiber’s reinforcement effect not well reflected in SSFCs. Similarly, the flexural performance and impact performance of LSFCs had been improved considerably versus SSFCs.

scholarly journals Is Micro X-ray Computer Tomography a Suitable Non-Destructive Method for the Characterisation of Dental Materials?

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1271
Author(s):  
Andreas Koenig ◽  
Leonie Schmohl ◽  
Johannes Scheffler ◽  
Florian Fuchs ◽  
Michaela Schulz-Siegmund ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Computer Tomography ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Three Dimensional ◽  
X Rays ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multiple Measurements ◽  
High Doses

The aim of the study was to investigate the effect of X-rays used in micro X-ray computer tomography (µXCT) on the mechanical performance and microstructure of a variety of dental materials. Standardised bending beams (2 × 2 × 25 mm3) were forwarded to irradiation with an industrial tomograph. Using three-dimensional datasets, the porosity of the materials was quantified and flexural strength was investigated prior to and after irradiation. The thermal properties of irradiated and unirradiated materials were analysed and compared by means of differential scanning calorimetry (DSC). Single µXCT measurements led to a significant decrease in flexural strength of polycarbonate with acrylnitril-butadien-styrol (PC-ABS). No significant influence in flexural strength was identified for resin-based composites (RBCs), poly(methyl methacrylate) (PMMA), and zinc phosphate cement (HAR) after a single irradiation by measurement. However, DSC results suggest that changes in the microstructure of PMMA are possible with increasing radiation doses (multiple measurements, longer measurements, higher output power from the X-ray tube). In summary, it must be assumed that X-ray radiation during µXCT measurement at high doses can lead to changes in the structure and properties of certain polymers.

scholarly journals Influence of electrode tip diameter on metallurgical and mechanical aspects of spot welded duplex stainless steel

2020 ◽  
Vol 39 (1) ◽  
pp. 317-327
Author(s):  
Vivek D. Kalyankar ◽  
Gautam P. Chudasama
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Mechanical Performance ◽  
Welding Current ◽  
Thick Sheet ◽  
Automotive Body ◽  
Nugget Diameter ◽  
Feasible Range ◽  
Research Outcome ◽  
Spot Welded

AbstractIn this article, the influence of electrode tip diameter is investigated for spot welded duplex stainless steel (DSS). Electrode tip diameter and welding current are considered as the major influencing parameters and their values are varied within the feasible range, suitable for 0.8 mm thick sheet, whereas other important parameters such as welding time and electrode force are kept constant. DSS with the chosen thickness range is now becoming a useful material in automotive body-in-white applications and in future it will become one of the key materials replacing the existing materials and hence research outcome of the present work may be beneficial from application view point. In this work, the spot welding quality is inspected through metallurgical aspects (microstructure and microhardness), physical aspects (nugget diameter and electrode indentation), mechanical performance (tensile shear strength [TSS]) and failure mode. The obtained result shows that smaller electrode tip diameter limits nugget diameter due to expulsion phenomena and increases electrode indentation due to higher current intensity. TSS decreases with increase in electrode tip diameter for the same welding current but maximum TSS obtained for particular electrode tip diameter increases with increase in electrode tip diameter up to a specific limit and then it remains constant.

scholarly journals Nanocomposites Materials of PLA Reinforced with Nanoclays Using a Masterbatch Technology: A Study of the Mechanical Performance and Its Sustainability

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2133
Author(s):  
Helena Oliver-Ortega ◽  
Josep Tresserras ◽  
Fernando Julian ◽  
Manel Alcalà ◽  
Alba Bala ◽  
...  
Keyword(s):  
Food Packaging ◽  
Mechanical Performance ◽  
Polymeric Materials ◽  
Barrier Properties ◽  
Food Tray ◽  
Environmental Concerns ◽  
Poly Lactic Acid ◽  
The Matrix ◽  
Surface Modified ◽  
Being Moved

Packaging consumes around 40% of the total plastic production. One of the most important fields with high requirements is food packaging. Food packaging products have been commonly produced with petrol polymers, but due to environmental concerns, the market is being moved to biopolymers. Poly (lactic acid) (PLA) is the most promising biopolymer, as it is bio-based and biodegradable, and it is well established in the market. Nonetheless, its barrier properties need to be enhanced to be competitive with other polymers such as polyethylene terephthalate (PET). Nanoclays improve the barrier properties of polymeric materials if correct dispersion and exfoliation are obtained. Thus, it marks a milestone to obtain an appropriate dispersion. A predispersed methodology is proposed as a compounding process to improve the dispersion of these composites instead of common melt procedures. Afterwards, the effect of the polarity of the matrix was analyzing using polar and surface modified nanoclays with contents ranging from 2 to 8% w/w. The results showed the suitability of the predispersed and concentrated compound, technically named masterbatch, to obtain intercalated structures and the higher dispersion of polar nanoclays. Finally, the mechanical performance and sustainability of the prepared materials were simulated in a food tray, showing the best assessment of these materials and their lower fingerprint.

Properties of a Dielectric Elastomer Actuator Modified by Dispersion of Functionalised Carbon Nanotubes

2012 ◽  
Vol 79 ◽  
pp. 41-46 ◽  
Author(s):  
Fabia Galantini ◽  
Sabrina Bianchi ◽  
Valter Castelvetro ◽  
Irene Anguillesi ◽  
Giuseppe Gallone
Keyword(s):  
Carbon Nanotubes ◽  
Dielectric Constant ◽  
Mechanical Performance ◽  
Broad Class ◽  
Dielectric Elastomer ◽  
Low Dielectric ◽  
Dielectric Elastomer Actuators ◽  
Electromechanical Transduction ◽  
The Matrix ◽  
Simple Matrix

Among the broad class of electro-active polymers, dielectric elastomer actuators represent a rapidly growing technology for electromechanical transduction. In order to further develop this applied science, the high driving voltages currently needed must be reduced. For this purpose, one of the most promising and adopted approach is to increase the dielectric constant while maintaining both low dielectric losses and high mechanical compliance. In this work, a dielectric elastomer was prepared by dispersing functionalised carbon nanotubes into a polyurethane matrix and the effects of filler dispersion into the matrix were studied in terms of dielectric, mechanical and electro-mechanical performance. An interesting increment of the dielectric constant was observed throughout the collected spectrum while the loss factor remained almost unchanged with respect to the simple matrix, indicating that conductive percolation paths did not arise in such a system. Consequences of the chemical functionalisation of carbon nanotubes with respect to the use of unmodified filler were also studied and discussed along with rising benefits and drawbacks for the whole composite material.

scholarly journals Utilization of vegetable fibers for production of reinforced cementitious materials

2018 ◽  
Vol 2 ◽  
pp. 145-154 ◽  
Author(s):  
Viviane Costa Correia ◽  
Sergio Francisco Santos ◽  
Holmer Savastano Jr ◽  
Vanderley Moacyr John
Keyword(s):  
Mechanical Performance ◽  
Stress Transfer ◽  
Cost Effective ◽  
Nanofibrillated Cellulose ◽  
Cementitious Materials ◽  
Vegetable Fibers ◽  
The Matrix ◽  
As Stress ◽  
Hybrid Reinforcement ◽  
Cellulosic Pulp

Vegetable fibers produced from agroindustrial resources in the macro, micro and nanometric scales have been used as reinforcement in cementitious materials. The cellulosic pulp, besides being used as the reinforcing element, is also the processing fiber that is responsible for the filtration system in the Hatcheck method. On the other hand, the nanofibrillated cellulose has the advantage of having good mechanical performance and high specific surface, which contributes to improve the adhesion between fiber and matrix. In the hybrid reinforcement, with micro and nanofibers, the cellulose performs bonding elements with the matrix and acts as stress transfer bridges in the micro and nano-cracking network with the corresponding strengthening and toughening of the cementitious composite. Some strategies are studied to mitigate the degradation of the vegetable fibers used in cost-effective and non-conventional fiber cement, as well as to reach a sustainable fiber cement production. As a practical example, the accelerated carbonation curing at early age is a developing technology to increase the durability of composite materials: it decreases porosity, promotes a higher density in the interface generating a good fiber–matrix adhesion and a better mechanical behavior. Thus, the vegetable fibers are potentially applicable to produce high mechanical performance and sustainable cementitious materials for use in the Civil Construction.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

The Influence of Mobile Dislocation Density on the Fracture Toughness of B2-Based Ni-Fe-Al Alloys

1994 ◽  
Vol 350 ◽  
Author(s):  
A. Misra ◽  
R. D. Noebe ◽  
R. Gibala
Keyword(s):  
Fracture Toughness ◽  
Dislocation Density ◽  
Tensile Ductility ◽  
Growth Direction ◽  
Mobile Dislocation ◽  
Second Phase ◽  
Mobile Dislocation Density ◽  
Dislocation Generation ◽  
Multiphase Materials ◽  
Β Phase

AbstractThe deformation and fracture behaviors of two directionally solidified multi-phase Ni-Fe-Al ordered alloys were investigated. One alloy consisted of continuous β+γ lamellae with fine γ precipitates within the γ phase. The NiAl-based β phase of this alloy exhibited <100> slip even when deformed parallel to the [001] growth direction. This material exhibited an initiation fracture toughness of ∼ 30 MPa √m and tensile ductility of 10%. The second alloy consisted of aligned but discontinuous γ lamellae within a continuous β phase. Again, the γ phase contained γ precipitates, but unlike the previous alloy, the β phase also contained a fine dispersion of bcc precipitates due to spinodal decomposition. The β phase of this alloy deformed by <111> slip. This four-phase alloy exhibited a fracture toughness of ∼ 21 MPa √m and tensile ductility of 2%. Observations of the plastic zone in both alloys indicated significant plasticity in the β phase due to easy slip transfer from the ductile second phase. The enhanced fracture resistance of these multiphase materials compared to single phase β alloys is attributed in large part to intrinsic toughening of the β phase by an increased mobile dislocation density due to efficient dislocation generation from the β/γ interfaces.

Sign in / Sign up

Export Citation Format

Share Document