scholarly journals Design response spectra-compliant real and synthetic GMS for seismic analysis of seismically isolated nuclear reactor containment building

2017 ◽  
Vol 49 (4) ◽  
pp. 825-837 ◽  
Author(s):  
Ahmer Ali ◽  
Nadin Abu-Hayah ◽  
Dookie Kim ◽  
Sung Gook Cho
Keyword(s):  
Nuclear Reactor ◽  
Seismic Analysis ◽  
Response Spectra ◽  
Seismically Isolated

Seismic Response of Reactor Vessel Internals in the IRIS Reactor

2006 ◽  
Author(s):  
D. Aquaro ◽  
M. D. Carelli ◽  
G. Forasassi ◽  
R. Lo Frano ◽  
N. Zaccari
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Seismic Analysis ◽  
Numerical Models ◽  
Response Spectra ◽  
Reactor Vessel ◽  
Dynamic Loads ◽  
Medium Size ◽  
Set Up

The intent of this paper is the presentation and discussion of a methodology for the evaluation and analysis of seismic loads effects on a nuclear power plant. To help in focussing the presented methodology, a preliminary simplified analysis of an integral, medium size next generation PWR reactor structure (IRIS project, an integral configuration PWR under study by an international group) was considered as an application example also for models/codes evaluation. The performed preliminary seismic analysis, even though by no means complete, is intended to evaluate the method of calculating the effects of dynamic loads propagation to the reactor internals for structural design as well as geometrical and functional optimisation purposes. To this goal, finite element method and separated (sub) structures approaches were employed for studying the overall dynamic behaviour of the nuclear reactor vessel. The analysis was set up by means of numerical models, implemented on the MARC FEM code, on the basis of Design Response Spectra as indicated on the relevant rules for Nuclear Power Plants (NRC 1.60) design. The seismic analysis is indented to evaluate the dynamic loads propagated from the ground through the Containment System and Vessel to the Steam Generator’s tubes.

A Numerical Study on the Seismic Site Response of Rocky Valleys with Irregular Topographic Conditions

2019 ◽  
Vol 10 (04) ◽  
pp. 1850011 ◽  
Author(s):  
Mohammad Katebi ◽  
Behrouz Gatmiri ◽  
Pooneh Maghoul
Keyword(s):  
Seismic Analysis ◽  
Numerical Study ◽  
Site Response ◽  
Slope Angle ◽  
Response Spectra ◽  
Topographic Effects ◽  
Combined Effects ◽  
Acceleration Response ◽  
Vertically Propagating ◽  
Maximum Amplification

This paper investigates topographic effects of rocky valleys with irregular topographic conditions subjected to vertically propagating SV waves of Ricker type using a boundary element code. Valleys with two intersecting slopes, [Formula: see text] and [Formula: see text], are modelled in order to study their combined effects on ground motion. Presented in the form of pseudo-acceleration response spectra, results of this work can be extended to similar topographies. The main findings are: (i) [Formula: see text] (the first slope angle) and [Formula: see text] (L is the half width of the valley and [Formula: see text] is its corresponding height) have amplifying effects, and [Formula: see text] (the second slope angle) has de-amplifying effects on the site response. (ii) [Formula: see text] has a straight effect on intensifying the effects of both [Formula: see text] and [Formula: see text]. (iii) The combined effects of slope angles have been found to be important in modifying the response so more than a single slope should be considered for seismic analysis. (iv) Engineers should use the maximum amplification of 2.4 in case of valleys with the first and second slope angles below [Formula: see text].

Seismic Analysis of High Pier Three-Span Continuous Bridge

2015 ◽  
Vol 744-746 ◽  
pp. 890-893
Author(s):  
Xun Wu ◽  
Yong Lan Zhang
Keyword(s):  
Seismic Analysis ◽  
Linear Time ◽  
Time History ◽  
Response Spectra ◽  
Elastic Response ◽  
Modeling And Analysis ◽  
Continuous Beam Bridge ◽  
Comparison Results ◽  
Elastic Response Spectra ◽  
Nonlinear Time History

In this paper, SAP2000 and ANSYS software are used to modeling and analysis athree-span continuous beam bridge with high piers case study.By using differentbearing types and combinations to form different options, create two finiteelement models.Analysis dynamic characteristics ,elastic response spectra,linear time history and nonlinear time history .And focus on comparing dynamiccharacteristics of the earthquake response of the two programs .Running outputdata processing and comparison results show that the application of thedifferent parameters of the rational combination of rubber bearing basin bridgearrangement has better seismic performance.

Direct generation of floor design spectra (FDS) from uniform hazard spectra (UHS) — Part I: formulation of the method

2020 ◽  
Vol 47 (12) ◽  
pp. 1372-1386 ◽  
Author(s):  
Amin Asgarian ◽  
Ghyslaine McClure
Keyword(s):  
Seismic Analysis ◽  
Three Dimensional ◽  
Response Spectra ◽  
Ambient Vibration ◽  
Uniform Hazard Spectra ◽  
Design Spectra ◽  
Floor Response Spectra ◽  
Response Amplification ◽  
Direct Generation ◽  
Ambient Vibration Measurements

In most current building codes, seismic design of non-structural components (NSCs) is addressed through empirical equations that do not capture NSC response amplification due to tuning effects with higher and torsional modes of buildings and that neglect NSC damping. This work addresses these shortcomings and proposes a practical approach to generate acceleration NSC floor design spectra (FDS) in buildings directly from their corresponding uniform hazard spectra (UHS). The study is based on the linear seismic analysis of 27 reinforced concrete buildings located in Montréal, Canada, for which ambient vibration measurements (AVM) are used to determine their in situ three-dimensional dynamic characteristics. Pseudo acceleration floor response spectra (PA-FRS) are derived at every building floor for four different NSCs damping ratios. The calculated roof FRS are compared with the 5% damped UHS and a formulation is proposed to generate roof FDS for NSCs with 5% damping directly from the UHS.

Development of Target Power Spectral Density Functions Compatible With Design Response Spectra

2015 ◽  
Author(s):  
Jinsuo R. Nie ◽  
Jim Xu ◽  
Joseph I. Braverman
Keyword(s):  
Spectral Density ◽  
Power Spectral Density ◽  
Seismic Analysis ◽  
General Procedure ◽  
Response Spectra ◽  
Acceleration Time ◽  
Power Spectral ◽  
Acceleration Time Histories ◽  
Time Histories ◽  
Spectral Shapes

For seismic analysis of nuclear structures, synthetic acceleration time histories are often required and are generated to envelop design response spectra following the U.S. Nuclear Regulatory Commission, Standard Review Plan (SRP) Section 3.7.1. It has been recognized that without an additional check of the power spectral density (PSD) functions, spectral matching alone may not ensure that synthetic acceleration time histories have adequate power over the frequency range of interest. The SRP Section 3.7.1 Appendix A provides a target PSD function for the Regulatory Guide 1.60 horizontal spectral shape. For other spectral shapes, additional guidance on developing the target PSD functions compatible with the design spectra is desired. This paper presents a general procedure for the development of target PSD functions for any practical design response spectral shapes, which has been incorporated into the recent SRP 3.7.1, Revision 4.

Studies on Dynamic Characteristics of a Typical Model of Asymmetric Continuous Rigid-Frame Bridge under Different Ratio of Middle Span to Side Span

2012 ◽  
Vol 226-228 ◽  
pp. 1543-1546
Author(s):  
Tian Liang ◽  
Jun Dong ◽  
Xue Jian Xiang
Keyword(s):  
Dynamic Characteristics ◽  
Seismic Analysis ◽  
Response Spectra ◽  
Guizhou Province ◽  
Western China ◽  
Continuous Rigid Frame Bridge ◽  
Rigid Frame ◽  
Key Features ◽  
Rigid Frame Bridge ◽  
Typical Model

Due to the limit of complicated landform in western China, a typical continuous rigid-frame bridge could be easy to be built, especially for asymmetric spans. Based on the engineering background of Sinan Yantou river Bridge in Guizhou province, dynamic characteristics of the type of bridge are studied in this paper. Firstly, by using Midas/Civil, 6 different models are established and their modal analysis could be done while it is considered that the beam of left T-shaped is gradually decreasing under the same height of piers. Then, all seismic responses are calculated by using response spectra method. Finally, the computational results are discussed and some key features are summarized. Our investigation will have some valuable references for seismic analysis of the same style bridge.

DAMAGE EVOLUTION SPECTRA FOR SEISMIC ANALYSIS OF HIGH-RISE BUILDINGS

2012 ◽  
Vol 06 (03) ◽  
pp. 1250021
Author(s):  
Y. B. HO ◽  
J. S. KUANG
Keyword(s):  
Damage Evolution ◽  
Seismic Analysis ◽  
Ground Motions ◽  
Time History ◽  
Tall Buildings ◽  
Response Spectra ◽  
Seismic Damage ◽  
Analysis And Design ◽  
High Rise ◽  
Earthquake Ground Motions

Seismic response spectra are amongst one of the most important tools for characterizing earthquake ground motions. In design practice, the response spectra are presented without including any load history, hence the nonlinear analysis of structures based solely on conventional earthquake response spectra is theoretically unsound, particularly for long-period or vertically irregular high-rise buildings. In this paper, a concept of seismic damage evolution is introduced and the method of analysis for characterizing the process of seismic damage to structures under earthquakes is presented. Seismic damage evolution spectra for analysis and design of high-rise buildings are then developed as an effective means of describing and simplifying earthquake ground motions. These spectra are shown to be very useful in selecting the ground motion-time history and, particularly, validating the equivalent static-load analysis and design of high-rise buildings under near-fault pulse-like ground motions. Case studies of the seismic inelastic performance of two vertically irregular, tall buildings are presented considering the seismic damage evolution spectra.

scholarly journals Dynamic seismic analysis of nuclear power plant buildings and bearing stratum

2021 ◽  
Vol 31 (4) ◽  
pp. 79-88
Author(s):  
S. V. Koval ◽  
A. V. Kuzminov ◽  
P. A. Rodin ◽  
N. M. Sidorov
Keyword(s):  
Power Plant ◽  
Nuclear Power ◽  
Seismic Analysis ◽  
Seismic Loading ◽  
Response Spectra ◽  
Kinematic Parameters ◽  
Specialized Software ◽  
Floor Response Spectra ◽  
Calculation Results ◽  
Supporting Frame

Various approaches are used for simulating seismic loading and collaboration of a structure and a bearing stratum when carrying out dynamic seismic analysis in specialized software. In the present work, the kinematic parameters of various structures and bearing stratum were calculated using SCAD and STAR_T software. Seismic performance of a reference tower type supporting frame was calculated for 7 grade earthquake. As a result, the floor accelerograms were calculated, and the floor response spectra were built. The calculation results obtained by various methods and structure models were analyzed and compared.

Seismic Analysis Approach Applied to a Small Size Next Generation Nuclear Reactor

2008 ◽  
Author(s):  
G. Forasassi ◽  
R. Lo Frano
Keyword(s):  
Nuclear Power ◽  
Nuclear Reactor ◽  
Seismic Analysis ◽  
Methodological Approach ◽  
Free Field ◽  
Time History ◽  
Future Generation ◽  
Energy System ◽  
Ground Acceleration ◽  
Input Motion

The aim of the paper is to evaluate the behaviour of a Near Term nuclear energy system example with reference to IRIS (International Reactor Innovative and Safety) project. As it is well known the development of new and future-generation nuclear power plant (Gen IV NPP) is strictly related to the sustainability, safety and reliability as well as to the proliferation resistance. In this paper, the safety aspects related to the effects of a severe earthquake (Safe Shutdown Earthquake) as well as to the induced loads are treated by means the Substructure and Time History Approaches, assuming a free field Peak Ground Acceleration equal to 0.3 g as input motion. The analyses and upgrading of the geometry structures with highest probability of criticality are performed on rather complex and detailed 3D finite element (FE) models. The main goals were: the evaluation of the dynamic characteristics of each considered structure, the verification of the load bearing structures in order to obtain a preliminary assessment of the adopted methodological approach and structural models. The analyses results and dynamic response of internal components (e.g. Nuclear Buildings, etc.) seem to confirm the possibility to upgrade the geometry and the performances of the proposed design choices.

Sign in / Sign up

Export Citation Format

Share Document