Tensile deformation characteristics of bulk ultrafine-grained austenitic stainless steel produced by thermal cycling

2012 ◽  
Vol 66 (9) ◽  
pp. 634-637 ◽  
Author(s):  
B. Ravi Kumar ◽  
Dierk Raabe
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Thermal Cycling ◽  
Tensile Deformation ◽  
Deformation Characteristics ◽  
Ultrafine Grained

Effects of Deformation Mode on Resistivity Curve Used for Estimating Martensite Induced in Stainless Steel

2010 ◽  
Vol 638-642 ◽  
pp. 2992-2997 ◽  
Author(s):  
Hidefumi Date
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Linear Relation ◽  
Volume Fraction ◽  
Tensile Deformation ◽  
Deformation Mode ◽  
Transformation Process ◽  
Martensite Formation ◽  
Austenitic Phase ◽  
Ε Phase

The martensite induced in three types of austenitic stainless steel, which indicate the different stability of the austenitic phase (γ), were estimated by the resistivity measured during the tensile deformation or compressive deformation at the temperatures 77, 187 and 293 K. The resistivity curves were strongly dependent on the deformation mode. The volume fraction of the martensite (α’) was also affected by the deformation mode. The ε phase, which is the precursor of the martensite and is induced from the commencement of the deformation, decreased the resistivity. However, lots of defects generated by the deformation-induced martensite increased the resistivity. The experimental facts and the results shown by the modified parallelepiped model suggested a complicated transformation process depending on each deformation mode. The results shown by the model also suggested a linear relation between the resistivity and the martensite volume at the region of the martensite formation. The fact denoted that the resistivity is mostly not controlled by the austenite, ε phase and martensite, but by the defects induced due to the deformation-induced martensite.

Favorable Modulation of Pre-Osteoblast Response to Nanograined/Ultrafine-grained Structures in Austenitic Stainless Steel

2009 ◽  
Vol 21 (12) ◽  
pp. 1280-1285 ◽  
Author(s):  
R.D.K. Misra ◽  
W-W. Thein-Han ◽  
T.C. Pesacreta ◽  
K.H. Hasenstein ◽  
M.C. Somani ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Ultrafine Grained

In-situ EBSD study of the degradation behavior in a type 316 Austenitic Stainless Steel during plastic deformation

2021 ◽  
pp. 030932472098493
Author(s):  
Xiao Wang ◽  
Yuetao Zhang ◽  
Huaying Li ◽  
Ming-yu Huang
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Tensile Deformation ◽  
Target Surface ◽  
Local Orientation ◽  
Deformation Degree ◽  
Band Contrast

Type 316 steels have been heavily utilized as the structural material in many construction equipment and infrastructures. This paper reports the characterization of degradation in 316 austenitic stainless steel during the plastic deformation. The in-situ EBSD results revealed that, with the increase of plastic strain, the band contrast (BC) value progressively decreased in both grain and grain boundaries, and the target surface becomes uneven after the plastic tensile, which indicates that the increase of surface roughness. Meanwhile, the KAM and ρGND values are low in the origin specimen but increased significantly after the in-situ tensile. The results indicated that the KAM and ρGND are closely related to the deformation degree of the materials, which can be used as the indicator for assessing the degradation of 316 steel. Besides, the re-orientation of grain occurred after the tensile deformation, which can be recognized from the lattice orientation and local orientation maps.

The effect of neutron irradiation on the impact toughness of austenitic stainless steel in ultrafine-grained state

2021 ◽  
Vol 544 ◽  
pp. 152680
Author(s):  
Valentin K. Shamardin ◽  
Tatyana M. Bulanova ◽  
Alexander E. Fedoseev ◽  
Alexei A. Karsakov ◽  
Ruslan Z. Valiev ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Toughness ◽  
Neutron Irradiation ◽  
Ultrafine Grained ◽  
The Impact

scholarly journals A 2.9 GPa Strength Nano-Grained and Nano-Precipitated 304L-Type Austenitic Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5382
Author(s):  
Congcong Du ◽  
Guoying Liu ◽  
Baoru Sun ◽  
Shengwei Xin ◽  
Tongde Shen
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Yield Strength ◽  
Average Particle Size ◽  
Coarse Grained ◽  
Average Particle ◽  
Dispersion Strengthening ◽  
Ultrafine Grained ◽  
Average Grain Size ◽  
Bulk Nanocrystalline

Austenitic stainless steel has high potential as nuclear and engineering materials, but it is often coarse grained and has relatively low yield strength, typically 200–400 MPa. We prepared a bulk nanocrystalline lanthanum-doped 304L austenitic stainless steel alloy by a novel technique that combines mechanical alloying and high-pressure sintering. The achieved alloy has an average grain size of 30 ± 12 nm and contains a high density (~1024 m−3) of lanthanum-enriched nanoprecipitates with an average particle size of approx. 4 nm, leading to strong grain boundary strengthening and dispersion strengthening effects, respectively. The yield strength of nano-grained and nano-precipitated stainless steel reaches 2.9 GPa, which well exceeds that of ultrafine-grained (100–1000 nm) and nano-grained (<100 nm) stainless steels prepared by other techniques developed in recent decades. The strategy to combine nano-grain strengthening and nanoprecipitation strengthening should be generally applicable to developing other ultra-strong metallic alloys.

Sign in / Sign up

Export Citation Format

Share Document