Influences of polymer matrix melt viscosity and molecular weight on MWCNT agglomerate dispersion

Polymer ◽  
2011 ◽  
Vol 52 (4) ◽  
pp. 1027-1036 ◽  
Author(s):  
Gaurav R. Kasaliwal ◽  
Andreas Göldel ◽  
Petra Pötschke ◽  
Gert Heinrich
Keyword(s):  
Molecular Weight ◽  
Polymer Matrix ◽  
Melt Viscosity ◽  
Agglomerate Dispersion

Investigating the Rheological Properties and Heat Stability of Polyarylsulphone Sulphides of Domestic Grades

2017 ◽  
Vol 44 (1) ◽  
pp. 23-26
Author(s):  
A.B. Baranov ◽  
I.D. Simonov-Emel'yanov ◽  
T.I. Andreeva ◽  
T.N. Prudskova ◽  
V.I. Sazikov
Keyword(s):  
Molecular Weight ◽  
Heat Stability ◽  
Chain Structure ◽  
Low Flow ◽  
Processing Temperature ◽  
Rheological Characteristics ◽  
Melt Viscosity ◽  
Full Curve ◽  
Temperature Range ◽  
Service Characteristics

The rheological characteristics of melts of polyarylsulphone sulphides of domestic grades were investigated in the temperature range 240–360°C. Full curves of heat stability were obtained, and formulae were proposed for their description. Polyarylsulphone sulphides (PSPSs) are heat-resistant polymers of structural designation of the polysulphone (PSP) class, the domestic production technology of which was developed at OAO “Institut plastmass”, which makes it possible to carry out the production of a wide grade range of PSP of different polymer chain structure and molecular weight. The main problem in the processing of PSPSs is their high melt viscosity and fairly low flow. Increase in the processing temperature lowers their melt viscosity, but there is then the danger of thermooxidative degradation of the polymer and consequently of deterioration in the service characteristics and appearance of articles. The aim of this work was to investigate the rheological characteristics and to obtain the full curve of heat stability for domestic grades of PSPSs and PSP of different molecular weight in a wide processing temperature range.

scholarly journals Polymer Nanocomposites Exploited Under The Arctic Conditions

2016 ◽  
Vol 1 (1) ◽  
pp. 122 ◽  
Author(s):  
A.A. Okhlopkova ◽  
L.A. Nikiforov ◽  
T.A. Okhlopkova ◽  
R.V. Borisova
Keyword(s):  
Molecular Weight ◽  
Mechanical Activation ◽  
High Molecular Weight ◽  
Polymer Matrix ◽  
Planetary Mill ◽  
Layered Silicates ◽  
The Arctic ◽  
Liquid Media ◽  
Arctic Conditions ◽  
Ultra High Molecular Weight

<p>Several technologies of the preparation of nanocomposites based on ultra-high-molecular-weight polyethylene were developed. The first technology is based on mechanical activation of layered silicates with surfactant before addition into polymer matrix. The second technology represents mixing of ultra-high-molecular-weight polyethylene with nanoparticles by joint mechanical activation in a planetary mill. The third technology is based on mixing of ultra-high-molecular-weight polyethylene with nanoparticles in liquid media under continuous ultrasonic treatment. Common features of these technologies are reaching of filler uniform distribution in a polymer matrix and significant improvement in the mechanical properties. Also, supramolecular structure of the composites was studied.</p>

Polystyrene–organoclay nanocomposites produced by in situ activators regenerated by electron transfer for atom transfer radical polymerization

2012 ◽  
Vol 32 (4-5) ◽  
pp. 235-243 ◽  
Author(s):  
Khezrollah Khezri ◽  
Vahid Haddadi-Asl ◽  
Hossein Roghani-Mamaqani ◽  
Mehdi Salami-Kalajahi
Keyword(s):  
Molecular Weight ◽  
Electron Transfer ◽  
Atom Transfer Radical Polymerization ◽  
Radical Polymerization ◽  
Polymer Matrix ◽  
Clay Content ◽  
Xrd Analysis ◽  
Size Exclusion ◽  
Atom Transfer ◽  
Scanning Calorimetry

Abstract A newly developed initiation system, activators regenerated by electron transfer (ARGET), was employed to synthesize polystyrene-organoclay nanocomposites via atom transfer radical polymerization (ATRP). ARGET ATRP was applied since it is carried out at significantly low concentrations of the catalyst and environmentally acceptable reducing agents. Conversion and molecular weight evaluations were performed using gravimetry and size exclusion chromatography (SEC), respectively. According to the findings, addition of clay content resulted in a decrease in conversion and molecular weight of nanocomposites. However, an increase of polydispersity index is observed by increasing nanoclay loading. The living nature of the polymerization is revealed by 1H NMR spectroscopy and extracted data from the SEC traces. X-ray diffraction (XRD) analysis shows that organoclay layers are disordered and delaminated in the polymer matrix and exfoliated morphology is obtained. Thermogravimetric analysis (TGA) shows that thermal stability of the nanocomposites is higher than the neat polystyrene. A decrease in glass transition temperature of the samples by increasing organoclay content is observed by differential scanning calorimetry (DSC). Transmission electron microscopy (TEM) reveals that clay layers are partially exfoliated in the polymer matrix containing 2 wt% of organomodified montmorillonite (PSON 2) and a dispersion of partially exfoliated clay stacks is formed.

Flow-induced structure and rheological properties of multiwall carbon nanotube/polydimethylsiloxane composites

RSC Advances ◽  
2014 ◽  
Vol 4 (107) ◽  
pp. 62759-62768 ◽  
Author(s):  
Ran Niu ◽  
Jiang Gong ◽  
Donghua Xu ◽  
Tao Tang ◽  
Zhao-Yan Sun
Keyword(s):  
Molecular Weight ◽  
Carbon Nanotube ◽  
Rheological Properties ◽  
Normal Stress ◽  
Polymer Composites ◽  
Polymer Matrix ◽  
Multiwall Carbon Nanotube ◽  
Normal Stress Differences ◽  
Induced Structure ◽  
Multiwall Carbon

The structure and normal stress differences of MWNT/polymer composites are influenced by the molecular weight of the polymer matrix and the confinement effect.

Sign in / Sign up

Export Citation Format

Share Document