Investigations of temperature dependences of electrical resistivity and specific heat capacity of metals

2016 ◽  
Vol 492 ◽  
pp. 7-10 ◽  
Author(s):  
Erhan Eser ◽  
Hüseyin Koç
Keyword(s):  
Heat Capacity ◽  
Electrical Resistivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Temperature Dependences

scholarly journals MAGNETOCALORIC EFFECT AND HEAT CAPACITY OF MAGNETIC FLUIDS

2020 ◽  
Vol 63 (5) ◽  
pp. 12-18
Author(s):  
Viktor V. Korolev ◽  
Anna G. Ramazanova ◽  
Olga V. Balmasova ◽  
Matvey S. Gruzdev
Keyword(s):  
Magnetic Field ◽  
Heat Capacity ◽  
Magnetic Fields ◽  
Specific Heat ◽  
Magnetocaloric Effect ◽  
Specific Heat Capacity ◽  
Magnetic Fluids ◽  
Zero Magnetic Field ◽  
Extreme Character ◽  
Temperature Dependences

The magnetic fluids based on magnetite nanoparticles were synthesized using mixed surfactants (oleic acid/alkenyl succinic anhydride) dispersed in different carrier media (polyethylsiloxane and dialkyldiphenyl). The physicochemical properties of magnetic fluids (density, viscosity, saturation magnetization, magnetic phase concentration, magnetic core size) were determined. Magnetic fluids are stable in a wide temperature range. All the samples of the magnetic fluids exhibit typical superparamagnetic behavior. The magnetocaloric effect and the specific heat capacity of the magnetic fluids were first direct determined at 288–350 K in a magnetic field of 0–1.0 T. The field dependences of the magnetocaloric effect have a classic linear form. The temperature dependences of the magnetocaloric effect of magnetic fluids in magnetic fields have an extreme character. Thermodynamic parameters of magnetic fluids (magnetization namely enthalpy/entropy change) were determined. The specific heat capacity of magnetic fluid samples in a zero magnetic field was obtained at different temperatures (at 278–350 K) on a differential scanning calorimeter and on the original microcalorimeter. The temperature dependences of the heat capacity of magnetic fluids in magnetic fields have an extreme character. It was established that the difference in heat capacity values obtained in and without the magnetic field is within the experimental error. The extreme character of the heat capacity is reflected in the magnetocaloric effect temperature dependences.

scholarly journals Software solution for control and data acquisition in the pulse calorimetry method

2013 ◽  
Vol 10 (1) ◽  
pp. 13-21 ◽  
Author(s):  
Marijana Babic ◽  
Nenad Milosevic ◽  
Nenad Stepanic
Keyword(s):  
Heat Capacity ◽  
Electrical Resistivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Spectral Emissivity ◽  
Normal Spectral Emissivity ◽  
Measurement Results ◽  
Labview Platform ◽  
Total Hemispherical Emissivity ◽  
Emissivity Measurements

This work presents a software solution for adjusting, controlling, displaying, and acquiring parameters and data in the pulse calorimetry experimental technique for specific heat capacity, electrical resistivity, total hemispherical emissivity, and normal spectral emissivity measurements. The software has been developed under the LabVIEW platform, V.7.11, and an example of its application with measurement results is presented in a separate section. The total expanded uncertainty of obtained results for the specific heat capacity and electrical resistivity of palladium was 5% and 1 - 2%, respectively.

Теплофизические характеристики теплозащитного материала корпуса ракетного двигателя при температурах до 1000 оС

2021 ◽  
pp. 11-18
Author(s):  
Геннадий Александрович Фролов ◽  
Юрий Игоревич Евдокименко ◽  
Вячеслав Михайлович Кисель ◽  
Ирина Александровна Гусарова
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Temperature Fields ◽  
Thermophysical Characteristics ◽  
Furnace Heating ◽  
Temperature Dependences ◽  
Good Agreement

An experimental determination of the temperature dependences of the specific heat capacity and the thermal conductivity coefficient of the multifunctional coating MFP-92 at temperatures up to 1000 °C has been carried out. At temperatures up to 450 °C, an IT-c-400 device was used to determine the specific heat capacity. IT-l-400 device was used for the determination of thermal conductivity. At higher temperatures, the determination of the thermophysical characteristics (TPC) was carried out by solving the inverse problem of thermal conductivity (IPT) in a flat plate under conditions of one-sided heating in a muffle furnace. Composite material MFP-92 is a multilayer structure with upper layers based on silica fabric and chromophosphate binder and lower layers based on mullite-silica fabric and aluminosilicate binder. The TPC of the layers also differ from each other, and, accordingly, the properties of this material as a whole can be determined only in the form of their effective values, averaged in one way or another over the thickness of the coating. In addition, during heating, the material undergoes significant physicochemical transformations associated with the thermal destruction of its components, manifested in the form of abundant gas release, and a decrease in the density of the material, which significantly changes its TPC and determines its dependence on the heating rate. Therefore, studies of the thermophysical characteristics of the MFP-92 material were carried out with several (2-5) consecutive heating cycles. It was found that in four heating cycles of the MFP-92 material up to 450 °C for 75 minutes when measuring the specific heat on the IT-c-400 device, its temperature dependence significantly changes qualitatively and quantitatively. With furnace heating to 1000 °C, the temperature dependences of the TPC of the material, determined in the first and second heating cycles, have a different form, but change insignificantly in subsequent heating cycles. This makes it possible to ascribe to the MFP-92 material a set of two sets of TPC related to its initial (phase A) and annealed after heating to 1000 °C (phase B) states. Using the obtained TPС of phase A (including the magnitude of the thermal effect of irreversible endothermic phase transition at 100 °C) and phase B, good agreement was obtained between the calculated and experimental temperature fields in the samples under furnace heating conditions.

Experimental Study on the Specific Heat Capacity Measurement of Water-Based Al2O3-Cu Hybrid Nanofluid by using Differential Thermal Analysis Method

2019 ◽  
Vol 15 ◽  
Author(s):  
Andaç Batur Çolak ◽  
Oğuzhan Yıldız ◽  
Mustafa Bayrak ◽  
Ali Celen ◽  
Ahmet Selim Dalkılıç ◽  
...  
Keyword(s):  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Thermophysical Properties ◽  
Volume Concentration ◽  
Pure Water ◽  
Heat Capacity Measurement ◽  
Experimental Results ◽  
Hybrid Nanofluid ◽  
Capacity Measurement

Background: Researchers working in the field of nanofluid have done many studies on the thermophysical properties of nanofluids. Among these studies, the number of studies on specific heat are rather limited. In the study of the heat transfer performance of nanofluids, it is necessary to increase the number of specific heat studies, whose subject is one of the important thermophysical properties. Objective: The authors aimed to measure the specific heat values of Al2O3/water, Cu/water nanofluids and Al2O3-Cu/water hybrid nanofluids using the DTA method, and compare the results with those frequently used in the literature. In addition, this study focuses on the effect of temperature and volume concentration on specific heat. Method: The two-step method was used in the preparation of nanofluids. The pure water selected as the base fluid was mixed with the Al2O3 and Cu nanoparticles and Arabic Gum as the surfactant, firstly mixed in the magnetic stirrer for half an hour. It was then homogenized for 6 hours in the ultrasonic homogenizer. Results: After the experiments, the specific heat of nanofluids and hybrid nanofluid were compared and the temperature and volume concentration of specific heat were investigated. Then, the experimental results obtained for all three fluids were compared with the two frequently used correlations in the literature. Conclusion: Specific heat capacity increased with increasing temperature, and decreased with increasing volume concentration for three tested nanofluids. Cu/water has the lowest specific heat capacity among all tested fluids. Experimental specific heat capacity measurement results are compared by using the models developed by Pak and Cho and Xuan and Roetzel. According to experimental results, these correlations can predict experimental results within the range of ±1%.

Development of the room temperature protocol based on room temperature ionic liquids and surfactant ionic liquids for the synthesis of derivatives of 2-amino-thiazoles and thermo-physical analysis of the synthesized derivatives using TGA-DSC.

2020 ◽  
Vol 10 ◽  
Author(s):  
Chandrakant Sarode ◽  
Sachin Yeole ◽  
Ganesh Chaudhari ◽  
Govinda Waghulde ◽  
Gaurav Gupta
Keyword(s):  
Thermal Analysis ◽  
Heat Capacity ◽  
Ionic Liquids ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Room Temperature ◽  
Heat Capacity Data ◽  
General Strategy ◽  
Capacity Data ◽  
Derivatives Of

Aims: To develop an efficient protocol, which involves an elegant exploration of the catalytic potential of both the room temperature and surfactant ionic liquids towards the synthesis of biologically important derivatives of 2-aminothiazole. Objective: Specific heat capacity data as a function of temperature for the synthesized 2- aminothiazole derivatives has been advanced by exploring their thermal profiles. Method: The thermal gravimetry analysis and differential scanning calorimetry techniques are used systematically. Results: The present strategy could prove to be a useful general strategy for researchers working in the field of surfactants and surfactant based ionic liquids towards their exploration in organic synthesis. In addition to that, effect of electronic parameters on the melting temperature of the corresponding 2-aminothiazole has been demonstrated with the help of thermal analysis. Specific heat capacity data as a function of temperature for the synthesized 2-aminothiazole derivatives has also been reported. Conclusion: Melting behavior of the synthesized 2-aminothiazole derivatives is to be described on the basis of electronic effects with the help of thermal analysis. Additionally, the specific heat capacity data can be helpful to the chemists, those are engaged in chemical modelling as well as docking studies. Furthermore, the data also helps to determine valuable thermodynamic parameters such as entropy and enthalpy.

scholarly journals Influence of alkaline modification on selected properties of banana fiber paperbricks

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Abayomi A. Akinwande ◽  
Adeolu A. Adediran ◽  
Oluwatosin A. Balogun ◽  
Oluwaseyi S. Olusoju ◽  
Olanrewaju S. Adesina
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Moisture Absorption ◽  
Water Volume ◽  
Banana Fiber ◽  
Fiber Loading ◽  
Banana Fibers ◽  
Alkaline Modification

AbstractIn a bid to develop paper bricks as alternative masonry units, unmodified banana fibers (UMBF) and alkaline (1 Molar aqueous sodium hydroxide) modified banana fibers (AMBF), fine sand, and ordinary Portland cement were blended with waste paper pulp. The fibers were introduced in varying proportions of 0, 0.5, 1.0 1.5, 2.0, and 2.5 wt% (by weight of the pulp) and curing was done for 28 and 56 days. Properties such as water and moisture absorption, compressive, flexural, and splitting tensile strengths, thermal conductivity, and specific heat capacity were appraised. The outcome of the examinations carried out revealed that water absorption rose with fiber loading while AMBF reinforced samples absorbed lesser water volume than UMBF reinforced samples; a feat occasioned by alkaline treatment of banana fiber. Moisture absorption increased with paper bricks doped with UMBF, while in the case of AMBF-paper bricks, property value was noted to depreciate with increment in AMBF proportion. Fiber loading resulted in improvement of compressive, flexural, and splitting tensile strengths and it was noted that AMBF reinforced samples performed better. The result of the thermal test showed that incorporation of UMBF led to depreciation in thermal conductivity while AMBF infusion in the bricks initiated increment in value. Opposite behaviour was observed for specific heat capacity as UMBF enhanced heat capacity while AMBF led to depreciation. Experimental trend analysis carried out indicates that curing length and alkaline modification of fiber were effective in maximizing the properties of paperbricks for masonry construction.

scholarly journals Effects of SiO2 Nanoparticle Dispersion on The Heat Storage Property of the Solar Salt for Solar Power Applications

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 703
Author(s):  
Zhao Li ◽  
Liu Cui ◽  
Baorang Li ◽  
Xiaoze Du
Keyword(s):  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Heat Storage ◽  
Md Simulations ◽  
Interfacial Thermal Resistance ◽  
Solar Salt ◽  
Salt Ions ◽  
Base Salt ◽  
Storage Property

The effects of SiO2 nanoparticles on the heat storage properties of Solar Salt (NaNO3-KNO3) are studied using experimental and molecular dynamics (MD) simulations. The experiment results show the specific heat capacity of the molten salt-based nanofluids is higher than that of the pure base salt. We focus on the inference regarding the possible mechanisms behind the enhancement of the specific heat capacity which are considered more acceptable by the majority of researchers, the energy and force in the system are analyzed by MD simulations. The results demonstrate that the higher specific heat capacity of the nanoparticle is not the reason leading to the heat storage enhancement. Additionally, the analysis of potential energy and system configuration shows that the other possible mechanisms (i.e., interfacial thermal resistance theory and compressed layer theory) are only superficial. The forces between the nanoparticle atoms and base salt ions construct the constraint of the base salt ions, further forms the interfacial thermal resistance, and the compressed layer around the nanoparticle. This constraint has a more stable state and requires more energy to deform it, leading to the improvement of the heat storage property of nanofluids. Our findings uncover the mechanisms of specific heat capacity enhancement and guide the preparation of molten salt-based nanofluids.

Sign in / Sign up

Export Citation Format

Share Document