scholarly journals Semi-active control of magnetorheological elastomer base isolation system utilising learning-based inverse model

2017 ◽  
Vol 406 ◽  
pp. 346-362 ◽  
Author(s):  
Xiaoyu Gu ◽  
Yang Yu ◽  
Jianchun Li ◽  
Yancheng Li
Keyword(s):  
Active Control ◽  
Base Isolation ◽  
Inverse Model ◽  
Magnetorheological Elastomer ◽  
Isolation System ◽  
Base Isolation System

Analysis of Vibration Control due to Strong Earthquakes

2010 ◽  
Vol 163-167 ◽  
pp. 4179-4184 ◽  
Author(s):  
He Len Wu
Keyword(s):  
Control System ◽  
Active Control ◽  
Base Isolation ◽  
Hybrid Control ◽  
Ground Motions ◽  
Isolation System ◽  
System A ◽  
Base Isolation System ◽  
Active Control System ◽  
Hybrid Control System

The paper proposes an aseismic hybrid control system to control the response of structures subjected to large ground motions caused by large magnitude earthquakes. The proposed hybrid control system consists of a base isolation system (laminated rubber bearings) connected to an active control system (a tuned mass damper and an actuator). The base isolation system is used to decouple the horizontal ground motions from the structure, whereas the active control system is used to protect the safety and integrity of the base isolation system. A 5-story benchmark building model is developed to study the effectiveness of the hybrid control system against different ground motions. It was found from the numerical results that rubber bearing system alone shows good performance and resists ground motion due to Hachinohe 1968, Kobe 1995, and Northridge 1994 earthquakes, but is somewhat unable to protect the model against El-Centro 1940 earthquake. After the installation of an active control system onto the rubber-isolated model, further improvements to earthquake resistance against these four earthquakes were observed, especially against the El-Centro earthquake. The merit of the hybrid control system lies in its capability to protect against different ground motions, with varying intensity and frequency content.

scholarly journals Influence of Elastomeric Bearings in Tension on the Seismic Performance of Base-Isolated r.c. Buildings

2020 ◽  
Vol 11 (1) ◽  
pp. 82
Author(s):  
Fabio Mazza ◽  
Mirko Mazza
Keyword(s):  
Base Isolation ◽  
Nonlinear Models ◽  
Vertical Component ◽  
Computer Code ◽  
Nonlinear Phenomena ◽  
Isolation System ◽  
Elastomeric Bearings ◽  
Near Fault ◽  
Base Isolation System ◽  
Near Fault Earthquakes

Elastomeric bearings are commonly used in base-isolation systems to protect the structures from earthquake damages. Their design is usually developed by using nonlinear models where only the effects of shear and compressive loads are considered, but uncertainties still remain about consequences of the tensile loads produced by severe earthquakes like the near-fault ones. The present work aims to highlight the relapses of tension on the response of bearings and superstructure. To this end, three-, seven- and ten-storey r.c. framed buildings are designed in line with the current Italian seismic code, with a base-isolation system constituted of High-Damping-Rubber Bearings (HDRBs) designed for three values of the ratio between the vertical and horizontal stiffnesses. Experimental and analytical results available in literature are used to propose a unified nonlinear model of the HDRBs, including cavitation and post-cavitation of the elastomer. Nonlinear incremental dynamic analyses of the test structures are carried out using a homemade computer code, where other models of HDRBs considering only some nonlinear phenomena are implemented. Near-fault earthquakes with comparable horizontal and vertical components, prevailing horizontal component and prevailing vertical component are considered as seismic input. Numerical results highlight that a precautionary estimation of response parameters of the HDRBs is attained referring to the proposed model, while its effects on the nonlinear response of the superstructure are less conservative.

Sign in / Sign up

Export Citation Format

Share Document