Experimental and numerical investigations about the combined effect of interference fit and bolt clamping on the fatigue behavior of Al 2024-T3 double shear lap joints

2012 ◽  
Vol 33 ◽  
pp. 425-435 ◽  
Author(s):  
T.N. Chakherlou ◽  
B. Abazadeh
Keyword(s):  
Fatigue Behavior ◽  
Lap Joints ◽  
Combined Effect ◽  
Interference Fit ◽  
Numerical Investigations ◽  
Double Shear ◽  
Al 2024

Effect of Interference-Fit on Fatigue Life for Composite Lap Joints

2014 ◽  
Vol 939 ◽  
pp. 39-46 ◽  
Author(s):  
Hong Qian Xue ◽  
Qian Tao ◽  
Emin Bayraktar
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Fatigue Tests ◽  
Lap Joints ◽  
Finite Element Simulations ◽  
Cyclic Loads ◽  
Lap Joint ◽  
Interference Fit ◽  
3D Finite Element ◽  
Double Shear

The aim of this study is to examine the effect of the clearance and interference-fit on the fatigue life of composite lap joints in double shear, 3D finite element simulations have been performed to obtain stress (or strain) distributions around the hole due to interference fit using FEM package, Non-linear contact analyses are performed to examine the effects of the clearance and interference for titanium and composite lap joint. Fatigue tests were conducted for the titanium and composite lap joints with clearance fit and interference fit with 0.5, 1, and 1.5% nominal interference fit levels at different cyclic loads. The results shows that interference fit increases fatigue life compared to clearance fit specimens, the titanium and composite lap joint with 1% interference fit level has the better fatigue life.

Effect of bolt tightening on the fatigue behavior of GLARE double shear lap joints

2021 ◽  
pp. 002199832110033
Author(s):  
B Abazadeh ◽  
HR Maleki
Keyword(s):  
Fatigue Life ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Lap Joints ◽  
Clamping Force ◽  
Test Results ◽  
Load Range ◽  
Double Shear ◽  
Aluminum Sheets ◽  
Aluminum Alloy 2024

In this paper, the effect of bolt torque tightening has been investigated on the fatigue behavior of GLARE in double shear lap configuration. To do so, experimental fatigue tests were conducted using GLARE3-5/4-0.4 specimens with applied torques of 0 (finger tightened), 2 and 4 Nm at different cyclic longitudinal load ranges to achieve the stress-life (S-N) curves. The results revealed that applying and increasing the clamping force enhances the fatigue life of the GLARE specimens. Furthermore, comparison of fatigue test results of GLARE and available monolithic aluminum alloy 2024-T3 plates indicated when the applied load range is low, the effect of clamping force is more noticeable in GLARE specimens due to longer fatigue crack growth life of GLARE. Also, the occurrence of fretting fatigue didn’t reduce the fatigue life of GLARE specimens considerably in contrary to aluminum sheets because of the laminated structure of GLARE. The obtained results can provide insights in designing bolted GLARE joints with superior fatigue in-service performance.

scholarly journals Experimental Study of the Influence of the Surface Preparation on the Fatigue Behavior of Polyamide Single Lap Joints

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1008
Author(s):  
Francesco Musiari ◽  
Fabrizio Moroni
Keyword(s):  
Experimental Study ◽  
Fatigue Behavior ◽  
Atmospheric Pressure Plasma ◽  
Surface Preparation ◽  
Lap Joints ◽  
Polymeric Surfaces ◽  
Adhesively Bonded Joints ◽  
Single Lap Joints ◽  
Number Of Cycles ◽  
Structural Adhesive

The low quality of adhesion performance on polymeric surfaces has forced the development of specific pretreatments able to toughen the interface between substrate and adhesive. Among these methods, atmospheric pressure plasma treatment (APPT) appears particularly suitable for its environmental compatibility and its effectiveness in altering the chemical state of the surface. In this work, an experimental study on adhesively bonded joints realized using polyamide as substrates and polyurethane as the structural adhesive was carried out with the intent to characterize their fatigue behavior, which represents a key issue of such joints during their working life. The single lap joint (SLJ) geometry was chosen and several surface pretreatments were compared with each other: degreasing, abrasion (alone and followed by APPT) and finally APPT. The results show that the abrasion combined with APPT presents the most promising behavior, which appears consistent with the higher percentage of life spent for crack propagation found by means of DIC on this class of joints with respect to the others. APPT alone confers a good fatigue resistance with respect to the simple abrasion, especially at a low number of cycles to failure.

Fatigue behavior of adhesively bonded glass fiber reinforced plastic composites with different overlap lengths

2015 ◽  
Vol 229 (7) ◽  
pp. 1292-1299
Author(s):  
E Kara ◽  
A Kurşun ◽  
MR Haboğlu ◽  
HM Enginsoy ◽  
H Aykul
Keyword(s):  
Glass Fiber ◽  
Fatigue Behavior ◽  
Laminated Composite ◽  
Element Model ◽  
Treatment Method ◽  
Epoxy Adhesive ◽  
Lap Joints ◽  
Adhesively Bonded ◽  
Glass Fiber Reinforced Plastic ◽  
Glass Fiber Reinforced

The joining techniques of lightweight and strong materials in the transport industry (e.g. automotive, aerospace, shipbuilding industries) are very important for the safety of the entire structure. In these industries, when compared with other joining methods, the use of adhesively bonded joints presents unique properties such as greater strength, design flexibility, and reduction in fuel consumption, all thanks to low weight. The aim of this study was the analysis of the tensile fatigue behavior of adhesively bonded glass fiber/epoxy laminated composite single-lap joints with three different specimen types including 30, 40 and 50 mm overlap lengths. In this study, composite adherents were manufactured via vacuum-assisted resin transfer molding and were bonded using Loctite 9461 A&B toughened epoxy adhesive. The effect of a surface treatment method on the bonding strength was considered and it led to an increment of about 40%. A numerical analysis based on a finite element model was performed to predict fatigue life curve, and the predicted results showed good agreement with the experimental investigation.

Sign in / Sign up

Export Citation Format

Share Document