Transformation of the lamellar structure into nanofibrillar structure in the bulk oriented ultra high molecular weight polyethylene: mechanical and tribological properties

2016 ◽  
Vol 26 (4) ◽  
pp. 350-352 ◽  
Author(s):  
Aleksey V. Maksimkin ◽  
Fedor S. Senatov ◽  
Vladimir D. Danilov ◽  
Kseniya S. Mostovaya ◽  
Sergey D. Kaloshkin ◽  
...  
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Tribological Properties ◽  
Lamellar Structure ◽  
Mechanical And Tribological Properties ◽  
Ultra High Molecular Weight

scholarly journals Effect of Adhesion on Mechanical and Tribological Properties of Glass Fiber Composites, Based on Ultra-High Molecular Weight Polyethylene Powders with Various Initial Particle Sizes

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1602 ◽  
Author(s):  
Sergey V. Panin ◽  
Lyudmila A. Kornienko ◽  
Qitao Huang ◽  
Dmitry G. Buslovich ◽  
Svetlana A. Bochkareva ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Glass Fiber ◽  
High Molecular Weight ◽  
Tribological Properties ◽  
Glass Fibers ◽  
Operating Conditions ◽  
Powder Size ◽  
Mechanical And Tribological Properties ◽  
Polymer Powder ◽  
Ultra High Molecular Weight

The aim of this study was to assess the effect of adhesion between the non-polar, ultra-high molecular weight polyethylene (UHMWPE) matrix and the glass fiber fillers of various lengths treated with the commercially available “KH-550” agent, on the mechanical and tribological properties of the UHMWPE-based composites. The motivation was to find the optimal compositions of the polymer composite, for the compression sintering manufacturing of lining plates for the protection of marine venders and construction vehicles, as well as transport equipment. It was shown that the initial powder size at equal molecular weight determined the distribution patterns of the glass fibers in the matrix, and, as a consequence, the mechanical and tribological properties of the composites. Based on the obtained experimental data and the results of the calculation by a developed computer algorithm, control parameters were determined to give practical recommendations (polymer powder size and glass fiber length), for the production of the UHMWPE-composites having specified mechanical and tribological characteristics. The “GUR4022 + 10% LGF” composite, loaded with the chopped 3 mm glass fibers treated with the “KH-550”, was recommended for severe operating conditions (high loads, including impact and abrasive wear). For mild operating conditions (including cases when the silane coupling agent could not be used), the “GUR2122 + 10% MGF” and “GUR2122 + 10% LGF” composites, based on the fine UHMWPE powder, were recommended. However, the cost and technological efficiency of the filler (flowability, dispersibility) and polymer powder processing should be taken into account, in addition to the specified mechanical and tribological properties.

scholarly journals The Influence of Irradiation and Accelerated Aging on the Mechanical and Tribological Properties of the Graphene Oxide/Ultra-High-Molecular-Weight Polyethylene Nanocomposites

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Guodong Huang ◽  
Zifeng Ni ◽  
Guomei Chen ◽  
Yongwu Zhao
Keyword(s):  
Molecular Weight ◽  
Graphene Oxide ◽  
High Molecular Weight ◽  
Tribological Properties ◽  
Gamma Ray ◽  
Accelerated Aging ◽  
Artificial Joint ◽  
Promising Candidate ◽  
Mechanical And Tribological Properties ◽  
Ultra High Molecular Weight

Graphene oxide/ultra-high-molecular-weight polyethylene (GO/UHMWPE) nanocomposite is a potential and promising candidate for artificial joint applications. However, after irradiation and accelerated aging, the mechanical and tribological behaviors of the nanocomposites are still unclear and require further investigation. GO/UHMWPE nanocomposites were successfully fabricated using ultrasonication dispersion, ball-milling, and hot-pressing process. Then, the nanocomposites were irradiated by gamma ray at doses of 100 kGy. Finally, GO/UHMWPE nanocomposites underwent accelerated aging at 80°C for 21 days in air. The mechanical and tribological properties of GO/UHMWPE nanocomposites have been evaluated after irradiation and accelerated aging. The results indicated that the incorporation of GO could enhance the mechanical, wear, and antiscratch properties of UHMWPE. After irradiation, these properties could be further enhanced, compared to unirradiated ones. After accelerated aging, however, these properties have been significantly reduced when compared to unirradiated ones. Moreover, GO and irradiation can synergistically enhance these properties.

scholarly journals Fabrication and Evaluation of Mechanical and Tribological Properties of ultra-high-molecular-weight polyethylene-based Nanocomposites Reinforced with Hydroxyapatite, Zirconia and Multi-walled Carbon Nanotubes

2021 ◽  
Author(s):  
Alireza Nikbakht ◽  
Jafar Javadpour ◽  
Mohammd Reza Naimi-Jamal ◽  
Hamidreza Rezaie
Keyword(s):  
Carbon Nanotubes ◽  
Molecular Weight ◽  
High Molecular Weight ◽  
Tribological Properties ◽  
Cell Attachment ◽  
Mechanical And Tribological Properties ◽  
Optimum Proportion ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Ultra High Molecular Weight

The unique properties of ultra-high-molecular-weight polyethylene (UHMWPE) have made composites based on this polymer the gold standard choice for articulating surfaces used in arthroplasty. However, wear debris released by prosthesis is still a major concern of the implants. In this study, we address the urgent need to revisit the current methodologies used in designing these biomaterials by fabricating UHMWPE-based nanocomposite with Hydroxyapatite (HA), Multi-walled Carbon Nanotubes (MWCNTs), and Zirconia as additives. We investigated how different combinations of these additives impact the nanocomposites' hardness, plasticity index (PI), and friction coefficient. Our results show a constant increase in hardness by increasing Zirconia. The MTT assay test and Scanning Electron Microscopy (SEM) demonstrated an increase in cell attachment and cell viability. Examining various additives' amounts, we can further explore the possibility of reaching an optimum proportion of the ingredients. Compared with other UHMWPE-based nanocomposites (UHMWPE-HA-MWCNT's), the fabricated nanocomposite shows an improvement in tribological properties.

Sign in / Sign up

Export Citation Format

Share Document