High temperature deformation behavior and constitutive modeling for 20CrMnTiH steel

2014 ◽  
Vol 57 ◽  
pp. 465-471 ◽  
Author(s):  
Wei Feng ◽  
Youheng Fu
Keyword(s):  
High Temperature ◽  
Constitutive Modeling ◽  
Deformation Behavior ◽  
High Temperature Deformation ◽  
Temperature Deformation

High Temperature Deformation Mechanism Maps of NiAl

2004 ◽  
Vol 449-452 ◽  
pp. 57-60
Author(s):  
I.G. Lee ◽  
A.K. Ghosh
Keyword(s):  
High Temperature ◽  
Strain Rate ◽  
Deformation Mechanism ◽  
Calculation Method ◽  
Deformation Behavior ◽  
Tensile Tests ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Grain Sizes ◽  
Temperature Strain

In order to analyze high temperature deformation behavior of NiAl alloys, deformation maps were constructed for stoichiometric NiAl materials with grain sizes of 4 and 200 µm. Relevant constitute equations and calculation method will be described in this paper. These maps are particularly useful in identifying the location of testing domains, such as creep and tensile tests, in relation to the stress-temperature-strain rate domains experienced by NiAl.

Characterization of High Temperature Deformation Behavior of BFe10-1-2 Cupronickel Alloy Using Orthogonal Analysis

2017 ◽  
Vol 36 (7) ◽  
pp. 701-710
Author(s):  
Jun Cai ◽  
Kuaishe Wang ◽  
Xiaolu Zhang ◽  
Wen Wang
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Constitutive Equation ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Compression Tests ◽  
Statistical Parameters ◽  
Orthogonal Analysis

AbstractHigh temperature deformation behavior of BFe10-1-2 cupronickel alloy was investigated by means of isothermal compression tests in the temperature range of 1,023~1,273 K and strain rate range of 0.001~10 s–1. Based on orthogonal experiment and variance analysis, the significance of the effects of strain, strain rate and deformation temperature on the flow stress was evaluated. Thereafter, a constitutive equation was developed on the basis of the orthogonal analysis conclusions. Subsequently, standard statistical parameters were introduced to verify the validity of developed constitutive equation. The results indicated that the predicted flow stress values from the constitutive equation could track the experimental data of BFe10-1-2 cupronickel alloy under most deformation conditions.

Constitutive Analysis of the High-Temperature Deformation Behavior of Single Phase α-Ti and α+β Ti-6Al-4V Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 3607-3612 ◽  
Author(s):  
Jeoung Han Kim ◽  
Jong Taek Yeom ◽  
Nho Kwang Park ◽  
Chong Soo Lee
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Deformation Behavior ◽  
Single Phase ◽  
Volume Fraction ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Β Phase ◽  
Α Phase ◽  
Self Consistent

The high-temperature deformation behavior of the single-phase α (Ti-7.0Al-1.5V) and α + β (Ti-6Al-4V) alloy were determined and compared within the framework of self-consistent scheme at various temperature ranges. For this purpose, isothermal hot compression tests were conducted at temperatures between 650°C ~ 950°C to determine the effect of α/β phase volume fraction on average flow stress under hot-working condition. The flow behavior of α phase was estimated from the compression test results of single-phase α alloy whose chemical composition is close to that of α phase of Ti-6Al-4V alloy. On the other hand, the flow stress of β phase in Ti-6Al-4V was predicted by using self-consistent method. The flow stress of α phase was higher than that of β phase above 750°C, while the β phase revealed higher flow stress than α phase at 650°C. Also, at temperature above 750°C, the predicted strain rate of β phase was higher than that of α phase. It was found that the relative strength between α and β phase significantly varied with temperature.

Sign in / Sign up

Export Citation Format

Share Document