Deformed Neogene basins, active faulting and topography in Westland: Distributed crustal mobility west of the Alpine Fault transpressive plate boundary (South Island, New Zealand)

2016 ◽  
Vol 693 ◽  
pp. 340-362 ◽  
Author(s):  
Francesca Ghisetti ◽  
Richard H. Sibson ◽  
Ian Hamling
Keyword(s):  
New Zealand ◽  
Plate Boundary ◽  
Active Faulting ◽  
Alpine Fault

scholarly journals The fluid budget of a continental plate boundary fault: Quantification from the Alpine Fault, New Zealand

2016 ◽  
Vol 445 ◽  
pp. 125-135 ◽  
Author(s):  
Catriona D. Menzies ◽  
Damon A.H. Teagle ◽  
Samuel Niedermann ◽  
Simon C. Cox ◽  
Dave Craw ◽  
...  
Keyword(s):  
New Zealand ◽  
Plate Boundary ◽  
Boundary Fault ◽  
Continental Plate ◽  
Alpine Fault

Highly localized upper mantle deformation during plate boundary initiation near the Alpine fault, New Zealand

Geology ◽  
2021 ◽  
Author(s):  
Steven Kidder ◽  
David J. Prior ◽  
James M. Scott ◽  
Hamid Soleymani ◽  
Yilun Shao
Keyword(s):  
New Zealand ◽  
Upper Mantle ◽  
Plate Boundary ◽  
New Approach ◽  
Fine Grained ◽  
Alpine Fault ◽  
Narrow Width ◽  
Plate Boundary Deformation ◽  
Boundary Deformation ◽  
Total Shear

Peridotite xenoliths entrained in magmas near the Alpine fault (New Zealand) provide the first direct evidence of deformation associated with the propagation of the Australian-Pacific plate boundary through the region at ca. 25–20 Ma. Two of 11 sampled xenolith localities contain fine-grained (40–150 mm) rocks, indicating that deformation in the upper mantle was focused in highly sheared zones. To constrain the nature and conditions of deformation, we combine a flow law with a model linking recrystallized fraction to strain. Temperatures calculated from this new approach (625–970 °C) indicate that the observed deformation occurred at depths of 25–50 km. Calculated shear strains were between 1 and 100, which, given known plate offset rates (10–20 mm/yr) and an estimated interval during which deformation likely occurred (<1.8 m.y.), translate to a total shear zone width in the range 0.2–32 km. This narrow width and the position of mylonite-bearing localities amid mylonite-free sites suggest that early plate boundary deformation was distributed across at least ~60 km but localized in multiple fault strands. Such upper mantle deformation is best described by relatively rigid, plate-like domains separated by rapidly formed, narrow mylonite zones.

Reconciling an Early Nineteenth-Century Rupture of the Alpine Fault at a Section End, Toaroha River, Westland, New Zealand

2020 ◽  
Author(s):  
Robert M. Langridge ◽  
Pilar Villamor ◽  
Jamie D. Howarth ◽  
William F. Ries ◽  
Kate J. Clark ◽  
...  
Keyword(s):  
Nineteenth Century ◽  
New Zealand ◽  
Plate Boundary ◽  
Slip Rate ◽  
Fault System ◽  
Fault Rupture ◽  
Central Section ◽  
Surface Rupture ◽  
Early Nineteenth Century ◽  
Alpine Fault

ABSTRACT The Alpine fault is a high slip-rate plate boundary fault that poses a significant seismic hazard to southern and central New Zealand. To date, the strongest paleoseismic evidence for the onshore southern and central sections indicates that the fault typically ruptures during very large (Mw≥7.7) to great “full-section” earthquakes. Three paleoseismic trenches excavated at the northeastern end of its central section at the Toaroha River (Staples site) provide new insights into its surface-rupture behavior. Paleoseismic ruptures in each trench have been dated using the best-ranked radiocarbon dating fractions, and stratigraphically and temporally correlated between each trench. The preferred timings of the four most recent earthquakes are 1813–1848, 1673–1792, 1250–1580, and ≥1084–1276 C.E. (95% confidence intervals using OxCal 4.4). These surface-rupture dates correlate well with reinterpreted timings of paleoearthquakes from previous trenches excavated nearby and with the timing of shaking-triggered turbidites in lakes along the central section of the Alpine fault. Results from these trenches indicate the most recent rupture event (MRE) in this area postdates the great 1717 C.E. Alpine fault rupture (the most recent full-section rupture of the southern and central sections). This MRE probably occurred within the early nineteenth century and is reconciled as either: (a) a “partial-section” rupture of the central section; (b) a northern section rupture that continued to the southwest; or (c) triggered slip from a Hope-Kelly fault rupture at the southwestern end of the Marlborough fault system (MFS). Although, no single scenario is currently favored, our results indicate that the behavior of the Alpine fault is more complex in the north, as the plate boundary transitions into the MFS. An important outcome is that sites or towns near fault intersections and section ends may experience strong ground motions more frequently due to locally shorter rupture recurrence intervals.

New c. 270 kyr strike-slip and uplift rates for the southern Alpine Fault and implications for the New Zealand plate boundary

2014 ◽  
Vol 64 ◽  
pp. 39-52 ◽  
Author(s):  
N.C. Barth ◽  
D.K. Kulhanek ◽  
A.G. Beu ◽  
C.V. Murray-Wallace ◽  
B.W. Hayward ◽  
...  
Keyword(s):  
New Zealand ◽  
Plate Boundary ◽  
Strike Slip ◽  
Alpine Fault ◽  
Uplift Rates

scholarly journals Lidar reveals uniform Alpine fault offsets and bimodal plate boundary rupture behavior, New Zealand: REPLY

Geology ◽  
2014 ◽  
Vol 42 (10) ◽  
pp. e352-e352
Author(s):  
Gregory P. De Pascale ◽  
Mark C. Quigley ◽  
Tim R. Davies
Keyword(s):  
New Zealand ◽  
Plate Boundary ◽  
Alpine Fault ◽  
Rupture Behavior

scholarly journals Lidar reveals uniform Alpine fault offsets and bimodal plate boundary rupture behavior, New Zealand: COMMENT

Geology ◽  
2014 ◽  
Vol 42 (10) ◽  
pp. e351-e351
Author(s):  
Robert Langridge ◽  
Jamie Howarth ◽  
Ursula Cochran ◽  
Mark Stirling ◽  
Pilar Villamor ◽  
...  
Keyword(s):  
New Zealand ◽  
Plate Boundary ◽  
Alpine Fault ◽  
Rupture Behavior
Sign in / Sign up

Export Citation Format

Share Document