scholarly journals Study on the Effect of Post Weld Heat Treatment Parameters on the Relaxation of Welding Residual Stresses in Electron Beam Welded P91 Steel Plates

2014 ◽  
Vol 86 ◽  
pp. 223-233 ◽  
Author(s):  
K. Abburi Venkata ◽  
S. Kumar ◽  
H.C. Dey ◽  
D.J. Smith ◽  
P.J. Bouchard ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electron Beam ◽  
Residual Stresses ◽  
Post Weld Heat Treatment ◽  
Steel Plates ◽  
P91 Steel ◽  
Weld Heat

Measurement of Residual Stresses in Thick Section Steel Electron Beam Welds

2010 ◽  
Author(s):  
E. Kingston ◽  
D. J. Smith ◽  
G. Zheng ◽  
C. Gill ◽  
P. Hurrell
Keyword(s):  
Heat Treatment ◽  
Electron Beam ◽  
Residual Stresses ◽  
Post Weld Heat Treatment ◽  
Hole Drilling ◽  
Drilling Technique ◽  
Fair Comparison ◽  
Before And After ◽  
Hoop Stresses ◽  
Weld Heat

Residual stresses were measured and predicted in steel electron beam welded samples, one supplied by Rolls-Royce, UK, and a second by CEA, France. In the case of the Rolls-Royce sample, measurements were made before and after post-weld heat treatment. The deep hole drilling technique was applied to obtain measurements across and through the EB welds. It is shown that the tensile residual stresses are confined to a region either side of the EB weld that corresponds to about 20% of the wall thickness. Post-weld heat treatment is shown to substantially reduce the magnitudes of the peak residual stresses. Comparisons between measurements and predicted residual stresses in the Rolls-Royce sample show that predicted hoop stresses are substantially greater than measured although there is a fair comparison between measured and predicted radial stresses.

scholarly journals Comparison of measured and modelled residual stresses in a welded P91 steel pipe undergoing post weld heat treatment

2020 ◽  
Vol 181 ◽  
pp. 104076 ◽  
Author(s):  
Anas H. Yaghi ◽  
Thomas H. Hyde ◽  
Adib A. Becker ◽  
Wei Sun ◽  
Wu Wen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
Post Weld Heat Treatment ◽  
Steel Pipe ◽  
P91 Steel ◽  
Weld Heat

scholarly journals Residual Stress State of X65 Pipeline Girth Welds Before and After Local and Furnace Post Weld Heat Treatment

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Yao Ren ◽  
Anna Paradowska ◽  
Bin Wang ◽  
Elvin Eren ◽  
Yin Jin Janin
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Residual Stresses ◽  
Outer Surface ◽  
Post Weld Heat Treatment ◽  
Pipe Length ◽  
Stress Profiles ◽  
Girth Welds ◽  
Welded Pipe ◽  
Weld Heat

This research investigated the effects of global (in other words, furnace-based) and local post weld heat treatment (PWHT) on residual stress (RS) relaxation in API 5L X65 pipe girth welds. All pipe spools were fabricated using identical pipeline production procedures for manufacturing multipass narrow gap welds. Nondestructive neutron diffraction (ND) strain scanning was carried out on girth welded pipe spools and strain-free comb samples for the determination of the lattice spacing. All residual stress measurements were carried out at the KOWARI strain scanning instrument at the Australian Nuclear Science and Technology Organization (ANSTO). Residual stresses were measured on two pipe spools in as-welded condition and two pipe spools after local and furnace PWHT. Measurements were conducted through the thickness in the weld material and adjacent parent metal starting from the weld toes. Besides, three line-scans along pipe length were made 3 mm below outer surface, at pipe wall midthickness, and 3 mm above the inner surface. PWHT was carried out for stress relief; one pipe was conventionally heat treated entirely in an enclosed furnace, and the other was locally heated by a flexible ceramic heating pad. Residual stresses measured after PWHT were at exactly the same locations as those in as-welded condition. Residual stress states of the pipe spools in as-welded condition and after PWHT were compared, and the results were presented in full stress maps. Additionally, through-thickness residual stress profiles and the results of one line scan (3 mm below outer surface) were compared with the respective residual stress profiles advised in British Standard BS 7910 “Guide to methods for assessing the acceptability of flaws in metallic structures” and the UK nuclear industry's R6 procedure. The residual stress profiles in as-welded condition were similar. With the given parameters, local PWHT has effectively reduced residual stresses in the pipe spool to such a level that it prompted the thought that local PWHT can be considered a substitute for global PWHT.

The BWR RPV Internals Management Program of the German NPP Gundremmingen, Units B and C: Results and Conclusions

2002 ◽  
Author(s):  
Martin Widera
Keyword(s):  
Heat Treatment ◽  
Crack Initiation ◽  
Residual Stresses ◽  
Surface Condition ◽  
Management Program ◽  
Post Weld Heat Treatment ◽  
Interim Result ◽  
The Core ◽  
Weld Heat ◽  
Core Shroud

Due to the core shroud cracks reported from numerous BWRs including the German KWU type BWR Wuergassen, a RPV internals management program for the Gundremmingen NPP (KRB-II) has been initiated in 1994. Major steps and the main results of this program are presented. As an interim result, surface condition of the weld regions and controlled post weld heat treatment (PWHT) in order to reduce the residual stresses seem to play an important role for resistance to crack initiation and growth. To support these assumptions, results of related R&D projects of the German utilities (VGB) are presented.

Engineering Critical Assessment of Post Weld Heat Treatment for Full-Encirclement Tees Greater Than 1.25 Inches

2019 ◽  
Author(s):  
Kolton Landreth ◽  
Qi Li ◽  
Raghav Marwaha
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
Critical Assessment ◽  
Material Strength ◽  
Mechanical Reinforcement ◽  
Element Analysis ◽  
Pipeline Design ◽  
Weld Heat

Abstract Full-encirclement split tee fittings for hot tapping and plugging (HT&P) wrap completely around the pipeline and are welded in place. The welded joint provides mechanical reinforcement of the pipe and branch. When full-encirclement hot tap tees are welded to pipelines 24 inches in diameter or larger, the header must often be at least 1.25 inches thick to pass the required calculations for reinforcement. This means the joint will require post weld heat treatment (PWHT) according to ASME B31.8 and CSA Z662. However, PWHT can be extremely dangerous and impractical, potentially elevating temperature to the point where material strength of the pressurized pipeline is compromised. An engineering critical assessment per ASME FFS-1/API 579 indicated PWHT may not be required for a full-encirclement hot tap tee over 1.25 inches thick. Specifically, research showed that the residual stresses developed during the welding process may not limit the design of a full-encirclement tee or lead to shorter pipeline design life. This paper illustrates how a “more rigorous analysis” per paragraph 802.2.2[b] of ASME B31.8 and paragraph 4.3.12.2 of CSA Z662 may help operators avoid the PWHT requirement. It discusses the finite element analysis (FEA) simulations researchers used to induce residual stresses in a carbon steel fitting. The residual stresses induced in the fitting were used as initial condition for plastic collapse and fatigue evaluations.

Establishing Recommended Guidance for Local Post Weld Heat Treatment Configurations Based on Thermal-Mechanical Finite Element Analysis

2016 ◽  
Author(s):  
Phillip E. Prueter ◽  
Brian Macejko
Keyword(s):  
Heat Treatment ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Crack Initiation ◽  
Residual Stresses ◽  
Pressure Vessel ◽  
Post Weld Heat Treatment ◽  
Element Analysis ◽  
Non Linear ◽  
Weld Heat

Post weld heat treatment (PWHT) is an effective way to minimize weld residual stresses in pressure vessels and piping equipment. PWHT is required for carbon steels above a Code-defined thickness threshold and other low-alloy steels to mitigate the propensity for crack initiation and ultimately, brittle fracture. Additionally, PWHT is often employed to mitigate stress corrosion cracking due to environmental conditions. Performing local PWHT following component repairs or alterations is often more practical and cost effective than heat treating an entire vessel or a large portion of the pressure boundary. In particular, spot or bulls eye configurations are often employed in industry to perform PWHT following local weld repairs to regions of the pressure boundary. Both the ASME Boiler and Pressure Vessel (B&PV) Code and the National Board Inspection Code (NBIC) permit the use of local PWHT around nozzles or other pressure boundary repairs or alterations. Additionally, Welding Research Council (WRC) Bulletin 452 [1] offers detailed guidance relating to local PWHT and compares some of the Code-based methodologies for implementing local PWHT on pressure retaining equipment. Specifically, local PWHT methodologies provided in design Codes: ASME Section VIII Division 1 [2] and Division 2 [3], ASME Section III Subsection NB [4], British Standard 5500 [5], Australian Standard 1210 [6], and repair Codes: American Petroleum Institute (API) 510 [7] and NBIC [8] are discussed and compared in this study. While spot PWHT may be appropriate in certain cases, if the soak, heating, and gradient control bands are not properly sized and positioned, it can lead to permanent vessel distortion or detrimental residual stresses that can increase the likelihood of in-service crack initiation and possible catastrophic failure due to unstable flaw propagation. It is essential to properly engineer local or spot PWHT configurations to ensure that distortion, cracking of adjacent welds, and severe residual stresses are avoided. In some cases, this may require advanced thermal-mechanical finite element analysis (FEA) to simulate the local PWHT process and to predict the ensuing residual stress state of the repaired area. This paper investigates several case studies of local PWHT configurations where advanced, three-dimensional FEA is used to simulate the thermal-mechanical response of the repaired region on a pressure vessel and to optimize the most ideal PWHT arrangement. Local plasticity and distortion are quantified using advanced non-linear elastic-plastic analysis. Commentary on the ASME and NBIC Code-specified local PWHT requirements is rendered based on the detailed non-linear FEA results, and recommended good practice for typical local PWHT configurations is provided. Advanced computational simulation techniques such as the ones employed in this investigation offer a means for analysts to ensure that local PWHT configurations implemented following equipment repairs will not lead to costly additional damage, such as distortion or cracking that can ultimately prolong equipment downtime.

Sign in / Sign up

Export Citation Format

Share Document