Rheometry of novel shear thickening fluid and its application for improving the impact energy absorption of p-aramid fabric

2020 ◽  
Vol 155 ◽  
pp. 106954
Author(s):  
Aranya Ghosh ◽  
Abhijit Majumdar ◽  
Bhupendra Singh Butola
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Shear Thickening ◽  
Shear Thickening Fluid ◽  
Aramid Fabric ◽  
The Impact

scholarly journals Functionalization of silica particles to tune the impact resistance of shear thickening fluid treated aramid fabrics

RSC Advances ◽  
2017 ◽  
Vol 7 (78) ◽  
pp. 49787-49794 ◽  
Author(s):  
K. Talreja ◽  
I. Chauhan ◽  
A. Ghosh ◽  
A. Majumdar ◽  
B. S. Butola
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Resistance ◽  
Shear Thickening ◽  
Silica Particles ◽  
Modified Silica ◽  
Shear Thickening Fluid ◽  
Aramid Fabrics ◽  
And Control ◽  
The Impact

Kevlar fabrics treated with MTMS modified silica based STF showed better impact energy absorption as compared to APTES modified and control silica based STF treated fabrics, attributed to changes in interactions between fabrics and silica particles.

Preparation of auxetic warp-knitted spacer fabric impregnated with shear thickening fluid for low-velocity impact resistance

2020 ◽  
pp. 152808372092701 ◽  
Author(s):  
Wanli Xu ◽  
Biao Yan ◽  
Dongmei Hu ◽  
Pibo Ma
Keyword(s):  
Shear Rate ◽  
Energy Absorption ◽  
Impact Resistance ◽  
Shear Thickening ◽  
Weight Fraction ◽  
Low Velocity Impact ◽  
Impact Behavior ◽  
Shear Thickening Fluid ◽  
Spacer Fabric ◽  
The Impact

This paper reports the preparation of auxetic warp-knitted spacer fabric impregnated with shear thickening fluid and studied its impact behavior under low-velocity impact loading. The shear thickening fluids have been prepared by mechanically dispersing 12 nm silica particles with weight fraction of 10, 15, 20, and 25% in various carriers (PEG200, PEG400, and PEG600). Rheological results indicate that shear thickening fluid experiences shear thickening transition at a specific shear rate. The critical shear rate reduces, and initial viscosity and maximum viscosity increase with the increase of silica weight fraction. The higher molecular weight of polyethylene glycols can lead to lower critical shear rate. The impact process of composite under impact loading can be divided into three stages. The warp-knitted spacer fabric with different negative Poisson’s ratio has a significant effect on the impact behavior. The warp-knitted spacer fabric with better auxetic performance endows composite better impact resistance, the specific performance is the deformation depth, and energy absorption and peak load increase with the increase of auxetic effect of fabric. The silica weight fraction of shear thickening fluid can increase the energy absorption of composite due to the shear thickening transition of shear thickening fluid. Shear thickening fluid has a synergistic effect with the auxetic warp-knitted spacer fabric on impact resistance of composite. The various carriers have no obvious influence on the overall energy absorption and impact load of composites.

An investigation on composite laminates including shear thickening fluid under stab condition

2018 ◽  
Vol 53 (8) ◽  
pp. 1111-1122 ◽  
Author(s):  
Selim Gürgen
Keyword(s):  
Energy Absorption ◽  
Composite Laminates ◽  
Impact Resistance ◽  
Shear Thickening ◽  
Low Velocity ◽  
Shear Thickening Fluid ◽  
Shear Thickening Fluids ◽  
Absorption Performance ◽  
Thickening Behavior ◽  
The Impact

Shear thickening fluids have been extensively utilized in composite laminate structures to enhance the impact resistance in the last decade. Despite the contribution of shear thickening fluids to the protective systems, the mechanism behind the energy absorption behavior of shear thickening fluids is not fully understood. In the present study, various configurations of composite laminates were prepared and these structures were investigated under low velocity stab conditions. Contrary to the common idea of shear thickening fluid impregnation for fabrics, shear thickening fluids were used in bulk form and by means of this, pure contribution of shear thickening behavior to the energy absorption was investigated. To hold the bulk shear thickening fluids in the composite laminates, Lantor Soric SF honeycomb layers were filled with shear thickening fluids and Twaron fabrics were plied in the structures as the reinforcement. As a result of this study, it is stated that shear thickening behavior is insufficient to effectively improve the energy absorption performance of composite laminates; however, shear thickening fluids are beneficial to fabric based composites because the inter-yarn friction of fabrics is enhanced using shear thickening fluids as an impregnation agent rather than a bulk form.

Effect of SiO2 Nanoparticles on the Mechanical and Low Velocity Impact Properties of Epoxy/Glass Composites

2016 ◽  
Vol 838 ◽  
pp. 29-35
Author(s):  
Michał Landowski ◽  
Krystyna Imielińska
Keyword(s):  
Flexural Strength ◽  
Energy Absorption ◽  
Impact Energy ◽  
Epoxy Matrix ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Nanoparticle Suspension ◽  
Impact Properties ◽  
Velocity Impact ◽  
The Impact

Flexural strength and low velocity impact properties were investigated in terms of possibile improvements due to epoxy matrix modification by SiO2 nanoparticles (1%, 2%, 3%, 5%, 7%wt.) in glass/epoxy laminates formed using hand lay-up method. The matrix resin was Hexion L285 (DGEBA) with Nanopox A410 - SiO2 (20 nm) nanoparticle suspension in the base epoxy resin (DGEBA) supplied by Evonic. Modification of epoxy matrix by variable concentrations of nanoSiO2 does not offer significant improvements in the flexural strength σg, Young’s modulus E and interlaminar shear strength for 1% 3% and 5% nanoSiO2 and for 7% a slight drop (up to ca. 15-20%) was found. Low energy (1J) impact resistance of nanocomposites represented by peak load in dynamic impact characteristics was not changed for nanocompoosites compared to the unmodified material. However at higher impact energy (3J) nanoparticles appear to slightly improve the impact energy absorption for 3% and 5%. The absence or minor improvements in the mechanical behaviour of nanocomposites is due to the failure mechanisms associated with hand layup fabrication technique: (i.e. rapid crack propagation across the extensive resin pockets and numerous pores and voids) which dominate the nanoparticle-dependent crack energy absorption mechanisms (microvoids formation and deformation).

scholarly journals Experimental and numerical analysis of high and low velocity impacts against neat and shear thickening fluid (STF) impregnated weave fabrics

2018 ◽  
Vol 183 ◽  
pp. 01044
Author(s):  
Djalel Eddine Tria ◽  
Larbi Hemmouche ◽  
Abdelhadi Allal ◽  
Abdelkader Benouali
Keyword(s):  
High Velocity ◽  
Shear Thickening ◽  
Force Sensor ◽  
Low Velocity Impact ◽  
Dynamic Force ◽  
Low Velocity ◽  
Shear Thickening Fluid ◽  
Velocity Impact ◽  
Pull Out ◽  
The Impact

This investigation aims to study the efficiency of STF impregnated plain-weave fabric made of Kevlar under high and low velocity impact conditions. The shear thickening fluid (STF) was prepared by ultrasound irradiation of silica nanoparticles (diameter ≈30 nm) dispersed in liquid polyethylene glycol polymer. STF impregnation effect was determined from single yarn pull-out test and penetration at low velocity using drop weight machine equipped with hemi-spherical penetrator and dynamic force sensor. Force-displacement curves of neat and impregnated Kevlar were analysed and compared. Also, the STF impregnation effect on Kevlar multilayers was analysed from high velocity impact tests using 9mm FMJ bullet at 390 m/s. After impact, Back face deformation (BFD) of neat and impregnated Kevlar layers were measured and compared. Results showed that STF impregnated fabrics have better energy absorption and penetration resistance as compared to neat fabrics without affecting the fabric flexibility. When relative yarn translations are restricted (e.g. at very high levels of friction), windowing and yarn pull-out cannot occur, and the fibres engaged with the projectile fail in tension that leads to fabric penetration. Microscopy of these fabrics after testing have shown pitting and damage to the Kevlar filaments caused by the hard silica particles used in the STF. Mesoscopic 3D Finite Element models were developed using explicit LS-DYNA hydrocode to account for STF impregnation by employing the experimental results of yarn pull-out tests, low and high velocity impacts. It was found that friction between fibers and yarns increase the dissipation of energy upon impact by restricting fiber mobility, increasing the energy required for relative yarn translations and transferring the impact energy to a larger number of fibers.

Interplay of fabric structure and shear thickening fluid impregnation in moderating the impact response of high-performance woven fabrics

2020 ◽  
Vol 54 (28) ◽  
pp. 4387-4395
Author(s):  
Sanchi Arora ◽  
Abhijit Majumdar ◽  
Bhupendra Singh Butola
Keyword(s):  
Beneficial Effect ◽  
Energy Absorption ◽  
Impact Energy ◽  
High Performance ◽  
Research Work ◽  
Impact Resistance ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Fabric Structure ◽  
The Impact

The beneficial effect of STF impregnation in enhancing the impact resistance of high-performance fabrics has been extensively reported in the literature. However, this research work reports that fabric structure has a decisive role in moderating the effectiveness of STF impregnation in terms of impact energy absorption. Plain woven fabrics having sett varying from 25 × 25 inch−1 to 55 × 55 inch−1 were impregnated with STF at two different padding pressures to obtain different add-ons. The impact energy absorption by STF impregnated loosely woven fabrics was found to be higher than that of their neat counterparts for both levels of add-on, while opposite trend was observed in case of tightly woven fabrics. Further, comparison of tightly woven plain, 2/2 twill, 3/1 twill and 2 × 2 matt fabrics revealed beneficial effect of STF impregnation, except for the plain woven fabric, establishing that there exists a fabric structure-STF impregnation interplay that tunes the impact resistance of woven fabrics.

Dynamic Energy Absorption Performances of Rain Forest Vehicle (RFV) under Frontal Impact

2014 ◽  
Vol 67 (3) ◽  
Author(s):  
M. S. Othman ◽  
Z. Ahmad
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Loading ◽  
Rain Forest ◽  
Experimental Testing ◽  
Rigid Wall ◽  
Crash Analysis ◽  
Frontal Impact ◽  
Frontal Section ◽  
The Impact

This paper treats the crash analysis and energy absorption response of Rain Forest Vehicle (RFV) subjected to frontal impact scenario namely impacting rigid wall and column. Dynamic computer simulation techniques validated by experimental testing are used to carry out a crash analysis of such vehicle. The study aims at quantifying the energy absorption capability of frontal section of RFV under impact loading, for variations in the load transfer paths and geometry of the crashworthy components. It is evident that the proposed design of the RFV frontal section are desirable as primary impact energy mitigation due to its ability to withstand and absorb impact loads effectively. Furthermore, it is found that the impact energy transmitted to the survival room may feasibly be minimized in these two impact events. The primary outcome of this study is design recommendation for enhancing the level of safety of the off-road vehicle where impact loading is expected.   

Sign in / Sign up

Export Citation Format

Share Document