Effects of cooling rate and pressure on microstructure and mechanical properties of sub-rapidly solidified Mg–Zn–Sn–Al–Ca alloy

2013 ◽  
Vol 45 ◽  
pp. 300-307 ◽  
Author(s):  
Jihua Chen ◽  
Juying Wei ◽  
Hongge Yan ◽  
Bin Su ◽  
Xueqiang Pan
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Microstructure And Mechanical Properties ◽  
Rapidly Solidified

scholarly journals Effect of Cooling Rate and Ti Addition on the Microstructure and Mechanical Properties in As-cast Condition of Hypereutectic High Chromium Cast Irons

2012 ◽  
Vol 52 (12) ◽  
pp. 2210-2219 ◽  
Author(s):  
Qiang Liu ◽  
Hongwei Zhang ◽  
Qiang Wang ◽  
Xiangkui Zhou ◽  
P^|^auml;r G. J^|^ouml;nsson ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Cast Irons ◽  
High Chromium ◽  
Microstructure And Mechanical Properties ◽  
Cast Condition ◽  
Ti Addition

Microstructure and Mechanical Properties of Al-12.6%Si Composite Reinforced by Al63Cu25Fe12Quasicrystal

2012 ◽  
Vol 182-183 ◽  
pp. 162-166
Author(s):  
Can Can Li ◽  
Hao Ran Geng ◽  
Zhen Yuan Li ◽  
Hai Ou Qin
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Cooling Rate ◽  
Quasicrystalline Phase ◽  
Melt Temperature ◽  
Microstructure And Mechanical Properties

In this paper, Al-12.6%Si/Al63Cu25Fe12 composites were fabricated by method of casting. The microstructure and chemical composition of Al63Cu25Fe12 quasicrystal alloy and Al-12.6%Si alloy reinforced by the quasicrystal were studied, and the mechanical properties of Al-12.6%Si composite were also measured. The results show that almost single quasicrystalline phases exist in the samples which are cast with the 1300°C melt. Quickly enough cooling rate and appropriate melt temperature are necessary for the formation of the quasicrystalline phase. In addition, Al-12.6%Si composite has optimal mechanical properties when the amount of Al63Cu25Fe12 quasicrystal is 3 wt%.

scholarly journals Effect of Cooling Rate on Microstructure and Mechanical Properties in the CGHAZ of Electroslag Welded Pearlitic Rail Steel

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 742 ◽  
Author(s):  
Khan ◽  
Yu ◽  
Wang ◽  
Jiang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cooling Rate ◽  
Rail Steel ◽  
Interlamellar Spacing ◽  
Coarse Grained ◽  
Microstructure And Mechanical Properties ◽  
Confocal Scanning Laser ◽  
Start Temperature ◽  
Pearlitic Rail Steel

The effect of cooling rate, ranging from 6 to 1 °C/s, on microstructure and mechanical properties in the coarse-grained heat affected zone (CGHAZ) of electroslag welded pearlitic rail steel has been investigated by using confocal scanning laser microcopy (CSLM) and Gleeble 3500 thermo-mechanical simulator. During heating, the formed austenite was inhomogeneous with fractions of untransformed ferrite, which has influenced the pearlite transformation during cooling by providing additional nucleation sites to pearlite. During cooling, at 6 °C/s, the microstructure was composed of martensite and bainite with little pearlite. From 4 to 1 °C/s, microstructures were completely pearlite. Lowering the cooling rate of the CGHAZ from 4 to 1 °C/s increased the pearlite start temperature and reduced the pearlite growth rate. Meanwhile, this increase in pearlite start temperature enlarged the pearlite interlamellar spacing. Alternatively, increasing pearlite interlamellar spacing in the CGHAZ by lowering the cooling rate from 6 to 1 °C/s reduced the hardness and tensile strength, whereas toughness was found unaffected by the pearlite interlamellar spacing. It has been found that a cooling rate of 4 °C/s leads to the formation of pearlite with fine interlamellar spacing of 117 nm in the CGHAZ of electroslag welded pearlitic rail steel where hardness is 425 HV, tensile strength is 1077 MPa, and toughness is 9.1 J.

Sign in / Sign up

Export Citation Format

Share Document