Study of microstructure and mechanical properties of aluminium alloy (AA-6351-T6) using friction stir welding

2020 ◽  
Vol 27 ◽  
pp. 1733-1737
Author(s):  
Pramod Kumar ◽  
Rajesh Kumar ◽  
Bidesh Kumar Hembram ◽  
M. Murugan ◽  
Abdul Arif ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties

Microstructure and Mechanical Properties of the Aluminium Alloy 6056 Welded by Friction Stir Welding Techniques

2006 ◽  
Vol 50 (11-12) ◽  
pp. 98-106 ◽  
Author(s):  
A. L. Lafly ◽  
D. Alléhaux ◽  
F. Marie ◽  
C. Dalle Donne ◽  
G. Biallas
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties

Effects of friction stir welding on microstructure and mechanical properties of 6063 aluminium alloy

2018 ◽  
Vol 5 (2) ◽  
pp. 8348-8353 ◽  
Author(s):  
J. Sai Sashank ◽  
P. Sampath ◽  
P. Sai Krishna ◽  
R. Sagar ◽  
S. Venukumar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties

scholarly journals Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1938
Author(s):  
Haifeng Yang ◽  
Hongyun Zhao ◽  
Xinxin Xu ◽  
Li Zhou ◽  
Huihui Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Weld Nugget ◽  
Al Alloy ◽  
Nugget Zone ◽  
T Joints ◽  
Friction Stir ◽  
Stationary Shoulder ◽  
Microstructure And Mechanical Properties

In this study, 2A14-T4 Al-alloy T-joints were prepared via stationary shoulder friction stir welding (SSFSW) technology where the stirring pin’s rotation speed was set as different values. In combination with the numerical simulation results, the macro-forming, microstructure, and mechanical properties of the joints under different welding conditions were analyzed. The results show that the thermal cycle curves in the SSFSW process are featured by a steep climb and slow decreasing variation trends. As the stirring pin’s rotation speed increased, the grooves on the weld surface became more obvious. The base and rib plates exhibit W- or N-shaped hardness distribution patterns. The hardness of the weld nugget zone (WNZ) was high but was lower than that of the base material. The second weld’s annealing effect contributed to the precipitation and coarsening of the precipitated phase in the first weld nugget zone (WNZ1). The hardness of the heat affect zone (HAZ) in the vicinity of the thermo-mechanically affected zone (TMAZ) dropped to the minimum. As the stirring pin's rotation speed increased, the tensile strengths of the base and rib plates first increased and then dropped. The base and rib plates exhibited ductile and brittle/ductile fracture patterns, respectively.

Sign in / Sign up

Export Citation Format

Share Document