Experimental investigation on AW 106 Epoxy/E-Glass fiber/nano clay composite for wind turbine blade

2020 ◽  
Vol 21 ◽  
pp. 202-205 ◽  
Author(s):  
K. Ansal Muhammed ◽  
C. Ramesh Kannan ◽  
B. Stalin ◽  
M. Ravichandran
Keyword(s):  
Experimental Investigation ◽  
Wind Turbine ◽  
Glass Fiber ◽  
Turbine Blade ◽  
Wind Turbine Blade ◽  
Nano Clay

Experimental investigation of the effect of active flow control on the wake of a wind turbine blade

2021 ◽  
pp. 095440622110089
Author(s):  
GholamHossein Maleki ◽  
Ali Reza Davari ◽  
Mohammad Reza Soltani
Keyword(s):  
Experimental Investigation ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Active Flow Control ◽  
Leading Edge ◽  
Wind Turbine Blade ◽  
Plasma Actuators ◽  
Plasma Actuation ◽  
Surface Pressure Distribution ◽  
Stall Angle

An extensive experimental investigation was conducted to study the effects of Dielectric Barrier Discharge (DBD), on the flow field of an airfoil at low Reynolds number. The DBD was mounted near the leading edge of a section of a wind turbine blade. It is believed that DBD can postpone the separation point on the airfoil by injecting momentum to the flow. The effects of steady actuations on the velocity profiles in the wake region have been investigated. The tests were performed at α = 4 to 36 degrees i.e. from low to deep stall angles of attack regions. Both surface pressure distribution and wake profile show remarkable improvement at high angles of attack, beyond the static stall angle of the airfoil when the plasma actuation was implemented. The drag calculated from the wake momentum deficit has further shown the favorable role of the plasma actuators to control the flow over the airfoil at incidences beyond the static stall angle of attack of this airfoil. The results demonstrated that DBD has been able to postpone the stall onset significantly. It has been observed that the best performance for the plasma actuation for this airfoil is in the deep stall angles of attack range. However, below and near the static stall angles of attack, plasma augmentation was pointed out to have a negligible improvement in the aerodynamic behavior.

Flow Behavior in the Resin Infusion of Glass Fiber Reinforced Polymer Wind Turbine Blade

2013 ◽  
Vol 686 ◽  
pp. 118-124 ◽  
Author(s):  
Mohd Azuan Mohd Azlan ◽  
Muhamad Ridzuan Abdul Latif ◽  
Mohamad Zaki Abdullah ◽  
Kamal Arif Zainal Abidin ◽  
Azmi Abdul Wahab
Keyword(s):  
Wind Turbine ◽  
Glass Fiber ◽  
Turbine Blade ◽  
Wind Turbine Blade ◽  
Fiber Reinforced Polymer ◽  
Glass Fiber Reinforced Polymer ◽  
Resin Infusion ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Over Time

This paper presents the monitoring of resin flow during resin infusion process in the fabrication of glass fiber reinforced polymer GRP wind turbine blade (WTB). Epoxy type of resin was used as the matrix and its viscosity and gel time were determined in-house. Next, resin infusions were done to obtain the permeability of the glass fiber in different directions (longitudinal and transverse), given the specific number of layers. The fabrication of composite WTB by resin infusion was conducted with the introduction of 'moldless' setup, where both upper and lower skins are covered by flexible mould/vacuum bag without any rigid female mould. However, a wooden core is used and acts as an “inner” mould to obtain the wind turbine shape. The whole infusion process was video recorded and the flow front pattern was traced at certain time intervals to investigate the infused percentage area over time. Afterward, guided by the traces of flow patterns on grid and video observation, 3D models of resin infused at interval times are generated in a CAD software. From the models, the area infused was determined. Percentage of area infused over time was compared with the analytical plot based on Darcy's law. A good agreement was found between the experimental observation and the theoretical plot.

Layup Analyzing of a Carbon/Glass Hybrid Composite Wind Turbine Blade Using Finite Element Analysis

2011 ◽  
Vol 87 ◽  
pp. 49-54 ◽  
Author(s):  
Hai Chen Lin
Keyword(s):  
Finite Element ◽  
Carbon Fiber ◽  
Wind Turbine ◽  
Glass Fiber ◽  
Turbine Blade ◽  
Carbon Fibers ◽  
Fiber Composite ◽  
Wind Turbine Blade ◽  
Fiber Reinforced ◽  
Carbon Fiber Composite

This thesis use AOC15/50 blade as baseline model which is a composite wind turbine blade made of glass/epoxy for a horizontal axis wind turbine. A finite element modeling of composite wind turbine blade was created using the SHELL element of ANSYS. Then we study how to use the carbon fiber material replaces the glass fiber to make the hybrid blade, and find a suitable layup to improve the performance of the blade. The hybrid blade was made through introducing carbon fibers. Different models, with introducing different number of carbon fibers, 75% carbon fibers replace unidirectional glass fibers in spar cap of blade model which can achieve best structure performance. The wind turbine blades are often fabricated by hand using multiple of glass fiber-reinforced polyester resin or glass fiber-reinforced epoxy resin. As commercial machines get bigger, this could not to meet the demands. The advantages of carbon fiber composite materials are used by blade producer. Studies show that carbon fiber has high strength-to-weight ratio and resistance fatigue properties. Carbon fiber is mixed with epoxy resin to make into carbon fiber-reinforced polymer. Carbon fiber-reinforced polymer is the one of best blade materials for resistance bad weather. The stiffness of carbon fiber composite is 2 or 3 times higher than glass fiber composite [1], but the cost of carbon fiber composite is 10 times higher than glass fiber composite. If all of wind turbine blades are made of carbon fiber composite, it will be very expensive. Therefore carbon/glass fiber hybrid composite blade has become a research emphasis in the field of blade materials. This paper gives an example of finite element modeling composite wind turbine blade in ANSYS by means of the medium-length blade of AOC 15/50 horizontal axis wind turbine. This model can be directly used in dynamics analysis and does not need to be imported from the CAD software into finite element program. This finite element modeling of composite wind turbine blade was created using the SHELL element of ANSYS. Then we study how to use the carbon fiber material replaces the glass fiber to make the hybrid blade, and find a suitable lay-up to improve the performance of the blade.

Sign in / Sign up

Export Citation Format

Share Document