Experimental investigation and constitutive modeling of uncured carbon black filled rubber at different strain rates

2019 ◽  
Vol 75 ◽  
pp. 117-126 ◽  
Author(s):  
Zhao Li ◽  
Yinlong Wang ◽  
Xu Li ◽  
Ziran Li ◽  
Yang Wang
Keyword(s):  
Experimental Investigation ◽  
Carbon Black ◽  
Constitutive Modeling ◽  
Strain Rates ◽  
Filled Rubber

DISCUSSION ABOUT THERMAL CONDUCTIVITY OF CARBON BLACK FILLED RUBBER

2015 ◽  
Vol 6 (2) ◽  
pp. 159-172 ◽  
Author(s):  
Junping Song ◽  
Lianxiang Ma ◽  
Yan He ◽  
Wei Li ◽  
Shi-Chune Yao
Keyword(s):  
Thermal Conductivity ◽  
Carbon Black ◽  
Filled Rubber

Studies on dynamic creep of carbon black-filled rubber vulcanizates.

1989 ◽  
Vol 62 (7) ◽  
pp. 448-458
Author(s):  
Kunihiko FUJIMOTO ◽  
Tatsuhiko HATAKEYAMA
Keyword(s):  
Carbon Black ◽  
Filled Rubber ◽  
Dynamic Creep

STUDY ON NANOMORPHOLOGY OF HIGH-STRUCTURE CARBON BLACK AND ITS BOUND RUBBER BY AFM

2012 ◽  
Vol 19 (01) ◽  
pp. 1250003
Author(s):  
JIAN CHEN ◽  
YONGZHONG JIN ◽  
JINGYU ZHANG ◽  
YAFENG WU ◽  
CHUNCAI MENG
Keyword(s):  
Carbon Black ◽  
Cluster Structure ◽  
Chemical Activity ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Atomic Force ◽  
Filled Rubber ◽  
Bound Rubber ◽  
Styrene Butadiene ◽  
High Structure

Bound rubber in carbon black (CB) filled rubber (natural rubber (NR) and styrene–butadiene rubber (SBS)) was prepared by the solvent method. The nanomorphology of CB and rubber/CB soluble rubber was observed by atomic force microscope. The results show that high-structure CB DZ13 has a "grape cluster" structure which consists of many original particles with the grain size of about 30–50 nm. Graphitizing process of CB decreases the amount of bound rubber. The NR/DZ13 soluble rubber with island–rim structure has been obtained, where the islands are DZ13 particles and the rims around the islands are occupied by NR film. But when the graphitized DZ13 particles were used as fillers of rubber, we have only observed that some graphitized DZ13 particles were deposited on the surface of the globular-like NR molecular chains, instead of the spreading of NR molecular chains along the surface of DZ13 particles, indicating that graphitized DZ13 has lower chemical activity than ungraphitized DZ13. Especially, we have already observed an interesting unusual bound rubber phenomenon, the blocked "bracelet" structure with the diameter of about 600 nm in which CB particles were blocked in ring-shaped SBS monomer.

States of Carbon Black Dispersion and Extensibility of Rubbers

1993 ◽  
Vol 66 (2) ◽  
pp. 317-328 ◽  
Author(s):  
Asahiro Ahagon
Keyword(s):  
Carbon Black ◽  
Tensile Property ◽  
Crosslink Density ◽  
Hydrodynamic Effect ◽  
Property Variation ◽  
Agglomerate Size ◽  
Filled Rubber ◽  
Two Temperatures ◽  
Confined Polymer ◽  
Carbon Black Dispersion

Abstract Analysis is made for the origin of the mixing-induced tensile property variation of a filled rubber. Attention is paid to the hydrodynamic effect f(ϕe) of the filler, defined here as the factor to adjust the deviation of 100% modulus from the theory of rubber elasticity. For the rubbers mixed under variety of conditions, the f(ϕe)'s are calculated from the observed values of the modulus, at 25°C and 100°C, and the crosslink density. The variation of the f(ϕe) is considered to be governed by the mobility of the polymer confined in agglomerates of the filler. The mobility variation due to mixing seems to be mainly influenced by agglomerate size at 25°C, and by agglomerate size and chemical constraints at 100°C. Therefore, the f(ϕe)'s at the two temperatures are suggested to be useful measures of the state of carbon-black micro-dispersion. The extensibility of the rubbers is closely related f(ϕe). This indicates that the failure property is also governed by the mobility of the confined polymer.

Constitutive modeling for the mechanical behavior of rubber with filler particles

2021 ◽  
Author(s):  
Sankalp Gour ◽  
Deepu Kumar Singh ◽  
Deepak Kumar ◽  
Vinod Yadav
Keyword(s):  
Mechanical Properties ◽  
Carbon Black ◽  
Mechanical Behavior ◽  
Experimental Observation ◽  
Continuum Mechanics ◽  
Constitutive Modeling ◽  
Carbon Nanoparticles ◽  
Material Behavior ◽  
Experimental Results ◽  
Filler Particles

Abstract The present study deals with the constitutive modeling for the mechanical behavior of rubber with filler particles. An analytical model is developed to predict the mechanical properties of rubber with added filler particles based on experimental observation. To develop the same, a continuum mechanics-based hyperelasticity theory is utilized. The model is validated with the experimental results of the chloroprene and nitrile butadiene rubbers filled with different volume fractions of carbon black and carbon nanoparticles, respectively. The findings of the model agree well with the experimental results. In general, the developed model will be helpful to the materialist community working in characterizing the material behavior of tires and other rubber-like materials.

Sign in / Sign up

Export Citation Format

Share Document