Reliability analysis of underground excavation in elastic-strain-softening rock mass

2016 ◽  
Vol 60 ◽  
pp. 66-79 ◽  
Author(s):  
Li Song ◽  
Hang-Zhou Li ◽  
Chin Loong Chan ◽  
Bak Kong Low
Keyword(s):  
Rock Mass ◽  
Reliability Analysis ◽  
Elastic Strain ◽  
Strain Softening ◽  
Underground Excavation

Influence exerted by underground excavation shape and by effective stresses on the formation of a tensile strain zone at a depth greater than 1 km

2020 ◽  
pp. 67-75
Author(s):  
Van Min Nguyen ◽  
V. A. Eremenko ◽  
M. A. Sukhorukova ◽  
S. S. Shermatova
Keyword(s):  
Rock Mass ◽  
Cross Sections ◽  
Tensile Strain ◽  
Rock Fracture ◽  
Strain Analysis ◽  
Surrounding Rock ◽  
Underground Excavation ◽  
Secondary Stress ◽  
Principal Stresses ◽  
Mining Depth

The article presents the studies into the secondary stress field formed in surrounding rock mass around underground excavations of different cross-sections and the variants of principal stresses at a mining depth greater than 1 km. The stress-strain analysis of surrounding rock mass around development headings was performed in Map3D environment. The obtained results of the quantitative analysis are currently used in adjustment of the model over the whole period of heading and support of operating mine openings. The estimates of the assumed parameters of excavations, as well as the calculations of micro-strains in surrounding rock mass by three scenarios are given. During heading in the test area in granite, dense fracturing and formation of tensile strain zone proceeds from the boundary of e ≥ 350me and is used to determine rough distances from the roof ( H roof) and sidewalls ( H side) of an underground excavation to the 3 boundary e = 350me (probable rock fracture zone). The modeling has determined the structure of secondary stress and strain fields in the conditions of heading operations at great depths.

scholarly journals Elastoplastic Analysis of Circular Opening Based on a New Strain-Softening Constitutive Model and Its Engineering Application in Hydraulic Fracturing

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
T. Yang ◽  
Q. S. Ye
Keyword(s):  
Rock Mass ◽  
Constitutive Model ◽  
Hydraulic Fracturing ◽  
Bearing Capacity ◽  
Fracture Zone ◽  
Strain Softening ◽  
Circular Opening ◽  
Elastic Peak ◽  
Load Bearing ◽  
Plastic Model

Constitutive effect is extremely important for the research of the mechanical behavior of surrounding rock in hydraulic fracturing engineering. In this paper, based on the triaxial test results, a new elastic-peak plastic-softening-fracture constitutive model (EPSFM) is proposed by considering the plastic bearing behavior of the rock mass. Then, the closed-form solution of a circular opening is deduced with the nonassociated flow rule under the cavity expansion state. Meanwhile, the parameters of the load-bearing coefficient and brittles coefficient are introduced to describe the plastic bearing capacity and strain-softening degrees of rock masses. When the above two parameters take different values, the new solution of EPSFM can be transformed into a series of traditional solutions obtained based on the elastic-perfectly plastic model (EPM), elastic-brittle plastic model (EBM), elastic-strain-softening model (ESM), and elastic-peak plastic-brittle plastic model (EPBM). Therefore, it can be applied to a wider range of rock masses. In addition, the correctness of the solution is validated by comparing with the traditional solutions. The effect of constitutive relation and parameters on the mechanical response of rock mass is also discussed in detail. The research results show that the fracture zone radii of circular opening presents the characteristic of EBM > EPBM > ESM > EPSFM; otherwise, it is on the contrast for the critical hydraulic pressure at the softening-fracture zone interface; the postpeak failure radii show a linear decrease with the increase of load-bearing coefficients or a nonlinear increase with the increasing brittleness coefficient. This study indicates that the rock mass with a certain plastic bearing capacity is more difficult to be cracked by hydraulic fracturing; the higher the strain-softening degree of rock mass is, the easier it is to be cracked. From a practical point of view, it provides very important theoretical values for determining the fracture range of the borehole and providing a design value of the minimum pumping pressure in hydraulic fracturing engineering.

scholarly journals Effect of Joint Density on Rockburst Proneness of the Elastic-Brittle-Plastic Rock Mass

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Jiliang Pan ◽  
Fenhua Ren ◽  
Meifeng Cai
Keyword(s):  
Rock Mass ◽  
Elastic Strain ◽  
Strain Energy ◽  
Elastic Strain Energy ◽  
Jointed Rock ◽  
Jointed Rock Mass ◽  
Joint Density ◽  
Dissipated Energy ◽  
Uniaxial Compression Test ◽  
Plastic Rock

The prediction of rockburst proneness is the basis of preventing and controlling rockburst disasters in rock engineering. Based on energy theory and damage mechanics, the quantitative functional relationship between joint density and energy density was derived. Then, the theoretical results were verified by numerical simulation and uniaxial compression test, and the effect of joint density on rockburst proneness of the elastic-brittle-plastic rock mass was discussed. The results show that the relationship between the joint density and the dissipated energy index of the jointed rock mass is a logarithmic function. With the same total input energy, the higher the joint density, the more the damage dissipation energy. Even in the case of high joint density, the rock mass still has limited resistance to external failure. Under the same joint density, the strength of parallel jointed rock mass is better than that of the cross-jointed rock mass, and the parallel jointed rock mass can accumulate more elastic strain energy and has higher rockburst proneness. The joint density is closely related to the ability of the rock mass to store high strain energy. The higher the joint density is, the weaker the ability to accumulate the elastic strain energy of rock mass is and the lower the rockburst proneness is. It is helpful to predict rockburst proneness by investigating and studying the properties of geological discontinuities. The research results have some theoretical and engineering guiding significance for the prediction of rockburst proneness of the jointed rock mass.

Sign in / Sign up

Export Citation Format

Share Document