scholarly journals Wind Turbine Performance Improvements using Active Flow Control Techniques

2012 ◽  
Vol 49 ◽  
pp. 83-91 ◽  
Author(s):  
S. Shun ◽  
N.A. Ahmed
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Active Flow Control ◽  
Control Techniques ◽  
Performance Improvements ◽  
Turbine Performance ◽  
Active Flow

High Efficiency Wind Turbine Using Co-Flow Jet Active Flow Control

2021 ◽  
Author(s):  
Kewei Xu ◽  
Gecheng Zha
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Flow Separation ◽  
Power Output ◽  
Pitch Angle ◽  
Active Flow Control ◽  
Horizontal Axis Wind Turbine ◽  
Negative Power ◽  
Freestream Velocity ◽  
Active Flow

Abstract This paper applies Co-flow Jet (CFJ) active flow control airfoil to a NREL horizontal axis wind turbine for power output improvement. CFJ is a zero-net-mass-flux active flow control method that dramatically increases airfoil lift coefficient and suppresses flow separation at a low energy expenditure. The 3D Reynolds Averaged Navier-Stokes (RANS) equations with one-equation Spalart-Allmaras (SA) turbulence model are solved to simulate the 3D flows of the wind turbines. The baseline wind turbine is the NREL 10.06m diameter phase VI wind turbine and is modified to a CFJ blade by implementing CFJ along the span. The baseline wind turbine performance is validated with the experiment at three wind speeds, 7m/s, 15m/s, and 25m/s. The predicted blade surface pressure distributions and power output agree well with the experimental measurements. The study indicates that the CFJ can enhance the power output at the condition where angle of attack is increased to the level that conventional wind turbine is stalled. At the speed of 7m/s that the NREL turbine is designed to achieve the optimum efficiency at the pitch angle of 3°, the CFJ turbine does not increase the power output. When the pitch angle is reduced by 13° to −10°, the baseline wind turbine is stalled and generates negative power output at 7m/s. But the CFJ wind turbine increases the power output by 12.3% assuming CFJ fan efficiency of 80% at the same wind speed. This is an effective method to extract more power from the wind at all speeds. It is particularly useful at low speeds to decrease cut-in speed and increase power output without exceeding the structure limit. At the freestream velocity of 15m/s and the CFJ momentum coefficient Cμ of 0.23, the net power output is increased by 207.7% assuming the CFJ fan efficiency of 80%, compared to the baseline wind turbine due to the removal of flow separation. The CFJ wind turbine appears to open a door to a new area of wind turbine efficiency improvement and adaptive control for optimal loading.

Numerical investigation of active flow control with co-flowing jet in a horizontal axis wind turbine

2020 ◽  
pp. 0309524X2096139
Author(s):  
Fangrui Shi ◽  
Yingqiao Xu ◽  
Xiaojing Sun
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Performance Enhancement ◽  
Active Flow Control ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Suction Surface ◽  
Horizontal Axis Wind Turbine ◽  
Momentum Coefficient ◽  
Active Flow

In this paper, a three-dimensional numerical simulation of the aerodynamic performance of a horizontal axis wind turbine (HAWT) whose blades are equipped with a new active flow control concept called Co-Flowing Jet (CFJ) is carried out. Numerical results show that the use of CFJ over the blade suction surface can effectively delay flow separation, thus improving the net torque and power output of HAWT. Besides, this increment in the net power produced by the turbine is considerably higher than the power consumed by the CFJ. Thus, the overall efficiency of the HAWT can be greatly increased. Furthermore, influences of different CFJ operating parameters including location of injection port, jet momentum coefficient and slot length on the performance enhancement of a HAWT are also systematically studied and the optimal combination of these parameters to obtain the best possible turbine efficiency throughout a range of different wind speeds has been identified.

Trailing edge noise reduction of wind turbine blades by active flow control

Wind Energy ◽  
2014 ◽  
Vol 18 (5) ◽  
pp. 909-923 ◽  
Author(s):  
Alexander Wolf ◽  
Thorsten Lutz ◽  
Werner Würz ◽  
Ewald Krämer ◽  
Oksana Stalnov ◽  
...  
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Noise Reduction ◽  
Active Flow Control ◽  
Turbine Blades ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Trailing Edge Noise ◽  
Active Flow

scholarly journals Performance Optimization of Wind Turbine Rotors with Active Flow Control (Part 1)

2012 ◽  
Vol 134 (04) ◽  
pp. 51-51 ◽  
Author(s):  
G. Pechlivanoglou ◽  
C.N. Nayeri ◽  
C.O. Paschereit
Keyword(s):  
Neural Network ◽  
Flow Control ◽  
Wind Turbine ◽  
Performance Optimization ◽  
Active Flow Control ◽  
Fine Tuning ◽  
Dynamic Force ◽  
Empirical Parameter ◽  
Turbine Rotors ◽  
Active Flow

This article describes the performance optimization of wind turbine rotors with active flow control. The active Gurney flap concept was tested in the wind tunnel under dynamic AoA variations to simulate unsteady inflow conditions. A high-deflection micro flap was actuated by four digital electric servos with a maximum deflection rate of 360°/sec. A custom code was created to allow dynamic AoA variations of the test wing with simultaneous dynamic force measurements. During the dynamic investigations, various control strategies were tested, starting from standard PID controllers with semi-empirical parameter tuning models to Direct Inverse Controllers with neural network tuning strategies and pure self-learning neural network controllers. The results of the closed-loop measurements using the manually tuned PID controller showed a reduction potential for the dynamic lift loads in the range of 70% as well as a stable controller behavior. The Direct Inverse Controller not only showed a load reduction of 36.8%, but also significant improvement potential with respect to its fine-tuning.

scholarly journals Performance Optimization of Wind Turbine Rotors with Active Flow Control (Part 2)

2012 ◽  
Vol 134 (08) ◽  
pp. 55-55 ◽  
Author(s):  
G. Pechlivanoglou ◽  
C.N. Nayeri ◽  
C.O. Paschereit
Keyword(s):  
Flow Control ◽  
Wind Turbine ◽  
Performance Optimization ◽  
System Integration ◽  
Large Scale ◽  
Active Flow Control ◽  
Lightning Strike ◽  
Scale Production ◽  
Turbine Rotors ◽  
Active Flow

This article discusses the performance optimization of wind turbine rotors with active flow control. An extensive multi-parameter investigation with a thorough matrix-grading system was performed to identify the most suitable solution for industrial quality, short/mid-term implementation on actual utility scale wind turbines. A very wide selection of aerodynamic flow control solutions was analyzed based on extensive multi-disciplinary literature review and through aerodynamic and aeroelastic simulations. It is suggested that the trailing edge devices have the most favorable performance in the field of system integration and mechanical design performance. Compliant structures like the flexible flap keep the number of moving parts to a minimum while maintaining high performance and manufacturing simplicity. The use of flexible and elastic materials based on polymers or rubber material improves the lightning strike resistance of these solutions and allows for low-cost large-scale production. The actuator principle, sensitivity, and reliability are decisive parameters, and pneumatic actuators seem to strike a good balance between performance, cost, and reliability.

Sign in / Sign up

Export Citation Format

Share Document