Solid-state amorphization of As 45 S 55 alloy induced by high-energy mechanical milling

2016 ◽  
Vol 642 ◽  
pp. 59-66 ◽  
Author(s):  
O. Shpotyuk ◽  
A. Kozdras ◽  
P. Demchenko ◽  
Ya. Shpotyuk ◽  
Z. Bujňáková ◽  
...  
Keyword(s):  
Solid State ◽  
Mechanical Milling ◽  
High Energy ◽  
State Amorphization

Mechanism of solid-state amorphization of Se induced by mechanical milling

2004 ◽  
Vol 95 (12) ◽  
pp. 7674-7680 ◽  
Author(s):  
Y. H. Zhao ◽  
Y. T. Zhu ◽  
T. Liu
Keyword(s):  
Solid State ◽  
Mechanical Milling ◽  
State Amorphization

Solid state amorphization kinetic of alpha lactose upon mechanical milling

2011 ◽  
Vol 346 (16) ◽  
pp. 2622-2628 ◽  
Author(s):  
Vincent Caron ◽  
Jean-François Willart ◽  
Ronan Lefort ◽  
Patrick Derollez ◽  
Florence Danède ◽  
...  
Keyword(s):  
Solid State ◽  
Mechanical Milling ◽  
State Amorphization

Solid-State Amorphization of Linaprazan by Mechanical Milling and Evidence of Polymorphism

2013 ◽  
Vol 102 (7) ◽  
pp. 2214-2220 ◽  
Author(s):  
Jean-Francois Willart ◽  
Morgan Durand ◽  
Lars-Erik Briggner ◽  
Anke Marx ◽  
Florence Danède ◽  
...  
Keyword(s):  
Solid State ◽  
Mechanical Milling ◽  
State Amorphization

TEM study of amorphization of Cu and Ti foils by cold-rolling

1990 ◽  
Vol 48 (4) ◽  
pp. 146-147
Author(s):  
W. A. Chiou ◽  
N. L. Jeon ◽  
Genbao Xu ◽  
M. Meshii
Keyword(s):  
Solid State ◽  
Cold Rolling ◽  
High Energy ◽  
Rapid Quenching ◽  
Vapor Condensation ◽  
Metallic Alloys ◽  
Solid State Reactions ◽  
High Energy Particle ◽  
Amorphous Metallic Alloys ◽  
Thin Foils

For many years amorphous metallic alloys have been prepared by rapid quenching techniques such as vapor condensation or melt quenching. Recently, solid-state reactions have shown to be an alternative for synthesizing amorphous metallic alloys. While solid-state amorphization by ball milling and high energy particle irradiation have been investigated extensively, the growth of amorphous phase by cold-rolling has been limited. This paper presents a morphological and structural study of amorphization of Cu and Ti foils by rolling.Samples of high purity Cu (99.999%) and Ti (99.99%) foils with a thickness of 0.025 mm were used as starting materials. These thin foils were cut to 5 cm (w) × 10 cm (1), and the surface was cleaned with acetone. A total of twenty alternatively stacked Cu and Ti foils were then rolled. Composite layers following each rolling pass were cleaned with acetone, cut into half and stacked together, and then rolled again.

Sign in / Sign up

Export Citation Format

Share Document