Application of pre-deformation rolling in the welding heat-affected zone of tailor-welded blanks formed by deep-drawing process

2020 ◽  
Vol 51 ◽  
pp. 151-160
Author(s):  
Zengliang Hao ◽  
Junting Luo ◽  
Yongbo Jin ◽  
Dawei Meng ◽  
Chunxiang Zhang
Keyword(s):  
Heat Affected Zone ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Tailor Welded Blanks

The Influence of the Blank Holder Force on Material Thinning during Forming of a Rectangular Part Made from Tailor Welded Blanks

2014 ◽  
Vol 1036 ◽  
pp. 344-348
Author(s):  
Aurelian Albut ◽  
Vlad Andrei Ciubotariu
Keyword(s):  
Deep Drawing ◽  
Drawing Process ◽  
Blank Holder Force ◽  
Forming Process ◽  
Blank Holder ◽  
Deep Drawing Process ◽  
Tailor Welded Blanks ◽  
Tailored Blanks ◽  
Welded Structure ◽  
Welding Line

The current work deals with numerical simulation connected to forming of a rectangular shaped part made from tailored blanks, having the welding line positioned symmetrical with respect to the part geometry. The objective was to study the relation between the blank holder force applied during forming and the thinning of the parents materials. All the parameters are fixed except the blank holder force, its variation will cause variation of the material thinning. The presented work is trying to demonstrate the important role of the blank holder force on the material thinning during the deep drawing process. It must be mentioned that both materials from the welded structure are having the same thickness (1mm). The Dynaform 5.8.1 software is used to simulate the forming process. The part obtained after each simulation is analyzed and measured to quantify the on the material thinning. All the parameters are maintained fixed except the blank holder force. The obtained results for five different binder forces (5, 10, 30, 50, 70 kN) were compared to realise the behaviour of the tailor welded blanks during deep drawing process. In the final part of this paper conclusions regarding the influence of the blank holder force on the material thinning are presented.

Deep-Drawing Process Simulation for Tailor-Welded Blanks with an Elastic Blankholder

2017 ◽  
Vol 49 (4) ◽  
pp. 586-593
Author(s):  
A. Brusilová ◽  
A. Schrek ◽  
P. Švec ◽  
Z. Gábrišová
Keyword(s):  
Process Simulation ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Tailor Welded Blanks

scholarly journals Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3993
Author(s):  
Thanh Trung Do ◽  
Pham Son Minh ◽  
Nhan Le
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Side Wall ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

Blank shape optimization in the deep drawing process by sun method

2021 ◽  
Author(s):  
Hamidreza Gharehchahi ◽  
Mohammad Javad Kazemzadeh-Parsi ◽  
Ahmad Afsari ◽  
Mehrdad Mohammadi
Keyword(s):  
Shape Optimization ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Blank Shape Optimization ◽  
Blank Shape

Production of Tapered Cups by Sequential Deep Drawing of Sheet Metals Using Drawn Cups as a Part of Punch

1993 ◽  
Vol 115 (2) ◽  
pp. 224-229 ◽  
Author(s):  
K. Yamaguchi ◽  
K. Kanayama ◽  
M. H. Parsa ◽  
N. Takakura
Keyword(s):  
Deep Drawing ◽  
Drawing Ratio ◽  
Drawing Process ◽  
Sheet Metals ◽  
Deep Drawing Process ◽  
Drawing Method

A new deep drawing process of sheet metals is developed to facilitate small-lot production of deep cups with large drawing ratio. In this process, unlike the conventional deep drawing method, a few drawn cups are always stacked on the punch and used as a part of punch for the subsequent deep drawing of a given blank. Before drawing a new blank, a drawn cup which is in contact with the punch is stripped off. The repetition of such stripping and drawing operations makes it possible to carry out both the first-stage drawing and the subsequent slight redrawings in one drawing operation using only one pair of punch and die. In this paper, this new deep drawing process is applied to the production of tapered cups and the main feature of the process is shown.

Sign in / Sign up

Export Citation Format

Share Document