Forming of aluminum foam sandwich panels: Numerical simulations and experimental tests

2006 ◽  
Vol 177 (1-3) ◽  
pp. 364-367 ◽  
Author(s):  
D. Contorno ◽  
L. Filice ◽  
L. Fratini ◽  
F. Micari
Keyword(s):  
Numerical Simulations ◽  
Aluminum Foam ◽  
Sandwich Panels ◽  
Experimental Tests

Impact and close-in blast response of auxetic honeycomb-cored sandwich panels: Experimental tests and numerical simulations

2017 ◽  
Vol 180 ◽  
pp. 161-178 ◽  
Author(s):  
Chang Qi ◽  
Alex Remennikov ◽  
Lian-Zheng Pei ◽  
Shu Yang ◽  
Zhi-Hang Yu ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Sandwich Panels ◽  
Experimental Tests ◽  
Blast Response

scholarly journals AC Current Ripple in Three-Phase Four-Leg PWM Converters with Neutral Line Inductor

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1430
Author(s):  
Aleksandr Viatkin ◽  
Riccardo Mandrioli ◽  
Manel Hammami ◽  
Mattia Ricco ◽  
Gabriele Grandi
Keyword(s):  
Numerical Simulations ◽  
Pulse Width Modulation ◽  
Neutral Line ◽  
Experimental Tests ◽  
Performance Comparison ◽  
Design Parameters ◽  
Switching Frequency ◽  
Three Phase ◽  
Ac Current ◽  
Current Ripple

This paper presents a comprehensive study of peak-to-peak and root-mean-square (RMS) values of AC current ripples with balanced and unbalanced fundamental currents in a generic case of three-phase four-leg converters with uncoupled AC interface inductors present in all three phases and in neutral. The AC current ripple characteristics were determined for both phase and neutral currents, considering the sinusoidal pulse-width modulation (SPWM) method. The derived expressions are simple, effective, and ready for accurate AC current ripple calculations in three- or four-leg converters. This is particularly handy in the converter design process, since there is no need for heavy numerical simulations to determine an optimal set of design parameters, such as switching frequency and line inductances, based on the grid code or load restrictions in terms of AC current ripple. Particular attention has been paid to the performance comparison between the conventional three-phase three-leg converter and its four-leg counterpart, with distinct line inductance values in the neutral wire. In addition to that, a design example was performed to demonstrate the power of the derived equations. Numerical simulations and extensive experimental tests were thoroughly verified the analytical developments.

Heat Transfer Increase by Flow Structures Modifications

2005 ◽  
Author(s):  
Charles-Andre´ Lemarie´ ◽  
Nachida Bourabaa ◽  
Franc¸ois Monnoyer ◽  
Tewfik Benazzouz
Keyword(s):  
Heat Transfer ◽  
Simple Model ◽  
Kinetic Energy ◽  
Numerical Simulations ◽  
Experimental Tests ◽  
Flow Structures ◽  
Driven Cavity ◽  
Simple Geometry ◽  
Through Flow ◽  
Do So

This paper makes use of a new methodology for heat transfer increase through flow structures modifications. Intended to help railway designers in handling cooling issues, it is applied to improve the roof-mounted equipment design of a modern railway coach, namely the CORADIA TER 2N NG produced by the ALSTOM Transport company. The brake resistor, a key equipment in charge of dissipating the train kinetic energy as heat into the surrounding air during braking phases, has been particularly considered. To do so, a simple model including a heated obstacle inside a three-sided lead-driven cavity is used, and simple geometry variations are suggested. Their impact on heat transfer is then estimated through numerical simulations while experimental tests validate the results obtained.

scholarly journals Flexural behavior of sandwich panels with cellular wood, plywood stiffener/foam and thermoplastic composite core

2017 ◽  
Vol 21 (2) ◽  
pp. 784-805 ◽  
Author(s):  
Edgars Labans ◽  
Kaspars Kalnins ◽  
Chiara Bisagni
Keyword(s):  
Mechanical Performance ◽  
Sandwich Panels ◽  
Experimental Tests ◽  
Design Tool ◽  
Thermoplastic Composite ◽  
Flexural Behavior ◽  
Four Point Bending ◽  
Reliable Design ◽  
Sufficient Strength ◽  
Core Part

A series of experimental tests have been carried out on three types of novel sandwich panels mainly designed for application in lightweight mobile housing. Two types of the panels are manufactured entirely from wood-based materials while the third one presents a combination of plywood for surfaces and corrugated thermoplastic composite as a core part. All sandwich panels are designed to allow rapid one-shot manufacturing. Mechanical performance has been evaluated in four-point bending comparing the data to the reference plywood board. Additionally, finite element simulations were performed to evaluate global behavior, stress distribution and provide the basis for a reliable design tool. Obtained results show sufficient mechanical characteristics suitable for floor and wall units. Compared to a solid plywood board, sandwich alternative can reach up to 42% higher specific stiffness, at the same time maintaining sufficient strength characteristics.

Rounded Fin Edge and Step Position Effects on Discharge Coefficient in Rotating Labyrinth Seals

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Andrea Rapisarda ◽  
Alessio Desando ◽  
Elena Campagnoli ◽  
Roberto Taurino
Keyword(s):  
Experimental Data ◽  
Numerical Simulations ◽  
Leading Edge ◽  
Experimental Tests ◽  
Velocity Profiles ◽  
Pollutant Emission ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Position Effects ◽  
Impact Reduction

The design of modern aircrafts propulsion systems is strongly influenced by the important objective of environmental impact reduction. Through a great number of researches carried out in the last decades, significant improvements have been obtained in terms of lower fuel consumption and pollutant emission. Experimental tests are a necessary step to achieve new solutions that are more efficient than the current designs, even if during the preliminary design phase, a valid alternative to expensive experimental tests is the implementation of numerical models. The processing power of modern computers allows indeed the simulation of more complex and detailed phenomena than the past years. The present work focuses on the implementation of a numerical model for rotating stepped labyrinth seals installed in low-pressure turbines. These components are widely employed in sealing turbomachinery to reduce the leakage flow between rotating components. The numerical simulations were performed by using computational fluid dynamics (CFD) methodology, focusing on the leakage performances at different rotating speeds and inlet preswirl ratios. Investigations on velocity profiles into seal cavities were also carried out. To begin with, a smooth labyrinth seal model was validated by using the experimental data found in the literature. The numerical simulations were extended to the honeycomb labyrinth seals, with the validation performed on the velocity profiles. Then, the effects of two geometrical parameters, the rounded fin tip leading edge, and the step position were numerically investigated for both smooth and honeycomb labyrinth seals. The obtained results are generally in good agreement with the experimental data. The main effect found when the fin tip leading edge was rounded was a large increase in leakage flow, while the step position contribution to the flow path behavior is nonmonotone.

Sign in / Sign up

Export Citation Format

Share Document