scholarly journals Predicting Chemical Wear in Machining Titanium Alloys Via a Novel Low Cost Diffusion Couple Method

Procedia CIRP ◽  
2016 ◽  
Vol 45 ◽  
pp. 219-222 ◽  
Author(s):  
Oliver Hatt ◽  
Henrik Larsson ◽  
Finn Giuliani ◽  
Pete Crawforth ◽  
Bradley Wynne ◽  
...  
Keyword(s):  
Diffusion Couple ◽  
Titanium Alloys ◽  
Low Cost ◽  
Couple Method

scholarly journals Design of Low-Cost and High-Strength Titanium Alloys Using Pseudo-Spinodal Mechanism through Diffusion Couple Technology and CALPHAD

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2910
Author(s):  
Chaoyi Ding ◽  
Chun Liu ◽  
Ligang Zhang ◽  
Di Wu ◽  
Libin Liu
Keyword(s):  
Diffusion Couple ◽  
Titanium Alloys ◽  
High Throughput ◽  
Volume Fraction ◽  
Raw Materials ◽  
Low Cost ◽  
High Strength ◽  
High Yield ◽  
Α Phase ◽  
Cr System

The high cost of development and raw materials have been obstacles to the widespread use of titanium alloys. In the present study, the high-throughput experimental method of diffusion couple combined with CALPHAD calculation was used to design and prepare the low-cost and high-strength Ti-Al-Cr system titanium alloy. The results showed that ultra-fine α phase was obtained in Ti-6Al-10.9Cr alloy designed through the pseudo-spinodal mechanism, and it has a high yield strength of 1437 ± 7 MPa. Furthermore, application of the 3D strength model of Ti-6Al-xCr alloy showed that the strength of the alloy depended on the volume fraction and thickness of the α phase. The large number of α/β interfaces produced by ultra-fine α phase greatly improved the strength of the alloy but limited its ductility. Thus, we have demonstrated that the pseudo-spinodal mechanism combined with high-throughput diffusion couple technology and CALPHAD was an efficient method to design low-cost and high-strength titanium alloys.

Fracture Toughness of Powder Metallurgy and Ingot Titanium Alloys – A Review

2013 ◽  
Vol 551 ◽  
pp. 143-160 ◽  
Author(s):  
Ajit Pal Singh ◽  
Brian Gabbitas ◽  
De Liang Zhang
Keyword(s):  
Fracture Toughness ◽  
Powder Metallurgy ◽  
Titanium Alloys ◽  
Alloy Composition ◽  
Low Cost ◽  
Ingot Metallurgy ◽  
Metal Powders ◽  
Critical Factors ◽  
Microstructural Characteristics ◽  
High Degree

Powder metallurgy (PM) is potentially capable of producing homogeneous titanium alloys at relative low cost compared to ingot metallurgy (IM). There are many established PM methods for consolidating metal powders to near net shapes with a high degree of freedom in alloy composition and resulting microstructural characteristics. The mechanical properties of titanium and its alloys processed using a powder metallurgical route have been studied in great detail; one major concern is that ductility and toughness of materials produced by a PM route are often lower than those of corresponding IM materials. The aim of this paper is to review the fracture toughness of both PM and IM titanium alloys. The effects of critical factors such as interstitial impurities, microstructural features and heat treatment on fracture toughness are also discussed

scholarly journals A Review on Diffusion Bonding between Titanium Alloys and Stainless Steels

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
De-feng Mo ◽  
Ting-feng Song ◽  
Yong-jian Fang ◽  
Xiao-song Jiang ◽  
Charles Q. Luo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Titanium Alloy ◽  
Titanium Alloys ◽  
Stainless Steels ◽  
Diffusion Bonding ◽  
Low Cost ◽  
Phase Interface ◽  
Intermetallic Phases ◽  
Voids Growth

High-quality joints between titanium alloys and stainless steels have found applications for nuclear, petrochemical, cryogenic, and aerospace industries due to their relatively low cost, lightweight, high corrosion resistance, and appreciable mechanical properties. This article reviews diffusion bonding between titanium alloys and stainless steels with or without interlayers. For diffusion bonding of a titanium alloy and a stainless steel without an interlayer, the optimized temperature is in the range of 800–950°C for a period of 60–120 min. Sound joint can be obtained, but brittle FeTi and Fe-Cr-Ti phases are formed at the interface. The development process of a joint mainly includes three steps: matching surface closure, growth of brittle intermetallic compounds, and formation of the Kirkendall voids. Growth kinetics of interfacial phases needs further clarification in terms of growth velocity of the reacting layer, moving speed of the phase interface, and the order for a new phase appears. The influence of Cu, Ni (or nickel alloy), and Ag interlayers on the microstructures and mechanical properties of the joints is systematically summarized. The content of FeTi and Fe-Cr-Ti phases at the interface can be declined significantly by the addition of an interlayer. Application of multi-interlayer well prevents the formation of intermetallic phases by forming solid solution at the interface, and parameters can be predicted by using a parabolic diffusion law. The selection of multi-interlayer was done based on two principles: no formation of brittle intermetallic phases and transitional physical properties between titanium alloy and stainless steel.

scholarly journals Research and Development of Low-cost Titanium Alloys

2019 ◽  
Vol 1347 ◽  
pp. 012022
Author(s):  
Shewei Xin ◽  
Jingli Zhang ◽  
Xiaonan Mao ◽  
Yongqing Zhao ◽  
Quan Hong
Keyword(s):  
Research And Development ◽  
Titanium Alloys ◽  
Low Cost

Composition dependence of tracer diffusion coefficients in Fe–Ga alloys: A case study by a tracer-diffusion couple method

2021 ◽  
Vol 203 ◽  
pp. 116446
Author(s):  
G.M. Muralikrishna ◽  
B. Tas ◽  
N. Esakkiraja ◽  
V.A. Esin ◽  
K.C. Hari Kumar ◽  
...  
Keyword(s):  
Diffusion Couple ◽  
Diffusion Coefficients ◽  
Composition Dependence ◽  
Tracer Diffusion ◽  
Tracer Diffusion Coefficients ◽  
Couple Method

scholarly journals Solid-state Reaction Studies in Al2O3–TiO2 System by Diffusion Couple Method

2017 ◽  
Vol 57 (10) ◽  
pp. 1762-1766 ◽  
Author(s):  
Jianchao Zheng ◽  
Xiaojun Hu ◽  
Zhongshan Ren ◽  
Xiangxin Xue ◽  
Kuochih Chou
Keyword(s):  
Solid State ◽  
Diffusion Couple ◽  
Solid State Reaction ◽  
Couple Method

Phase Constitution and Heat Treatment Behavior of Low Cost Ti-Mn System Alloys

2013 ◽  
Vol 551 ◽  
pp. 217-222 ◽  
Author(s):  
Masahiko Ikeda ◽  
Masato Ueda ◽  
Kaoru Imaizumi ◽  
Mitsuo Niinomi
Keyword(s):  
Heat Treatment ◽  
Titanium Alloys ◽  
Low Cost ◽  
Metallic Elements ◽  
X Ray Diffraction ◽  
Phase Constitution ◽  
Specific Strength ◽  
Good Biocompatibility ◽  
Fe Alloys ◽  
The Cost

This paper is a review of results for Ti-Mn [1], Ti-Mn-Al [2] and Ti-Mn-Fe [3] alloys that have been previously published. Titanium alloys, especially beta-type titanium alloys, have high specific strength, excellent corrosion resistance and good biocompatibility. Unfortunately, applications of titanium alloys are limited by their relatively higher cost. One reason is the use of rare and expensive metallic elements, such as vanadium and molybdenum, as a beta stabilizer. In order to reduce the cost, inexpensive and abundantly available metallic elements should be used as beta stabilizers. Manganese was adopted as a beta stabilizer because it is an abundant metallic element in the Earth’s crust and is relatively low in cost. The heat treatment behavior of Ti-Mn, Ti-Mn-Al and Ti-Mn-Fe alloys was investigated through electrical resistivity and Vickers hardness measurements, X-ray diffraction measurements to identify phase constitution, and observations using a light microscope [1], [2] and [3].

Approaches to the Design and Processing of Novel Titanium Alloys

2007 ◽  
Vol 29-30 ◽  
pp. 127-130
Author(s):  
Colleen J. Bettles ◽  
Rimma Lapovok ◽  
H.P. Ng ◽  
Dacian Tomus ◽  
Barry C. Muddle
Keyword(s):  
Titanium Alloys ◽  
High Performance ◽  
Powder Processing ◽  
Low Cost ◽  
Cost Effective ◽  
Processing Technologies ◽  
Shape Processing ◽  
New Processing ◽  
The Cost ◽  
Processing Techniques

The range of commercial titanium alloys available is currently extremely restricted, with one alloy (Ti-6Al-4V), and derivatives of it, accounting for a very large proportion of all applications. High performance alloys are costly to fabricate and limited to low-volume applications that can sustain the cost. With the emergence of new processing technologies that promise to reduce significantly the cost of production of titanium metal, especially in powder form, there is an emerging imperative for cost-effective near net shape powder processing techniques to permit the benefit of reduced metal cost to be passed on to higher-volume applications. Equally, there is a need for the design and development of new alloys that are intrinsically low-cost and lend themselves to fabrication by novel cost-effective net shape processing. The approaches that might be used to select, design and process both conventional alloys and novel alloy systems will be reviewed, with a focus on innovation in design of low-cost alloys amenable to new processing paths and increasingly tolerant of variability in composition.

Sign in / Sign up

Export Citation Format

Share Document