Experimental Investigations On Friction Stir Spot Welding Process Of Dissimilar Metals

2018 ◽  
Vol 5 (5) ◽  
pp. 12056-12061
Author(s):  
S. Indumathi ◽  
G. Rajyalakshmi ◽  
K. Rajasekhar
Keyword(s):  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Experimental Investigations ◽  
Dissimilar Metals ◽  
Friction Stir

Friction Stir Spot Welding-Process and Weld Properties: A Review

2021 ◽  
Author(s):  
Chaitanya Sharma ◽  
Ajay Tripathi ◽  
Vikas Upadhyay ◽  
Vijay Verma ◽  
Sumit K. Sharma
Keyword(s):  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Friction Stir ◽  
Weld Properties

Thermo-mechanical modelling of the Friction Stir Spot Welding process: Effect of the friction models on the heat generation mechanisms

2022 ◽  
pp. 146442072110709
Author(s):  
Nasra Hannachi ◽  
Ali Khalfallah ◽  
Carlos Leitão ◽  
Dulce Rodrigues
Keyword(s):  
Numerical Simulation ◽  
Heat Generation ◽  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Frictional Heat ◽  
Contact Conditions ◽  
Friction Stir ◽  
Friction Models ◽  
Generation Mechanisms

Friction Stir Spot Welding involves complex physical phenomena, which are very difficult to probe experimentally. In this regard, the numerical simulation may play a key role to gain insight into this complex thermo-mechanical process. It is often used to mimic specific experimental conditions to forecast outputs that may be substantial to analyse and elucidate the mechanisms behind the Friction Stir Spot Welding process. This welding technique uses frictional heat generated by a rotating tool to join materials. The heat generation mechanisms are governed by a combination of sliding and sticking contact conditions. In the numerical simulation, these contact conditions are thoroughly dependent on the used friction model. Hence, a successful prediction of the process relies on the appropriate selection of the contact model and parameters. This work aims to identify the pros and cons of different friction models in modelling combined sliding-sticking conditions. A three-dimensional coupled thermo-mechanical FE model, based on a Coupled Eulerian-Lagrangian formulation, was developed. Different friction models are adopted to simulate the Friction Stir Spot Welding of the AA6082-T6 aluminium alloy. For these friction models, the temperature evolution, the heat generation, and the plastic deformation were analysed and compared with experimental results. It was realized that numerical analysis of Friction Stir Spot Welding can be effective and reliable as long as the interfacial friction characteristics are properly modelled. This approach may be used to guide the contact modelling strategy for the simulation of the Friction Stir Spot Welding process and its derivatives.

Advanced Approach to Modify Friction Stir Spot Welding Process

2019 ◽  
Vol 26 (10) ◽  
pp. 1562-1573 ◽  
Author(s):  
Behrouz Bagheri ◽  
Mahmoud Abbasi ◽  
Amin Abdollahzadeh ◽  
Hamid Omidvar
Keyword(s):  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Friction Stir

Effect of Tool Shape on Temperature Field in Friction Stir Spot Welding

2013 ◽  
Vol 58 (2) ◽  
pp. 595-599 ◽  
Author(s):  
P. Lacki ◽  
Z. Kucharczyk ◽  
R.E. Śliwa ◽  
T. Gałaczyński
Keyword(s):  
Temperature Field ◽  
Solid State ◽  
Spot Welding ◽  
Plastic Material ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Frictional Heat ◽  
Maximum Temperature ◽  
Tool Geometry ◽  
Friction Stir

Friction stir welding (FSW) is one of the youngest methods of metal welding. Metals and its alloys are joined in a solid state at temperature lower than melting points of the joined materials. The method is constantly developed and friction stir spot welding (FSSW) is one of its varieties. In the friction stir spot welding process a specially designed tool is brought into rotation and plunged, straight down, in the joined materials. Heat is generated as a result of friction between the tool and materials, and plastic deformation of the joined materials. Softening (plastic zone) of the joined materials occurs. Simultaneously the materials are stirred. After removal of the tool, cooling down the stirred materials create a solid state joint. Numerical simulation of the process was carried out with the ADINA System based on the finite element method (FEM). The problem was considered as an axisymmetric one. A thermal and plastic material model was assumed for Al 6061-T6. Frictional heat was generated on the contact surfaces between the tool and the joined elements. The model of Coulomb friction, in which the friction coefficient depends on the temperature, was used. An influence of the tool geometry on heat generation in the welded materials was analysed. The calculations were carried out for different radiuses of the tool stem and for different angles of the abutment. Temperature distributions in the welded materials as a function of the process duration assuming a constant value of rotational tool speed and the speed of tool plunge were determined. Additionally, the effect of the stem radius and its height on the maximum temperature was analysed. The influence of tool geometry parameters on the temperature field and the temperature gradient in the welded materials was shown. It is important regarding the final result of FSSW.

Influence of Heating Friction Stir Spot Welding Process Parameters on Steel Aluminum Forming Quality

2018 ◽  
Vol 917 ◽  
pp. 246-251
Author(s):  
Kai Xu ◽  
Shu Quan Zhang
Keyword(s):  
Spot Welding ◽  
Welding Process ◽  
Friction Stir Spot Welding ◽  
Joint Line ◽  
Welding Parameters ◽  
Forming Quality ◽  
Rotating Speed ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Welding Pressure

A lap welding experiment of DP590 steel and 6061 aluminum plate is carried out by using Heating Friction Stir Spot Welding (HFSSW) to study the influence of welding parameters on the forming quality. The results show that a lap joint with better forming can be obtained for the dissimilar metal of steel and aluminum. Under the condition that the rotating speed of the stirring tool is 1000r/min, the penetration depth, 0.2mm, the dwell time, 90s, the welding pressure, 0.2Mp, and the flow rate of cooling air, 20L/min, the forming quality of the surface of the joint line is good & bright, and the exit hole is also smaller. The mechanism of heat production is revealed in the following: the main heat is produced by the friction between the stirring tool shoulder and the welded part & between the probe and the welded part as well as by the latent heat resulted from the plastic deformation of the material in joint line during welding.

Sign in / Sign up

Export Citation Format

Share Document