Microstructural equivalence between bending and uniaxial creep

2020 ◽  
Vol 186 ◽  
pp. 99-103 ◽  
Author(s):  
Syed Idrees Afzal Jalali ◽  
Praveen Kumar ◽  
Vikram Jayaram
Keyword(s):  
Uniaxial Creep

A Study on Estimation of Internal Pressure Creep Life Using Small Punch Creep (SPC) Tests for Boiler Pipes

2009 ◽  
Author(s):  
Toshimi Kobayashi ◽  
Toru Izaki ◽  
Junichi Kusumoto ◽  
Akihiro Kanaya
Keyword(s):  
Internal Pressure ◽  
Residual Life ◽  
Test Results ◽  
Creep Life ◽  
Creep Tests ◽  
Good Correspondence ◽  
Small Punch ◽  
Uniaxial Creep ◽  
Wide Range ◽  
The Relationship

The small punch creep (SPC) test is possible to predict residual creep life at a high accuracy. But, the results of SPC tests cannot be compared with uniaxial creep or internal pressure creep results directly. In this report, the relationship between SPC test results and uniaxial creep test results in ASME A335 P11 (1.25Cr-0.5Mo Steel) was studied. The obtained relationship between SPC load and equivalent uniaxial creep stress formed a simple linear equation under the wide range of test temperature and test period. Then, the SPC results can be compared with uniaxial results by converting SPC loads to the equivalent uniaxial creep stresses. The relationship between SPC test results and internal pressure creep tests results was also studied. The internal creep life of as-received P11 pipe was almost same as SPC result when the hoop stress was converted to the SPC load. The creep lives of internal pressure creep influenced materials also showed good correspondence with SPC results. Therefore SPC can estimate the residual life of internal pressure creep influenced materials.

On the Measurement of Material Creep Parameters by Nanoindentation

2004 ◽  
Vol 841 ◽  
Author(s):  
J. A. LaManna ◽  
W. C. Oliver ◽  
G. M. Pharr
Keyword(s):  
Material Constant ◽  
Uniaxial Stress ◽  
Complete Characterization ◽  
Indentation Load ◽  
Amorphous Selenium ◽  
Load History ◽  
Time Data ◽  
Creep Equation ◽  
Uniaxial Creep ◽  
Material Creep

ABSTRACTPrevious studies of how material creep parameters can be measured by nanoindentation testing have focused mostly on measurement of the stress exponent for creep, n, and the activation energy, Qc. However, a more complete characterization requires that the material constant A in the uniaxial creep equation εu =Aσn (where εu is the uniaxial strain rate and σ is the uniaxial stress) also be evaluated. Here, we begin to address this issue by performing simple nanoindentation creep experiments in amorphous selenium at temperatures above and below the glass transition. At 35°C and above, the material exhibits a simple linear viscous creep behavior that is load history independent. This allows the parameter A to be determined from the indentation load-displacement-time data by means of an analytical solution. To examine the validity of the approach, values of the parameter A measured in nanoindentation tests are compared to independent measurements obtained in uniaxial tension creep experiments.

Modified Dyson Continuum Damage Model for Austenitic Steel Alloy

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Seok Jun Kang ◽  
Hoomin Lee ◽  
Jae Boong Choi ◽  
Moon Ki Kim
Keyword(s):  
Damage Model ◽  
Life Time ◽  
Continuum Damage ◽  
Creep Life ◽  
Creep Tests ◽  
Continuum Damage Model ◽  
Thermal Plant ◽  
Uniaxial Creep ◽  
Term Creep

Ultrasuper critical (USC) thermal plants are now in operation around the globe. Their applications include superheaters and reheaters, which generally require high temperature/pressure conditions. To withstand these harsh conditions, an austenitic heat-resistant HR3C (ASME TP310NbN) steel was developed for metal creep resistance. As the designed life time of a typical thermal plant is 150,000 h, it is very important to predict long-term creep behavior. In this study, a three-state variable continuum damage model (CDM) was modified for better estimation of long-term creep life. Accelerated uniaxial creep tests were performed to determine the material parameters. Also, the rupture type and microstructural precipitation were observed by scanning electron microscopy. The creep life of HR3C steel was predicted using only relatively short-term creep test data and was then successfully verified by comparison with the long-term creep data.

Creep Crack Growth Prediction of Very Long Term P91 Steel Using Extrapolated Short-Term Uniaxial Creep Data

2013 ◽  
Author(s):  
S. Maleki ◽  
A. Mehmanparast ◽  
K. M. Nikbin
Keyword(s):  
Crack Growth ◽  
Creep Crack Growth ◽  
Life Assessment ◽  
Short Term ◽  
Creep Crack ◽  
Uniaxial Creep ◽  
Laboratory Test Results ◽  
Area Of Concern ◽  
Term Creep

Practical time frames in newly developed steels, and technical and financial restrictions in test durations means that extrapolation of short-term laboratory test results to predict long-term high temperature service component failure is an area of concern when conducting a fitness for service or remaining life assessment. Recent literature presenting uniaxial creep and crack growth tests indicate that some materials show lower failure strains during longer term laboratory tests. The constraint based remaining failure ductility based NSW model crack prediction model has been shown to be capable of predicting upper/lower bounds of creep crack growth in a range of steels when data are obtained from relatively short to medium-term laboratory experiments (< 10,000 hours). This paper compares and analyses the response of the NSW model to predict long term creep crack propagation rates using a wide database of modified 9Cr material over s range of temperatures. The paper employs extrapolation methods of available uniaxial data to make viable conservative predictions of crack growth at high temperatures where at present no data is available.

Some Implications of a Nonlinear Viscoelastic Constitutive Theory Regarding Interrelationships Between Creep and Strength Behavior of Ice at Failure

1989 ◽  
Vol 111 (2) ◽  
pp. 144-148 ◽  
Author(s):  
B. D. Harper
Keyword(s):  
Strain Rate ◽  
Constant Strain Rate ◽  
Nonlinear Viscoelastic ◽  
Uniaxial Creep ◽  
Strength Behavior ◽  
Minimum Strain Rate ◽  
Strength Constant ◽  
Viscoelastic Constitutive Model ◽  
Stress And Strain Rate ◽  
Special Case

This study explores several possibilities for a correspondence in the behavior of ice at failure during uniaxial creep (constant stress) and strength (constant strain rate) experiments. The usual notion of failure in ice is employed (i.e., the occurrence of a minimum strain rate during a creep test and a peak or maximum stress during a strength test), and the behavior at failure is discussed in terms of a recently proposed nonlinear viscoelastic constitutive model for ice. It is demonstrated that no correspondence between creep and strength data can be expected in general; however, several approximate interrelationships do occur for the experimentally motivated special case of a constant (independent of stress and strain rate) failure strain.

Creep Rupture Properties

2004 ◽  
pp. 243-252
Keyword(s):  
Room Temperature ◽  
Creep Rupture ◽  
Aluminum Casting ◽  
Data Set ◽  
Raw Data ◽  
Casting Alloys ◽  
Uniaxial Creep ◽  
Wide Range ◽  
Rupture Properties

Abstract This data set contains the results of uniaxial creep rupture tests for a wide range of aluminum casting alloys conducted at temperatures from 100 to 315 deg C. In most cases, tests were made of several lots of material of each alloy and temper, the results were analyzed, and the averages were normalized to the room-temperature typical values. For some alloys, "representative" values (raw data) rather than typical values are provided.

scholarly journals Digital Volume Correlation Applied to X-ray Micro-Tomography Images in Uniaxial Creep Tests on Anisotropic Clayey Rock

2020 ◽  
Vol 10 (14) ◽  
pp. 4898
Author(s):  
Hailing Shi ◽  
Jerome Hosdez ◽  
Thomas Rougelot ◽  
Shouyi Xie ◽  
Jianfu Shao ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Clayey Rock ◽  
Digital Volume Correlation ◽  
Creep Tests ◽  
Structural Anisotropy ◽  
Strain Fields ◽  
X Ray ◽  
Bedding Planes ◽  
Uniaxial Creep ◽  
Micro Tomography

Creep tests are commonly performed to characterize time-dependent deformation of geological materials. Classical measuring methods are not suitable for long term tests and not able to provide full three-dimensional strain fields. In this study, Digital Volume Correlation (DVC) is applied to X-ray micro-tomography (XRMT) images from creep tests on a hard clayey rock. In situ uniaxial compression creep tests are performed under different levels of stress and with different loading orientations with respect to the structural anisotropy of rock. Based on the XRMT images taken during the creep tests, DVC is applied to compute the full three dimensional strain fields and global averages strains of tested samples. The effects of bedding planes and hard inclusions on the non-uniform distribution of strains are analyzed.

Sign in / Sign up

Export Citation Format

Share Document