The adverse cyclic and collective pitch effect in a rotor

2019 ◽  
Vol 123 (1264) ◽  
pp. 805-827 ◽  
Author(s):  
Hak Yoon Kim
Keyword(s):  
Simulation Method ◽  
Navier Stokes ◽  
Equilibrium Conditions ◽  
High Lift ◽  
Helicopter Control ◽  
Shaft Angle ◽  
Simulation Results ◽  
Advance Ratio ◽  
Drag Ratio ◽  
Lift To Drag Ratio

AbstractNumerical simulations have been carried out for a 32.16-ft-diameter rotor in autorotational forward flight. Coupled flapping and rotational equations were solved using the transient simulation method (TSM) to ascertain the quasistatic torque equilibrium conditions. The Pitt/Peters inflow theory was adopted in the simulations, and an airfoil look-up table made by a compressible Navier-Stokes solver was used. The adverse cyclic and collective pitch inputs were introduced in a similar fashion to helicopter control in that the cyclic lever is pulled back and the collective lever is pushed down for increasing airspeeds. The simulation results showed that the longitudinal cyclic pitch input combined with a lowered collective pitch increases the rotating torque for a low shaft angle and an advance ratio greater than one, producing both high lift and a high lift-to-drag ratio. Upon introducing the adverse cyclic and collective pitch inputs, the control range broadened, and a torque equilibrium condition was detected at 414.7kt (700ft/s) of airspeed in the simulation.

Effects of Aspect Ratio on the Hydrodynamic Performance of Circular Cambered Otter Board

2018 ◽  
Author(s):  
Liuyi Huang ◽  
Yuyan Li ◽  
Jiqiang Xu ◽  
Qingchang Xu ◽  
Fenfang Zhao ◽  
...  
Keyword(s):  
Lift Coefficient ◽  
Flow Distribution ◽  
Full Scale ◽  
Hydrodynamic Performance ◽  
High Lift ◽  
Aspect Ratios ◽  
Simulation Results ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Good Agreement

An otter board is an important device that provides a desired horizontal opening of a trawl net. A high lift coefficient or lift-to-drag ratio is required for an otter board to maintain fishing efficiency. In the present work, the hydrodynamic performance of a circular cambered otter board was studied by numerical simulation, including the effects of aspect ratios (AR), and flow distribution around the otter board. Model tests were conducted in the flume tank as well as a comparison to the numerical results. It showed that simulation results exhibited very good agreement with experiment results. Results demonstrated that the model otter board had a critical angle of attack (AOA) of 50° (when the stall appeared). The maximum lift coefficient and lift-to-drag ratio of the model otter board were 2.421 and 3.719, respectively. However, the maximum values of the full-scale otter board increased first and then decreased with an increasing AR. And the full-scale otter board had a better performance when AR = 2.489, it can enhance the lift coefficient by 17.4% compared with the initial otter board (AR = 1.25). In addition, the flow distribution around the otter board showed that the flow was smooth at small AOAs, when it attacked at large AOA (exceeded 55°), flow separation and eddies were appeared at the lee-side of the otter board.

An Investigation of Drag Reduction on Gurney Flaps by an Three-Element Airfoil

2011 ◽  
Vol 138-139 ◽  
pp. 229-233
Author(s):  
Pei Qing Liu ◽  
Shuo Yang ◽  
Yun Tian
Keyword(s):  
Drag Coefficient ◽  
Aerodynamic Characteristic ◽  
Lift Force ◽  
Lift Coefficient ◽  
Simulation Method ◽  
High Lift ◽  
Gurney Flap ◽  
Different Types ◽  
Drag Ratio ◽  
Lift To Drag Ratio

During airplane’s take-off, higher lift force should be provided by wing used high lift devices, and the drag should be lower. The design basis of high lift devices with good aerodynamic characteristic is the design of the multi-element airfoil. When a multi-element airfoil is used Gurney flap, lift coefficient can be improved while drag coefficient is also increased, but the lift-to-drag ratio is reduced. In this paper, the numerical simulation method is used to study the aerodynamic characteristic of the multi-element airfoil used Gurney flap with slat in the configuration of take-off. Lift coefficient and drag coefficient of the multi-element airfoil with Gurney flap can be reduced by slat while lift-to-drag ratio of airfoil is increased. Through the comparisons of the multi-element airfoils with Gurney flap with different types of slats, the optimized multi-element airfoil with higher lift coefficient and lower drag coefficient is obtained ultimately.

Comparison between Methods of Generation of Waveriders Derived from Streamline Tracing and Simplified Method

2013 ◽  
Vol 390 ◽  
pp. 134-140
Author(s):  
Feng Ding ◽  
Jun Liu ◽  
Liang Jin ◽  
Shi Bin Luo
Keyword(s):  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
High Lift ◽  
Shape Factors ◽  
Simplified Method ◽  
Streamline Tracing ◽  
Simulation Results ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Tracing Method

Waverider with a high lift-to-drag ratio has drawn an ever increasing attention. Usually, waverider is obtained by tracing streamline. A simplified generation method of waverider is introduced in the present paper named geometric relations method. Three groups of cone-derived waverider configuration, respectively, based on the geometric relations method and the streamline tracing method are generated for the comparisons of the shape factors, inviscid aerodynamic characteristics, and flow field structures by investigating the numerical simulation results. The results show that the effect of the Mach number and the shock angle on the differences caused by the two methods are not significantly different. While the volumetric efficiency of the waverider configuration based on the geometric relations method is larger than those based on the streamline tracing, the inviscid lift-to-drag ratio of the former is less than the latter. Although the geometric relations method is much easier than the streamline tracing method, the simplified method reduces the aerodynamic performance of the waverider configuration.

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

Optimal Design of Wind Turbines Using BIAS, A Method of Multipliers Code

1988 ◽  
Author(s):  
B. D. Vick ◽  
W. Wrigglesworth ◽  
L. B. Scott ◽  
K. M. Ragsdell
Keyword(s):  
Optimal Design ◽  
Rough Surface ◽  
Wind Turbines ◽  
Lift Coefficient ◽  
Power Coefficient ◽  
Method Of Multipliers ◽  
High Lift ◽  
Small Wind Turbines ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract A method has been developed and is demonstrated which determines the chord and twist distribution for a wind turbine with maximum power coefficient. Only small wind turbines (less than 10 kilowatts) are considered in this study, but the method could be used for larger wind turbines. Glauert determined a method for estimating the chord and twist distribution that will maximize the power coefficient if there is no drag. However, the method proposed here determines the chord and twist distribution which will maximize the power coefficient with the effect of drag included. Including drag in the analysis does not significantly affect the Glauert chord and twist distribution for airfoils with a high lift coefficient at the maximum lift to drag ratio. However, if the airfoil has a fairly low lift coefficient at its maximum lift to drag ratio due to its shape or a rough surface then significant improvement can be obtained in power coefficient by altering the Glauert chord and twist distribution according to the method proposed herein.

Roughness Sensitivity Considerations for Thick Rotor Blade Airfoils

2003 ◽  
Vol 125 (4) ◽  
pp. 468-478 ◽  
Author(s):  
R. P. J. O. M. van Rooij ◽  
W. A. Timmer
Keyword(s):  
Turbine Blades ◽  
Leading Edge ◽  
Lower Surface ◽  
Vortex Generators ◽  
Wind Turbine Blades ◽  
High Lift ◽  
Edge Roughness ◽  
Proper Design ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In modern wind turbine blades, airfoils of more than 25% thickness can be found at mid-span and inboard locations. At mid-span, aerodynamic requirements dominate, demanding a high lift-to-drag ratio, moderate to high lift and low roughness sensitivity. Towards the root, structural requirements become more important. In this paper, the performance for the airfoil series DU FFA, S8xx, AH, Risø and NACA are reviewed. For the 25% and 30% thick airfoils, the best performing airfoils can be recognized by a restricted upper-surface thickness and an S-shaped lower surface for aft-loading. Differences in performance of the DU 91-W2-250 (25%), S814 (24%) and Risø-A1-24 (24%) airfoils are small. For a 30% thickness, the DU 97-W-300 meets the requirements best. Reduction of roughness sensitivity can be achieved both by proper design and by application of vortex generators on the upper surface of the airfoil. Maximum lift and lift-to-drag ratio are, in general, enhanced for the rough configuration when vortex generators are used. At inboard locations, 2-D wind tunnel tests do not represent the performance characteristics well because the influence of rotation is not included. The RFOIL code is believed to be capable of approximating the rotational effect. Results from this code indicate that rotational effects dramatically reduce roughness sensitivity effects at inboard locations. In particular, the change in lift characteristics in the case of leading edge roughness for the 35% and 40% thick DU airfoils, DU 00-W-350 and DU 00-W-401, respectively, is remarkable. As a result of the strong reduction of roughness sensitivity, the design for inboard airfoils can primarily focus on high lift and structural demands.

420 Aerodynamic Characteristics and Flow Field of High Lift-to-drag Ratio Airfoils in Low Reynolds Number

2015 ◽  
Vol 2015.68 (0) ◽  
pp. 167-168 ◽  
Author(s):  
Takahiro MAKIZONO ◽  
Gaku SASAKI ◽  
Hiroshi OCHI ◽  
Takaaki MATSUMOTO ◽  
Koichi YONEMOTO
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Low Reynolds Number ◽  
Aerodynamic Characteristics ◽  
High Lift ◽  
Low Reynolds ◽  
Drag Ratio ◽  
Lift To Drag Ratio
Sign in / Sign up

Export Citation Format

Share Document