Numerical investigation of formation mechanism of welding residual stress in P92 steel multi-pass joints

2017 ◽  
Vol 244 ◽  
pp. 240-252 ◽  
Author(s):  
Suo Li ◽  
Sendong Ren ◽  
Yanbin Zhang ◽  
Dean Deng ◽  
Hidekazu Murakawa
Keyword(s):  
Residual Stress ◽  
Numerical Investigation ◽  
Formation Mechanism ◽  
Welding Residual Stress ◽  
P92 Steel

Characteristics of Residual Stress in P92 Steel Welds

2007 ◽  
Vol 26-28 ◽  
pp. 1175-1180
Author(s):  
Keun Bong Yoo ◽  
Hyun Sun Choi ◽  
Eui Hyun Kim ◽  
Jae Hoon Kim
Keyword(s):  
Residual Stress ◽  
Compressive Residual Stress ◽  
Diffraction Method ◽  
Welding Residual Stress ◽  
Distribution Characteristics ◽  
X Ray Diffraction ◽  
P92 Steel ◽  
X Ray ◽  
Steel Welds ◽  
Directional Difference

Welding residual stress has important influence on the performance of engineering components. In this paper, the residual stress and FWHM were measured by X-ray diffraction method to investigate characteristics for P92 steel welds. The aim of the study is to estimate the residual stress and FWHM distribution characteristics. A compressive residual stress distributed as a function of depth has a different pattern in welds and base metal. A large tensile residual stress occurs welds and near the HAZ, but approaches gradually zero as away from the welding center. Residual stress and FWHM undergo rapid relaxation after PWHT. Also, FWHM is a scalar quantity without any directional difference and is proportional to hardness on the whole.

Formation Mechanism of Hydrogen-Induced Delayed Cracking in Weld Center of High-Strength Steel

2012 ◽  
Vol 557-559 ◽  
pp. 1304-1307 ◽  
Author(s):  
Jing Qiang Zhang ◽  
Jian Guo Yang ◽  
Jia Jie Wang ◽  
Xue Song Liu ◽  
Zhi Bo Dong ◽  
...  
Keyword(s):  
Residual Stress ◽  
Formation Mechanism ◽  
Welded Joints ◽  
High Strength Steel ◽  
Hydrogen Pressure ◽  
High Strength ◽  
Welding Residual Stress ◽  
Cracking Behavior ◽  
Hydrogen Damage ◽  
Delayed Cracking

Based on the estimation of the critical hydrogen pressure and concentrations required for hydrogen-induced delayed cracking in high-strength steel, the conclusion that welded joints are hydrogen pressure microcracks body can be drawn under certain conditions. Through the analysis of the relationship between the microstructure evolution of welded joints, diffusion enrichment of hydrogen and cracking behavior, the formation mechanism of hydrogen-induced delayed cracking in weld center of high-strength steel joints is analyzed and the mechanism that stress induced the residual diffusion hydrogen gathered to promote the hydrogen pressure microcracks propagation is proposed. The research shows that the initation and propogation of hydrogen-induced delayed cracking in weld center can be divided into two stages, i.e. irreversible hydrogen damage stage and reversible hydrogen damage stage. In irreversible stage hydrogen pressure is the main causes of the initation of microcracks, while in reversible stage welding residual stress and residual diffusible hydrogen are necessary conditions for microcracks growth. The microcracks growth can be controlled by regulating welding residual stress.

Predicting Welding Residual Stress Distributions in P92 Steel Joints Considering the Influence of Solid-State Phase Transformation

2016 ◽  
Author(s):  
Dean Deng ◽  
Hidekazu Murakawa
Keyword(s):  
Residual Stress ◽  
Phase Transformation ◽  
Solid State ◽  
Computational Approach ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Stress Distributions ◽  
P92 Steel ◽  
Solid State Phase Transformation ◽  
Steel Joints

In this study, an advanced computational approach based on SYSWELD software was developed to simulate welding residual stress distributions in P92 steel joints with the consideration of solid-state phase transformation. Using the developed numerical method, we calculated the welding residual stress distribution in a single-pass weld joint, and clarified the influences of volume change, variation of yield strength and phase transformation induced plasticity on the formation of residual stress. Meanwhile, experiment was carried out to measure the welding residual stress distributions in the single-pass joint. The effectiveness of the developed computational approach was verified by the experimental results. In addition, the features of welding residual stress distribution in multi-pass P92 steel joint were discussed based on the results obtained by numerical simulation, and some new viewpoints on welding residual stress in multi-pass P92 steel joints were obtained.

Dynamic Response Analysis of Butt Joint of HTS-A Steel Considering Welding Residual Stresses

2013 ◽  
Vol 423-426 ◽  
pp. 944-950
Author(s):  
Wei Shen ◽  
Ren Jun Yan ◽  
Lin Xu ◽  
Kai Qin ◽  
Xin Yu Zhang ◽  
...  
Keyword(s):  
Residual Stress ◽  
Dynamic Response ◽  
Hot Spot ◽  
Time History ◽  
High Strength ◽  
Simulation Method ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Response Analysis ◽  
Hull Structure

This paper uses both numerical simulation method and experimental research method to study on welding residual stress of high-strength steel of the cone-cylinder hull. Welding is often accompanied by a larger welding residual stress, which directly affects the safety and service life of the hull structure. In order to obtain the distribution of the welding residual stress, the welding procedure was developed by its parameter language by using FE analysis software in this paper. Then the welding residual stress of hot spot region was measured through X-ray nondestructive testing method, and compared it with simulation results. Finally, considering the residual stress as the initial stress, this paper analyzed dynamic response process of the welding structure under combined actions of the welding residual stress and multiaxial loads, which could more accurately determine the stress of welding structure and the location of fatigue risk point. According to the amplitude of damage parameters and strain time-history curve, we can estimate the fatigue life of structure by selecting the corresponding damage models.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Sign in / Sign up

Export Citation Format

Share Document