The Effects of Ageing Temperature and Time on Mechanical Properties of A356 Aluminium cast Alloy with Red Mud Addition and Treated By T6 Heat Treatment

2015 ◽  
Vol 2 (4-5) ◽  
pp. 1200-1209 ◽  
Author(s):  
B. Geetha ◽  
K. Ganesan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Red Mud ◽  
Cast Alloy ◽  
Ageing Temperature ◽  
T6 Heat Treatment

scholarly journals The Effect of Ageing Temperature in T6 Heat Treatment on Mechanical Properties of AA7075

2019 ◽  
Vol 135 (4) ◽  
pp. 732-734
Author(s):  
I. Simsek ◽  
D. Simsek ◽  
T. Tuncay ◽  
D. Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Ageing Temperature ◽  
T6 Heat Treatment

Effect of Alloying Elements on Mechanical Properties of Al-Si-Cu-Mg Cast Alloys

2015 ◽  
Vol 817 ◽  
pp. 127-131
Author(s):  
Yan Peng Pan ◽  
Zhi Feng Zhang ◽  
Bao Li ◽  
Bi Cheng Yang ◽  
Jun Xu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Performance ◽  
Cast Alloy ◽  
Experimental Results ◽  
Alloying Elements ◽  
Mg Alloy ◽  
T6 Heat Treatment ◽  
Specific Composition ◽  
Cast Alloys

To develop Al-Si cast alloys with high performance is important for lightweighting vehicles. In this study, the effects of the alloying elements such as Si, Cu, Mg contents (5%-7% Si, 1%-3%Cu, 0.3%-0.9%Mg) on mechanical properties of a test Al-Si-Cu-Mg cast alloy was studied to achieve a specific composition. The experimental results show that the Al-6%Si-3%Cu-0.3%Mg alloy has better comprehensive mechanical properties after T6 heat treatment, which indicates a remarkable interaction of the alloying elements for improving performance.

scholarly journals Effect of Ce Addition and Heat Treatment on Microstructure Evolution and Tensile Properties of Industrial A357 Cast Alloy

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1100
Author(s):  
Yanfeng Wang ◽  
Qian Liu ◽  
Zheng Yang ◽  
Changming Qiu ◽  
Kuan Tan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Rare Earth ◽  
Tensile Properties ◽  
Cast Alloy ◽  
Fracture Pattern ◽  
Unmodified Alloy ◽  
Constitutional Undercooling ◽  
T6 Heat Treatment ◽  
Eutectic Si

The effects of adding different Ce contents (0–0.32 wt.%) on the microstructure, mechanical properties, and fracture morphology of industrial A357 cast alloy in as-cast and T6 heat treatment were studied. The main purpose of this study is to improve the microstructure stability and tensile properties of industrial A357 cast alloy. The microstructural analyses indicate that the addition of Ce causes refinement of the α-Al primary phase for the reason that the formation of intermetallic compounds containing (AlSiCeMg) elements enriches the front of the solid–liquid interface, which causes an increase in constitutional undercooling. Simultaneously, the addition of Ce also affected the characteristics of eutectic Si particles, which make its morphology change from acicular structures into fragmented and spheroidized. This is mainly due to the formation of Ce-rich precipitates during solidification, which increase the constitutional undercooling and suppress the nucleation of the eutectic Si particles, resulting in the change of eutectic Si characteristics. Moreover, the needle-like morphology of a Fe-containing intermetallic is transformed into α(AlSiFeCe) phase containing rare earth Ce when part of the Ce atoms entered β(Al5FeSi) phase compounds. The tensile properties of the modified alloys were improved in the as-cast and T6 heat treatment as a consequence of simultaneous refinement of both secondary dendrite arm spacing and grains and the improvement of eutectic Si particles and Fe-containing intermetallic morphology. The fracture surface of the modified alloy has more dimples than the unmodified alloy, which indicates that the main fracture pattern of the modified alloy is dimple fracture caused by the crack of eutectic Si particles. The optimal percentage of Ce in industrial A357 cast alloy was determined to be 0.16 wt.% according to the change of microstructures structure and mechanical properties. These experimental results provide a new basis for adding rare earth Ce to improve the performance of parts in the actual production of industrial A357 cast alloy.

Solidification Behavior and Mechanical Properties of Al-Si-Mg Alloy with Ti Addition

2016 ◽  
Vol 850 ◽  
pp. 594-602 ◽  
Author(s):  
Cong Xu ◽  
Cheng Yuan Wang ◽  
Hai Jun Yang ◽  
Zhi Guo Liu ◽  
Hiroshi Yamagata ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cast Alloy ◽  
Solidification Behavior ◽  
A357 Alloy ◽  
T6 Heat Treatment ◽  
Interdendritic Space ◽  
Cast Alloys ◽  
Ti Addition ◽  
Strength And Ductility

The solidification behavior, microstructural evolution and mechanical properties of Al-Si-Mg foundry alloy with different Ti additions were investigated in the present study. The solidification behavior of those A357 alloys was analyzed through thermal analysis. The microstructures were examined by optical microscopy (OM), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The results showed that the addition of Ti could refine grains of A357 as-cast alloy due to a good restriction on the grain growth, but Ti could not refine secondary dendrite arm spacing (SDAS), thus mechanical properties of the A357 as-cast alloy did not improved significantly. After T6 heat treatment, the microstructure with α-Al dendrites with the Al-Si eutectics at interdendritic space was replaced by a homogeneous α-Al matrix with a nonuniform dispersion of discrete, spheroidizing and coarse silicon particles. Hence, compared with the as-cast alloys, both of the strength and ductility of the T6 treated alloys are significantly improved, and an optimal combination of strength and elongation of the A357 alloy can be achieved by the 0.8 wt.% Ti addition after T6 heat treatment.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

scholarly journals The Phase Composition and Mechanical Properties of the Novel Precipitation-Strengthening Al-Cu-Er-Mn-Zr Alloy

2020 ◽  
Vol 10 (15) ◽  
pp. 5345
Author(s):  
Sayed Amer ◽  
Olga Yakovtseva ◽  
Irina Loginova ◽  
Svetlana Medvedeva ◽  
Alexey Prosviryakov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Phase Composition ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Precipitation Strengthening ◽  
The Novel ◽  
Annealed Alloy ◽  
Zr Alloy

The microstructure, phase composition, and mechanical properties during heat treatment and rolling of the novel Al-5.0Cu-3.2Er-0.9Mn-0.3Zr alloy were evaluated. A new quaternary (Al,Cu,Mn,Er) phase with possible composition Al25Cu4Mn2Er was found in the as-cast alloy. Al20Cu2Mn3 and Al3(Zr,Er) phases were nucleated during homogenization, and θ″(Al2Cu) precipitates were nucleated during aging. The metastable disc shaped θ″(Al2Cu) precipitates with a thickness of 5 nm and diameter of 100–200 nm were nucleated mostly on the Al3(Zr,Er) phase precipitates with a diameter of 35 nm. The hardness Vickers (HV) peak was found after the annealing of a rolled alloy at 150 °C due to strengthening by θ″(A2Cu) precipitates, which have a larger effect in materials hardness than do the softening processes. The novel Al-Cu-Er-Mn-Zr alloy has a yield strength (YS) of 320–332 MPa, an ultimate tensile strength (UTS) of 360–370 MPa, and an El. of 3.2–4.0% in the annealed alloy after rolling condition.

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

2019 ◽  
Vol 944 ◽  
pp. 64-72
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Ya Qi Deng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
Filler Wire ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Before And After

Bulky sample was made by using TIG wire and arc additive manufacturing (WAAM) technology, in which Ф1.6 mm filler wire of in-situ TiB2/Al-Si composites was selected as deposition metal, following by T6 heat treatment. The microstructure and mechanical properties of the bulky sample before and after heat treatment were analyzed. Experimental results showed that the texture of the original samples parallel to the weld direction and perpendicular to the weld direction was similar consisting of columnar dendrites and equiaxed crystals. After T6 heat treatment, the hardness of the sample was increased to 115.85 HV from 62.83 HV, the yield strength of the sample was 273.33 MPa, the average tensile strength was 347.33 MPa, and the average elongation after fracture was 7.96%. Although pore defects existed in the fracture, yet the fracture of the sample was ductile fracture.

Sign in / Sign up

Export Citation Format

Share Document