Capsular polysaccharide production by Neisseria meningitidis serogroup C: Optimization of process variables using response surface methodology

2006 ◽  
Vol 41 (8) ◽  
pp. 1822-1828 ◽  
Author(s):  
A.W.S. Henriques ◽  
E. Jessouroun ◽  
E.L. Lima ◽  
T.L.M. Alves
Keyword(s):  
Response Surface Methodology ◽  
Neisseria Meningitidis ◽  
Response Surface ◽  
Capsular Polysaccharide ◽  
Process Variables ◽  
Polysaccharide Production

scholarly journals Optimizing Adsorption of 17α-Ethinylestradiol from Water by Magnetic MXene Using Response Surface Methodology and Adsorption Kinetics, Isotherm, and Thermodynamics Studies

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3150
Author(s):  
Mengwei Xu ◽  
Chao Huang ◽  
Jing Lu ◽  
Zihan Wu ◽  
Xianxin Zhu ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Quadratic Model ◽  
Adsorption Efficiency ◽  
Process Variables ◽  
Adsorption Time ◽  
Initial Concentration ◽  
Independent Variables ◽  
The Impact ◽  
Adsorbent Dose

Magnetic MXene composite Fe3O4@Ti3C2 was successfully prepared and employed as 17α-ethinylestradiol (EE2) adsorbent from water solution. The response surface methodology was employed to investigate the interactive effects of adsorption parameters (adsorption time, pH of the solution, initial concentration, and the adsorbent dose) and optimize these parameters for obtaining maximum adsorption efficiency of EE2. The significance of independent variables and their interactions were tested by the analysis of variance (ANOVA) and t-test statistics. Optimization of the process variables for maximum adsorption of EE2 by Fe3O4@Ti3C2 was performed using the quadratic model. The model predicted maximum adsorption of 97.08% under the optimum conditions of the independent variables (adsorption time 6.7 h, pH of the solution 6.4, initial EE2 concentration 0.98 mg L−1, and the adsorbent dose 88.9 mg L−1) was very close to the experimental value (95.34%). pH showed the highest level of significance with the percent contribution (63.86%) as compared to other factors. The interactive influences of pH and initial concentration on EE2 adsorption efficiency were significant (p < 0.05). The goodness of fit of the model was checked by the coefficient of determination (R2) between the experimental and predicted values of the response variable. The response surface methodology successfully reflects the impact of various factors and optimized the process variables for EE2 adsorption. The kinetic adsorption data for EE2 fitted well with a pseudo-second-order model, while the equilibrium data followed Langmuir isotherms. Thermodynamic analysis indicated that the adsorption was a spontaneous and endothermic process. Therefore, Fe3O4@Ti3C2 composite present the outstanding capacity to be employed in the remediation of EE2 contaminated wastewaters.

Optimization of drying ammonium tetramolybdate by microwave heating using response surface methodology

2016 ◽  
Vol 5 (1) ◽  
Author(s):  
Libo Zhang ◽  
Wenqian Guo ◽  
Tu Hu ◽  
Jing Li ◽  
Jinhui Peng ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Microwave Heating ◽  
Microwave Drying ◽  
Process Variables ◽  
Optimum Conditions ◽  
Drying Time ◽  
Drying Temperature ◽  
Material Thickness ◽  
Rsm Technique

AbstractThe process of microwave drying ammonium tetramolybdate is studied, and the process variables of drying time, drying temperature and material thickness are considered. Experiences of microwave drying ammonium tetramolybdate have been optimized using response surface methodology (RSM) technique and a CCD design. Effects of each factor and their interactions are researched, and a quadratic polynomial model for dehydration ratio is established. As can be seen from the ANOVA, the effects of the three process variables are found to be significant in the model, and the empirical model is fit and reliable to check the dehydration ratio of ammonium tetramolybdate. The optimum conditions for drying using microwave heating are found as follows: drying temperature 67°C, drying time 9.5 min and material thickness 15 mm. The optimum dehydration ratio is 79.82% and the last molybdenum content is not <56.3%, with the relatively error of 0.64%, which indicates the success of the process optimization experiments. This research has important significance to offer optimum conditions for industrial production.

Sign in / Sign up

Export Citation Format

Share Document