scholarly journals Focused ion beam fabrication and IBIC characterization of a diamond detector with buried electrodes

2011 ◽  
Vol 269 (20) ◽  
pp. 2340-2344 ◽  
Author(s):  
P. Olivero ◽  
J. Forneris ◽  
M. Jakšić ◽  
Ž. Pastuović ◽  
F. Picollo ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Diamond Detector

Electrical Characterization of Different Failure Modes in Sub-100 nm Devices Using Nanoprobing Technique

2009 ◽  
Author(s):  
E. Hendarto ◽  
S.L. Toh ◽  
J. Sudijono ◽  
P.K. Tan ◽  
H. Tan ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Nickel Silicide ◽  
Fault Isolation ◽  
Technology Nodes ◽  
Scanning Electron

Abstract The scanning electron microscope (SEM) based nanoprobing technique has established itself as an indispensable failure analysis (FA) technique as technology nodes continue to shrink according to Moore's Law. Although it has its share of disadvantages, SEM-based nanoprobing is often preferred because of its advantages over other FA techniques such as focused ion beam in fault isolation. This paper presents the effectiveness of the nanoprobing technique in isolating nanoscale defects in three different cases in sub-100 nm devices: soft-fail defect caused by asymmetrical nickel silicide (NiSi) formation, hard-fail defect caused by abnormal NiSi formation leading to contact-poly short, and isolation of resistive contact in a large electrical test structure. Results suggest that the SEM based nanoprobing technique is particularly useful in identifying causes of soft-fails and plays a very important role in investigating the cause of hard-fails and improving device yield.

Physical Failure Analysis Techniques for Front-End-of-Line Defect Analysis

2016 ◽  
Author(s):  
Dirk Doyle ◽  
Lawrence Benedict ◽  
Fritz Christian Awitan
Keyword(s):  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Gate Oxide ◽  
Top Down ◽  
New Techniques ◽  
First Case ◽  
Transmission Electron ◽  
Scanning Transmission

Abstract Novel techniques to expose substrate-level defects are presented in this paper. New techniques such as inter-layer dielectric (ILD) thinning, high keV imaging, and XeF2 poly etch overflow are introduced. We describe these techniques as applied to two different defects types at FEOL. In the first case, by using ILD thinning and high keV imaging, coupled with focused ion beam (FIB) cross section and scanning transmission electron microscopy (STEM,) we were able to judge where to sample for TEM from a top down perspective while simultaneously providing the top down images giving both perspectives on the same sample. In the second case we show retention of the poly Si short after removal of CoSi2 formation on poly. Removal of the CoSi2 exposes the poly Si such that we can utilize XeF2 to remove poly without damaging gate oxide to reveal pinhole defects in the gate oxide. Overall, using these techniques have led to 1) increased chances of successfully finding the defects, 2) better characterization of the defects by having a planar view perspective and 3) reduced time in localizing defects compared to performing cross section alone.

Optimized screen-printing and SEM-FIB characterization of YSZ thin films for Solid Oxide Fuel Cells and gas sensors devices

2004 ◽  
Vol 822 ◽  
Author(s):  
A. Morata ◽  
A. Tarancón ◽  
G. Dezanneau ◽  
F. Peiró ◽  
J. R. Morante
Keyword(s):  
Experimental Design ◽  
Screen Printing ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Deposition Process ◽  
Technological Parameters ◽  
Significant Information ◽  
Screen Printing Technique ◽  
Final Porosity

AbstractIn the present work, the screen printing technique has been used to deposit thick films of Zr0.84Y016O1.92 (8YSZ). In order to control the final porosity in view of a specific application (SOFCs or gas sensor), an experimental design based on analysis of variances (ANOVA) has been carried out. From this, we were able to determine the influence of several technological parameters on films porosity and grain size. The films obtained have been analysed with both Scanning Electron Microscopy (SEM) and Focused Ion Beam (FIB) combined with SEM. We show that only the combination of experimental design and advanced observation technique such as Focused Ion Beam allowed us to extract significant information for the improvement of the deposition process.

Fabrication of Ga-templates Using a Focused Ion Beam

2009 ◽  
Vol 1228 ◽  
Author(s):  
Hao Wang ◽  
Greg C. Hartman ◽  
Joshua Williams ◽  
Jennifer L. Gray
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Processing Conditions ◽  
New Materials ◽  
Force Microscopy ◽  
Atomic Force ◽  
Nitridation Process ◽  
Microscopy Characterization ◽  
Device Technology

AbstractThere are many factors that have the potential to limit significant advances in device technology. These include the ability to arrange materials at shrinking dimensions and the ability to successfully integrate new materials with better properties or new functionalities. To overcome these limitations, the development of advanced processing methods that can organize various combinations of materials at nano-scale dimensions with the necessary quality and reliability is required. We have explored using a gallium focused ion beam (FIB) as a method of integrating highly mismatched materials with silicon by creating template patterns directly on Si with nanoscale resolution. These templates are potentially useful as a means of locally controlling topography at nanoscale dimensions or as a means of locally implanting Ga at specific surface sites. We have annealed these templates in vacuum to study the effects of ion dosage on local Ga concentration and topography. We have also investigated the feasibility of creating Ga nanodots using this method that could eventually be converted to GaN through a nitridation process. Atomic force microscopy and electron microscopy characterization of the resulting structures are shown for a variety of patterning and processing conditions.

scholarly journals Electrical and Chemical Characterization of FIB-Deposited Insulators

1997 ◽  
Author(s):  
A. N. Campbell ◽  
D. M. Tanner ◽  
J. M. Soden ◽  
D. K. Stewart ◽  
A. Doyle ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Rutherford Backscattering Spectrometry ◽  
Ion Beam ◽  
Chemical Properties ◽  
Chemical Characterization ◽  
Breakdown Field ◽  
Gate Oxides ◽  
Spectrometry Analysis ◽  
Metal Insulator Metal

Abstract The electrical and chemical properties of insulators produced by codeposition of siloxane compounds or TEOS with oxygen in a focused ion beam (FIB) system were investigated. Metal-insulator-metal capacitor structures were fabricated and tested. Specifically, leakage current and breakdown voltage were measured and used to calculate the effective resistance and breakdown field. Capacitance measurements were performed on a subset of the structures. It was found that the siloxanebased FIB-insulators had superior electrical properties to those based on TEOS. Microbeam Rutherford backscattering spectrometry analysis and Fourier transform infrared spectroscopy were used to characterize the films and to help understand the differences in electrical behavior as a function of gas chemistry and deposition conditions. Finally, a comparison is made between the results presented here, previous results for FIB-deposited insulators, and typical thermally-grown gate oxides and interlevel dielectric Si02 insulators.

Sign in / Sign up

Export Citation Format

Share Document