scholarly journals Numerical Prediction of Fusion Zone and Heat Affected Zone in Hybrid Yb:YAG laser + GMAW Welding Process with Experimental Verification

2016 ◽  
Vol 136 ◽  
pp. 88-94 ◽  
Author(s):  
Marcin Kubiak ◽  
Wiesława Piekarska ◽  
Zbigniew Saternus ◽  
Tomasz Domański
Keyword(s):  
Fusion Zone ◽  
Experimental Verification ◽  
Heat Affected Zone ◽  
Welding Process ◽  
Numerical Prediction ◽  
Gmaw Welding

scholarly journals Influence of Welding Parameters On Grain Size, Haz and Degree of Dilution in 6063-t5 Alloy. Optimisation Through the Taguchi Method of the Gmaw Welding Process.

2022 ◽  
Author(s):  
Jose Luis Meseguer Valdenebro ◽  
Eusebio José Martínez Conesa ◽  
Antonio Portoles
Keyword(s):  
Grain Size ◽  
Taguchi Method ◽  
Heat Affected Zone ◽  
Welding Process ◽  
Welding Parameter ◽  
Welding Parameters ◽  
Taguchi’S Method ◽  
Gmaw Welding ◽  
Made In

Abstract The aim of this work is to carry out the design of experiments that determine the influence of the welding parameters using Taguchi’s method on the grain size, HAZ, and the degree of dilution in 6063-T5 alloy. The welding process used is GMAW and the welding parameters are power, welding speed and bevel spacing. The study of the influence of the welding parameters on the measurements made in the welding (which are the size of heat affected zone, the degree of dilution, and the grain size) allows one to determine the quality of the joint . In addition, the welding parameter most influential in minimising the three measurements will be determined.

Investigations on Laser-TIG Hybrid Welding of Magnesium Alloys

2005 ◽  
Vol 488-489 ◽  
pp. 371-376 ◽  
Author(s):  
Gang Song ◽  
Li Ming Liu ◽  
Mingsheng Chi ◽  
Ji Feng Wang
Keyword(s):  
Magnesium Alloys ◽  
Fusion Zone ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welding Process ◽  
Large Change ◽  
Tig Welding ◽  
Al Content ◽  
Β Phase ◽  
Cast Magnesium

This paper presents results of recent investigations on the weldability of several wrought (AZ31, AZ61) and cast magnesium-based alloys (AZ91) by laser-TIG welding process. The investigations showed that magnesium alloys can be easily welded by laser-TIG welding. The grain of the fusion zone was finer than that of in base metal. The width of the heat-affected zone welded by laser-TIG welding process was obviously narrower than that of welded by TIG. Besides, with the Al content of magnesium alloys increasing, the width of the heat-affected zone (HAZ) was increased，as well as the content of β phase(Mg17Al12). The hardness in the fusion zone (FZ) and in HAZ of AZ61 and AZ91 has a large change to the base metal due to the existing of β phase, while no change relative for AZ31. It results from above discussing that laser-TIG welding is an excellent welding process for magnesium alloys.

Metodología para el desarrollo de trayectorias en la aplicación por el proceso de soldadura GMAW en un robot industrial

2019 ◽  
pp. 1-4
Author(s):  
Josué Rafael Sánchez-Lerma ◽  
Luis Armando Torres-Rico ◽  
Héctor Huerta-Gámez ◽  
Ismael Ruiz-López
Keyword(s):  
Mechanical Properties ◽  
Automotive Industry ◽  
Industrial Robot ◽  
Welding Process ◽  
High Strength ◽  
Test Material ◽  
Advantages And Disadvantages ◽  
Application Characteristics ◽  
Joining Process ◽  
Gmaw Welding

This paper proposes the development of the methodology to be carried out for the metal joining process through the GMAW welding process in the Fanuc LR Mate 200iD industrial robot. The parameters or properties were considered for the application to be as efficient as possible, such parameters as speed of application, characteristics of the filler material, gas to be used as welding protection. The GMAW welding process can be applied semiautomatically using a hand gun, in which the electrode is fed by a coil, or an automatic form that includes automated equipment or robots. The advantages and disadvantages of the GMAW welding process applied in a manual and automated way were commented. The mechanical properties of the materials to which said welding can be applied were investigated; The materials with which this type of welding can be worked are the high strength materials, which are used in the automotive industry, for the forming of sheet metal. To know the properties of the material, destructive tests were carried out on the test material to be used, as well as the mechanical properties of the welding.

Double-Electrode GMAW Welding Process Research Based on the DSC

2013 ◽  
Vol 668 ◽  
pp. 321-324 ◽  
Author(s):  
Guo Hong Ma ◽  
Jun Nie ◽  
Chao Yang Zhang ◽  
Jia Ye
Keyword(s):  
Magnesium Alloy ◽  
Welding Process ◽  
Alloy Sheet ◽  
Process Research ◽  
Az31b Magnesium Alloy ◽  
Magnesium Alloy Sheet ◽  
Double Electrode ◽  
Az31b Magnesium Alloy Sheet ◽  
Gmaw Welding

Through a large number of technology experiments, finding out the matching parameters of the DE-GMAW welding of the AZ31B magnesium alloy sheet based on the DSC. This paper simply controls the motor based on the DSC to control the welding torches moving comfortably to make the welding process stable to obtain the good weld.

Influence of Thermal Simulated and Real Tandem Submerged Arc Welding Process on the Microstructure and Mechanical Properties of the Coarse Grained Heat Affected Zone

2011 ◽  
Vol 110-116 ◽  
pp. 3191-3198
Author(s):  
Sadegh Moeinifar
Keyword(s):  
Grain Boundaries ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Arc Welding ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
Rolled Plate ◽  
Arc Welding Process ◽  
Submerged Arc ◽  
Tandem Submerged Arc Welding

The high-strength low-alloy microalloyed steel was procured as a hot rolled plate with accelerated cooling. The Gleeble thermal simulated process involved heating the steel specimens to the peak temperature of 1400 °C, with constant cooling rates of 3.75 °C/s and 2 °C/s to room temperature. The four-wire tandem submerged arc welding process, with different heat input, was used to generate a welded microstructure. The martensite/austenite constituent appeared in the microstructure of the heat affected zone region for all the specimens along the prior-austenite grain boundaries and between bainitic ferrite laths. The blocky-like and stringer martensite/austenite morphology were observed in the heat affected zone regions. The martensite/austenite constituents were obtained by a combination of field emission scanning electron microscopes and image analysis software The Charpy absorbed energy of specimens was assessed using Charpy impact testing at-50 °C. Brittle particles, such as martensite/austenite constituent along the grain boundaries, can make an easy path for crack propagation. Similar crack initiation sites and growth mechanism were investigated for specimens welded with different heat input values.

Effects of Welding Wire Composition on Microstructure and Mechanical Properties of Welded Joint in Al-Mg-Si Alloy

2022 ◽  
Vol 905 ◽  
pp. 44-50
Author(s):  
Li Wang ◽  
Ya Ya Zheng ◽  
Shi Hu Hu
Keyword(s):  
Mechanical Properties ◽  
Fusion Zone ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Weld Zone ◽  
Xrd Analysis ◽  
Metallographic Analysis ◽  
Strengthening Effect ◽  
Welding Wire ◽  
Microstructure And Mechanical Properties

The effects of welding wire composition on microstructure and mechanical properties of welded joint in Al-Mg-Si alloy were studied by electrochemical test, X-ray diffraction (XRD) analysis and metallographic analysis. The results show that the weld zone is composed of coarse columnar dendrites and fine equated grains. Recrystallized grains are observed in the fusion zone, and the microstructure in the heat affected zone is coarsened by welding heat. The hardness curve of welded joint is like W-shaped, the highest hardness point appears near the fusion zone, and the lowest hardness point is in the heat affected zone. The main second phases of welded joints are: matrix α-Al, Mg2Si, AlMnSi, elemental Si and SiO2. The addition of rare earth in welding wire can refine the grain in weld zone obviously, produce fine grain strengthening effect, and improve the electrochemical performance of weld.

scholarly journals Numerical Prediction of Feasibility to Lower Droplet Temperature in Duplex Current Feeding MIG Welding Process

2020 ◽  
Vol 38 (2) ◽  
pp. 44s-48s
Author(s):  
Shinichi TASHIRO ◽  
Atsuhito AOKI ◽  
Hideaki KUROAWA ◽  
Manabu TANAKA
Keyword(s):  
Welding Process ◽  
Numerical Prediction ◽  
Droplet Temperature ◽  
Mig Welding
Sign in / Sign up

Export Citation Format

Share Document