Thermal stress concentration factors for defects in plated-through-vias

2008 ◽  
Vol 48 (2) ◽  
pp. 225-244 ◽  
Author(s):  
O. Belashov ◽  
J.K. Spelt
Keyword(s):  
Thermal Stress ◽  
Stress Concentration ◽  
Thermal Stress Concentration ◽  
Concentration Factors ◽  
Stress Concentration Factors

scholarly journals Stress Concentration Factors for Welded Plate T-Joints Subjected to Tensile, Bending and Shearing Loads

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 546
Author(s):  
Krzysztof L. Molski ◽  
Piotr Tarasiuk
Keyword(s):  
Stress Concentration ◽  
Plate Thickness ◽  
Percentage Error ◽  
Geometrical Parameters ◽  
T Joints ◽  
Loading Mode ◽  
Weld Toe ◽  
Concentration Factors ◽  
Parametric Expression ◽  
Stress Concentration Factors

The paper deals with the problem of stress concentration at the weld toe of a plate T-joint subjected to axial, bending, and shearing loading modes. Theoretical stress concentration factors were obtained from numerical simulations using the finite element method for several thousand geometrical cases, where five of the most important geometrical parameters of the joint were considered to be independent variables. For each loading mode—axial, bending, and shearing—highly accurate closed form parametric expression has been derived with a maximum percentage error lower than 2% with respect to the numerical values. Validity of each approximating formula covers the range of dimensional proportions of welded plate T-joints used in engineering applications. Two limiting cases are also included in the solutions—when the weld toe radius tends to zero and the main plate thickness becomes infinite.

Stress Analysis of Holes in Thick Plates

2004 ◽  
Vol 1-2 ◽  
pp. 153-158 ◽  
Author(s):  
S. Quinn ◽  
Janice M. Dulieu-Barton
Keyword(s):  
Stress Concentration ◽  
Stress Analysis ◽  
Uniaxial Tension ◽  
Plane Stress ◽  
Plate Surface ◽  
Flat Plates ◽  
Thick Plates ◽  
Concentration Factors ◽  
Stress Concentration Factors

A review of the Stress Concentration Factors (SCFs) obtained from normal and oblique holes in thick flat plates loaded in uniaxial tension has been conducted. The review focuses on values from the plate surface and discusses the ramifications of making a plane stress assumption.

Stress concentration factors for the torsion of curved beams of arbitrary cross-section

2006 ◽  
Vol 220 (12) ◽  
pp. 1709-1726 ◽  
Author(s):  
R E Cornwell
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Cross Section ◽  
Cross Sections ◽  
Shear Stresses ◽  
Curved Beams ◽  
Finite Element Implementation ◽  
Out Of Plane ◽  
Concentration Factors ◽  
Stress Concentration Factors

There are numerous situations in machine component design in which curved beams with cross-sections of arbitrary geometry are loaded in the plane of curvature, i.e. in flexure. However, there is little guidance in the technical literature concerning how the shear stresses resulting from out-of-plane loading of these same components are effected by the component's curvature. The current literature on out-of-plane loading of curved members relates almost exclusively to the circular and rectangular cross-sections used in springs. This article extends the range of applicability of stress concentration factors for curved beams with circular and rectangular cross-sections and greatly expands the types of cross-sections for which stress concentration factors are available. Wahl's stress concentration factor for circular cross-sections, usually assumed only valid for spring indices above 3.0, is shown to be applicable for spring indices as low as 1.2. The theory applicable to the torsion of curved beams and its finite-element implementation are outlined. Results developed using the finite-element implementation agree with previously available data for circular and rectangular cross-sections while providing stress concentration factors for a wider variety of cross-section geometries and spring indices.

Analysis of Stress Concentrations in Thick Cylinders With Sideholes and Crossholes

1972 ◽  
Vol 94 (3) ◽  
pp. 815-824 ◽  
Author(s):  
J. C. Gerdeen
Keyword(s):  
Stress Concentration ◽  
Stress Concentrations ◽  
Concentration Factors ◽  
Stress Concentration Factors ◽  
Experimental Values ◽  
Pressure Stress ◽  
Shrink Fit ◽  
Outside Diameter ◽  
Theoretical Results

An approximate theoretical analysis is presented for the determination of stress concentration factors in thick walled cylinders with sideholes and crossholes. The cylinders are subjected to both internal pressure and external shrink-fit pressure. Stress concentration factors are plotted as functions of the geometrical ratios of outside diameter-to-bore diameter, and bore diameter-to-sidehole diameter. Theoretical results are compared to experimental values available in the literature and results of experiments described in a separate paper.

Sign in / Sign up

Export Citation Format

Share Document