Aspect ratio effect on elliptical sonic jet mixing

2016 ◽  
Vol 120 (1230) ◽  
pp. 1197-1214 ◽  
Author(s):  
V. Chauhan ◽  
S.M. Aravindh Kumar ◽  
E. Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Mach Disk ◽  
Jet Mixing ◽  
Disk Formation ◽  
Aspect Ratios ◽  
Sonic Jet ◽  
Nozzle Pressure ◽  
Expansion Level ◽  
Elliptical Jet ◽  
Different Levels

ABSTRACTThe effects of aspect ratio on elliptical sonic jet decay at different levels of under-expansion has been studied experimentally. Elliptical sonic jets from orifices of same area with aspect ratios (AR) 2, 4 and 6 at nozzle pressure ratios 2 to 5 in steps of 1 have also been studied. A circular jet from an orifice with an area equal to that of elliptical orifice was also studied for comparison. Jet centreline pressure decay, spread and waves present in the jet core were analysed. The results show that the mixing of the elliptical jet is superior to the circular jet, at all the nozzle pressure ratios of the present study. Also, the aspect ratio of the elliptical orifice has a strong influence on the jet mixing. Elliptical jets of aspect ratio 4 and 6 experience a significantly higher mixing than the aspect ratio 2 jet, till the under-expansion level corresponding to Mach disk formation. For higher under-expansion levels, the mixing of AR 4 and 6 jets become inferior to that of the AR 2 jet.

Nozzle Aspect Ratio Effect on Supersonic Elliptic Jet Mixing

2017 ◽  
Vol 139 (10) ◽  
Author(s):  
S. M. Aravindh Kumar ◽  
E. Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Nozzle Exit ◽  
Pressure Gradients ◽  
Ratio Effect ◽  
Jet Mixing ◽  
Free Jet ◽  
Aspect Ratios ◽  
Nozzle Pressure ◽  
Axis Switching ◽  
The Waves

Nozzle aspect ratio effect on the mixing of Mach 2 elliptic free jet, issuing from convergent–divergent elliptic nozzles of aspect ratios 2, 3, and 4, in the presence of adverse and marginally favorable pressure gradients at the nozzle exit has been studied experimentally. The results show that AR4 jet enjoys better mixing than AR2 and AR3 jets at all nozzle pressure ratios. The AR2 and AR3 jets displayed axis switching, whereas there is no axis switching for AR4 jet. The shadowgraph shows that the waves in AR4 jet are weaker than those in AR2 and AR3 jets.

Elliptic jet control with triangular tab

2016 ◽  
Vol 231 (8) ◽  
pp. 1460-1477 ◽  
Author(s):  
SM Aravindh Kumar ◽  
Ethirajan Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Major Axis ◽  
Minor Axis ◽  
Mixing Enhancement ◽  
Jet Mixing ◽  
Pitot Pressure ◽  
Nozzle Pressure ◽  
Jet Control ◽  
The Waves ◽  
Different Levels

Elliptic jet mixing influenced by triangular tabs is demonstrated in this work. Mixing modification of a Mach 2 jet from a convergent-divergent elliptic nozzle of aspect ratio 2, in the presence of two triangular tabs along the major and minor axis at the nozzle exit, at different levels of nozzle expansion has been studied. The results show that the mixing caused by tabs along the minor axis is impressive compared to the uncontrolled jet at all the pressure ratios. But for tabs along the major axis, mixing enhancement is significant only for nozzle pressure ratios above 5. Tabs along the minor axis cause better mixing than tabs along the major axis. The iso-pitot pressure contours reveal that the tabs along the minor axis enhance the mixing by bifurcating the jet. Shadowgraphs show that the tabs render the waves in the jet weaker. The present study demonstrates the superior mixing promotion caused by triangular tab than rectangular tab, studied by Aravindh Kumar and Rathakrishnan (2015).

scholarly journals Aspect Ratio Driven Relationship between Nozzle Internal Flow and Supersonic Jet Mixing

Aerospace ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 78
Author(s):  
Kalyani Bhide ◽  
Kiran Siddappaji ◽  
Shaaban Abdallah
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Nozzle Exit ◽  
Supersonic Jet ◽  
Internal Flow ◽  
Shear Stresses ◽  
Loss Mechanism ◽  
Potential Core ◽  
Jet Mixing ◽  
Aspect Ratios

This work attempts to connect internal flow to the exit flow and supersonic jet mixing in rectangular nozzles with low to high aspect ratios (AR). A series of low and high aspect ratio rectangular nozzles (design Mach number = 1.5) with sharp throats are numerically investigated using steady state Reynolds-averaged Navier−Stokes (RANS) computational fluid dynamics (CFD) with k-omega shear stress transport (SST) turbulence model. The numerical shadowgraph reveals stronger shocks at low ARs which become weaker with increasing AR due to less flow turning at the throat. Stronger shocks cause more aggressive gradients in the boundary layer resulting in higher wall shear stresses at the throat for low ARs. The boundary layer becomes thick at low ARs creating more aerodynamic blockage. The boundary layer exiting the nozzle transforms into a shear layer and grows thicker in the high AR nozzle with a smaller potential core length. The variation in the boundary layer growth on the minor and major axis is explained and its growth downstream the throat has a significant role in nozzle exit flow characteristics. The loss mechanism throughout the flow is shown as the entropy generated due to viscous dissipation and accounts for supersonic jet mixing. Axis switching phenomenon is also addressed by analyzing the streamwise vorticity fields at various locations downstream from the nozzle exit.

Tab Aspect Ratio Effect on Supersonic Jet Mixing

2015 ◽  
Vol 32 (3) ◽  
Author(s):  
Mrinal Kaushik ◽  
E. Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Pressure Ratio ◽  
Supersonic Jet ◽  
Small Scale ◽  
Jet Mixing ◽  
Core Length ◽  
Nozzle Pressure ◽  
The Waves ◽  
Length Reduction ◽  
Better Than

AbstractThe efficacy of introducing mixing promoting small-scale vortices by two rectangular tabs, of aspect ratio 1.0, 1.5 and 2.0, placed at diametrically opposite locations at the exit of a Mach 1.73 convergent–divergent circular nozzle has been experimentally investigated, for NPRs from 4 to 8, covering overexpanded, correctly expanded and underexpanded states of the jet. The area blockage due to the each tab was 2.5% of the nozzle exit area. Keeping the blockage constant, the aspect ratio (defined as the ratio of length to width of the tab) was varied. A maximum core length reduction of 84.6% was caused by the tabs of aspect ratio 1.0, at underexpanded conditions corresponding to NPR (nozzle pressure ratio) 6. At this NPR, tabs of aspect ratio 1.5 and 2.0 caused core length reduction of 76.9% and 61.5%, respectively. The mixing promoting efficiency of aspect ratio 1.0 is found to be better than 1.5 and 2.0, at all NPRs of the present study, except NPR 5. The shadowgraph pictures of the uncontrolled and controlled jets clearly demonstrate the effectiveness of the tabs in weakening the waves in the jet core.

Mixing Characteristics and Enhancement of Sonic Elliptic Jets from a Twin Elliptic Orifice

2020 ◽  
Vol 12 (2) ◽  
Author(s):  
S. Parameshwari ◽  
Pradeep Kumar ◽  
S. Thanigaiarasu ◽  
E. Rathakrishnan
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
System Design ◽  
Pressure Ratio ◽  
Jet Noise ◽  
Nozzle Pressure Ratio ◽  
Jet Mixing ◽  
Nozzle Pressure ◽  
Mixing Characteristics ◽  
Ir Signature

The knowledge of jet mixing and its enhancement of elliptic jet are important in a propulsion system of aircraft, rocket, and missile’s system design for advancement of combustion via fuel-air mixture increment, lowering the jet noise and reduction of the plume infrared (IR) signature. The jet issuing from a twin elliptic orifice is non-uniform in shape that promotes the faster mixing and it influences by orifice exit conditions, so knowledge of absence of boundary layer and jet mixing characteristics is important. Hence, an experimental work helps to study the jet mixing for a twin elliptic orifice of aspect ratio two at nozzle pressure ratios of one, two, and three. The proximity between the orifices kept as one to 3mm in steps of one. The experimental readings were taken using pitot probe. The results revealed that jet mixing is faster and effective when the proximity between the orifices is closer to each other than the faraway distances at measured nozzle pressure ratios. Difference in orifice jet core exerted a noticeable influence at high proximity levels of nozzle pressure ratio of three and four for elliptic orifice.

Control of Subsonic and Sonic Jets with Limiting Tabs

2017 ◽  
Vol 34 (1) ◽  
Author(s):  
T. Berrueta ◽  
E. Rathakrishnan
Keyword(s):  
Nozzle Exit ◽  
Pressure Ratio ◽  
Nozzle Pressure Ratio ◽  
Jet Mixing ◽  
Downstream Distance ◽  
The Core ◽  
Maximum Reduction ◽  
Sonic Jet ◽  
Nozzle Pressure ◽  
Mach Numbers

AbstractAerodynamic mixing of subsonic and sonic jets with limiting tabs, with and without corrugations, has been studied experimentally. Limiting tab located at the nozzle exit and at a downstream distance of 0.5D has been considered in this study. Mixing caused by the tab at nozzle exit is found to be better that of tab at 0.5D, for both plain and corrugated geometries. Also, both tabs caused better mixing for underexpanded sonic jets than the correctly expanded sonic jet and subsonic jets. At nozzle pressure ratio 3 the plain tab at the nozzle exit reduced the core by about 56 % and the corrugated tab by about 51 %. But when the plain tab is placed at 0.5D the jet mixing is retarded. However, the corrugated tab at 0.5D enhances the mixing, though not up to the level of the same tab at 0D, at all Mach numbers except 0.6. The maximum reduction of core caused by shifted corrugated tab is 14 % for Mach 0.8 jet.

scholarly journals Simulation of Elliptical Liquid Jet Primary Breakup In Supersonic Crossflow

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Yao-zhi Zhou ◽  
Feng Xiao ◽  
Qing-lian Li ◽  
Chen-yang Li
Keyword(s):  
Aspect Ratio ◽  
Penetration Depth ◽  
Horseshoe Vortex ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Breakup Length ◽  
Aspect Ratios ◽  
Primary Breakup ◽  
Elliptical Jet ◽  
Maximum Spreading

The study of elliptical liquid jets in supersonic flow in a Mach 2.0 is performed numerically. The primary breakup process of the elliptical liquid jet is simulated for a Weber number 223, liquid/gas flux momentum 4.0. The aspect ratios of elliptical geometries are set to be 0.25, 0.5, 1, 2, and 5. The results show a remarkable difference in liquid jet disintegration morphology at different aspect ratios. Under supersonic crossflow conditions, the elliptical liquid jet shows more breakup characteristics than the round liquid jet. As the aspect ratio grows, the penetration depth decreases. The elliptical liquid jet with AR=0.25 has the largest penetration depth in all cases. Moreover, the round jet has a maximum spreading angle of 50.2°. The changing trends of the column breakup length both x direction and y direction are similar. The elliptical jet at a lower aspect ratio has a shorter breakup length due to the narrower windward area. The liquid jet has a pair of larger horseshoe vortex structure and a wider wake region at a higher aspect ratio. Two pairs of reversal vortex pairs with obvious characteristics can be observed in all the simulations.

Control of a supersonic elliptical jet

2017 ◽  
Vol 122 (1247) ◽  
pp. 131-147 ◽  
Author(s):  
A. Bajpai ◽  
E. Rathakrishnan
Keyword(s):  
Nozzle Exit ◽  
Major Axis ◽  
Minor Axis ◽  
The Core ◽  
Core Length ◽  
Nozzle Pressure ◽  
Elliptical Jet ◽  
The Waves ◽  
Length Reduction ◽  
Different Levels

ABSTRACTMach 2 jet from a convergent-divergent elliptical nozzle, of aspect ratio 2, has been controlled with limiting flat and arc tabs. The mixing promoting capability of the flat and arc tabs were studied in the presence of different levels of pressure gradient, at the nozzle exit, corresponding to nozzle pressure ratios of 4 to 8, in steps of one. The geometrical blockage of both the tabs is 5% of nozzle exit area. For the flat tab along the minor axis, the waves in the core become weaker and the core length becomes shorter than the uncontrolled jet, at all the NPRs studied. But the flat tab along the major axis promotes mixing only for some NPRs and retards the mixing for the rest of the NPRs studied. At NPR 5, the flat tab along the minor axis causes the largest core length reduction of 86%. For circular arc tab, along the minor axis, the maximum core length reduction is 55% at NPR 6. Arc tab along the major axis protects the core length for the entire range of the nozzle pressure ratios tested and maximum extension in core length is found at NPR 4, which is 40%.

Study on the Effect of Jets Geometry in Liquid Atomization Based on Nonlinear Stability Analysis

2018 ◽  
Author(s):  
Sajad Jafari ◽  
Taravatsadat Nehzati
Keyword(s):  
Aspect Ratio ◽  
Nonlinear Equations ◽  
Stokes Equations ◽  
Linear Equations ◽  
Nonlinear Stability Analysis ◽  
Regular Perturbation ◽  
Aspect Ratios ◽  
Jet Breakup ◽  
Nonlinear Form ◽  
Elliptical Jet

In this paper, nonlinear instability of an elliptical jet is investigated by considering the impacts of orifice geometry variations using regular perturbation method. In the breakup mechanisms, created disturbances on the jet interfaces will grow owing to the nonlinear dynamics of fluid. In this study, a scrutiny of nonlinear cylindrical jet breakup is done initially. Next, Cosserat equations as a low order form of Navies-Stokes equations are solved on the nonlinear form to exert the impacts of orifice deformation on various aspect ratios. These nonlinear equations, Cosserat equations, are linearly solved in the past papers. As a result, the dispersion equation is derived to find the most unstable wavelength as well as the breakup length. Results reveal that the elliptical jet with low aspect ratio is more unstable rather than cylindrical jet with aspect ratio of one. Furthermore, the nonlinear equations can predict the break up length of elliptical jet more accurate than linear equations. The predicted results are shown to be in good agreement with the experimental results.

Exit Geometry Effect on Jet Mixing

2014 ◽  
Vol 598 ◽  
pp. 151-155 ◽  
Author(s):  
Jatin Mitruka ◽  
Pranav Kumar Singh ◽  
E. Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Nozzle Exit ◽  
Azimuthal Asymmetry ◽  
Continuous Variation ◽  
Mixing Process ◽  
Geometry Effect ◽  
Jet Mixing ◽  
Elliptical Shape ◽  
Elliptical Jet ◽  
The Waves

An elliptical nozzle of 3:1 aspect ratio (AR) issuing a Mach 1.5 jet has been used to investigate its mixing promoting efficiency under over-expanded and under-expanded conditions at the nozzle exit. Azimuthal asymmetry of the elliptical shape is interpreted as a benefit to the mixing process, which is significantly enhanced in comparison to an equivalent circular jet under identical conditions. The elliptical jet decays faster than its circular counterpart throughout the jet field. It is found that continuous variation in the size of the mixing promoting vortices shed from the nozzle exit, as a result of its azimuthal asymmetry, is responsible for faster decay of elliptical jet. The visualization of elliptic jet corroborates the fact that the waves prevailing in the elliptical jet are significantly weaker than those in the circular jet.

Sign in / Sign up

Export Citation Format

Share Document