scholarly journals Room-temperature Multi-directional Forging of AZ80Mg Alloy to Induce Ultrafine Grained Structure and Specific Mechanical Properties

2014 ◽  
Vol 81 ◽  
pp. 534-539 ◽  
Author(s):  
Hiromi Miura ◽  
Wataru Nakamura ◽  
Masakazu Kobayashi
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Ultrafine Grained Structure ◽  
Ultrafine Grained

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

Effects of Temperature and Strain Rate on Compressive Mechanical Properties of Ultrafine-Grained CP Titanium

2007 ◽  
Vol 26-28 ◽  
pp. 381-384 ◽  
Author(s):  
Zhi Guo Fan ◽  
Chao Ying Xie
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Ultimate Strength ◽  
Room Temperature ◽  
Equal Channel Angular Extrusion ◽  
Coarse Grain ◽  
Ultrafine Grained ◽  
Effects Of Temperature ◽  
Cp Ti ◽  
Compressive Tests

Ultrafine-grained (UFG) CP Ti were successfully prepared by Equal Channel Angular Extrusion (ECAE) at 390°C~400°C, small than 0.5 um in size. The compressive tests for coarse grain (CG) and UFG Ti were carried out at room temperature (RT) and 77K. UFG Ti showed excellent ductility and higher strength than CG Ti at RT and 77 K. The strain hardening of UFG Ti was improved at 77 K. The compressive ultimate strengths of CG Ti and UFG Ti were both enhanced as the strain rate increased, but CG Ti showed more obvious temperature and strain rate dependence of flow stress, comparing with UFG Ti. When the strain rate increased to 1×10-1/s, the compressive ultimate strength of UFG Ti was kept almost constant, while the ultimate strength of CG Ti increased to the strength level of UFG Ti.

Mechanical Nanocrystallization Surface Treatment on the Reheated 400MPa Ultrafine Grained Steel

2009 ◽  
Vol 79-82 ◽  
pp. 377-380
Author(s):  
Hong Yun Zhao ◽  
Guo Dong Wang ◽  
Chun Hua Xu ◽  
Feng Yuan Shu
Keyword(s):  
Mechanical Properties ◽  
Surface Treatment ◽  
Room Temperature ◽  
Performance Testing ◽  
Surface Form ◽  
Test Results ◽  
Ultrafine Grained ◽  
Before And After ◽  
Different Temperatures ◽  
Ultrafine Grained Steel

After reheated at different temperatures for 5 minutes, the 400MPa Ultrafine Grained Steel specimens were air-cooled to room temperature, and then carried out the mechanical nanocrystallization surface treatment and structure performance testing. On the basis of comparing the test results on the specimens before and after the mechanical nanocrystallization surface treatment, the process of mechanical nanocrystallization was analyzed briefly. The results show that: as the reheating temperature rising, the trend of grain size growing increases markedly, and the mechanical properties also drop down to different degrees; when the reheating temperature is around 800°C, because of the pearlite spheroidized significantly, its mechanical properties drop the most seriously; after the mechanical nanocrystallization surface treatment, not only its surface form a layer of fine nano-layer (about 100 nm) structure, but also its mechanical properties rise obviously, and the yield strength is over 450MPa.

scholarly journals Preparation of Ultrafine-Grained Continuous Chips by Cryogenic Large Strain Machining

Metals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 398
Author(s):  
Haitao Chen ◽  
Baoyu Zhang ◽  
Jiayang Zhang ◽  
Wenjun Deng
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Dynamic Recovery ◽  
Large Strain ◽  
Chip Morphology ◽  
Machining Parameters ◽  
Orthogonal Machining ◽  
Solute Cluster ◽  
Ultrafine Grained ◽  
Al 7075

Conventional orthogonal machining is an effective severe plastic deformation (SPD) method to fabricate ultrafine-grained (UFG) materials. However, UFG materials produced by room temperature-free machining (RT-FM) are prone to dynamic recovery, which decreases the mechanical properties of UFG materials. In this study, the cryogenic orthogonal machining technique was implemented to fabricate chips that have an abundant UFG microstructure. Solution-treated Al-7075 bulk has been processed in cryogenic temperature (CT) and room temperature (RT) with various machining parameters, respectively. The microstructure, chip morphology and mechanical properties of CT and RT samples have been investigated. CT samples can reach a microhardness of 167.46 Hv, and the hardness of CT samples is higher than that of the corresponding RT samples among all parameters, with an average difference of 5.62 Hv. Piecemeal chip obtained under RT has cracks on its free surface, and elevated temperature aggravates crack growth, whereas all CT samples possess smoother surfaces and continuous shape. CT suppresses dynamic recovery effectively to form a heavier deformation microstructure, and with a higher dislocation density in CT samples, they further improve the chips’ hardness. Also, CT inhibits the formation of solute cluster and precipitation to enhance the formability of material, so that continuous chips are formed.

Mechanical Properties of an Al-Mg-Sc Alloy Subjected to Intense Plastic Straining

2010 ◽  
Vol 638-642 ◽  
pp. 1952-1958 ◽  
Author(s):  
Rustam Kaibyshev ◽  
Elena Avtokratova ◽  
O.S. Sitdikov
Keyword(s):  
Mechanical Properties ◽  
Cold Rolling ◽  
Yield Stress ◽  
Room Temperature ◽  
Total Elongation ◽  
Warm Rolling ◽  
Ultimate Stress ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
High Reduction

Effect of intense plastic straining on rollability and service properties of an Al-6%Mg-0.3%Sc alloy was examined. Ultrafine-grained structure (UFG) was produced by equal-channel angular pressing (ECAP) to a strain of 8 at a temperature of 325oC. The formation of UFG structure resulted in increase in the yield stress from 223 MPa to 285 MPa and ultimate stress from 350 MPa to 389 MPa in comparison with initial hot extruded condition. Total elongation slightly decreased from 33% to 29%. After ECAP, the material was subjected to cold and isothermal warm rolling. The formation of UFG structure resulted in enhanced rollability of the present alloy at room temperature. Cold rolling with high reduction provides the development of heavily deformed microstructure with high dislocation density, while the isothermal warm rolling does not remarkably affect the microstructure produced by ECAP. The mechanical properties after ECAP and ECAP with subsequent isothermal rolling were roughly similar. In contrast, cold rolling to the same strain resulted in significant increase of yield stress (495 MPa) and ultimate stress (536 MPa). Total elongation attained was 13%.

scholarly journals The influence of ultrafine‐grained structure on the mechanical properties and biocompatibility of austenitic stainless steels

2020 ◽  
Vol 108 (4) ◽  
pp. 1460-1468
Author(s):  
Olga V. Rybalchenko ◽  
Natalia Yu. Anisimova ◽  
Mikhail V. Kiselevsky ◽  
Andrey N. Belyakov ◽  
Aleksei A. Tokar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Ultrafine Grained Structure ◽  
Ultrafine Grained

Microstructure and Properties of Ti Rods Produced by Multi-Step SPD

2006 ◽  
Vol 503-504 ◽  
pp. 763-768 ◽  
Author(s):  
V.V. Latysh ◽  
Irina P. Semenova ◽  
G.H. Salimgareeva ◽  
I.V. Kandarov ◽  
Yuntian T. Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Stress ◽  
Equal Channel Angular Pressing ◽  
Thermomechanical Treatment ◽  
Ultrafine Grained Structure ◽  
Annealed State ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Cp Ti

This paper studies the effect of combined SPD treatment on microstructure and mechanical properties of semi-products out of CP Ti. The combined processing, consisting of equal-channel angular pressing and further thermomechanical treatment, produced ultrafine-grained rods out of Grade 2 CP Ti with a diameter of 6.5 mm and a length of up to 1 m. It was established that the formation of homogeneous ultrafine-grained structure in Ti rod with α-grain size of about 100 nm allowed to enhance yield stress by 200% in comparison with initial annealed state.

Sign in / Sign up

Export Citation Format

Share Document